Nicai Systems Nibo2 Manual de Usario

Lee a continuación 📖 el manual en español para Nicai Systems Nibo2 (44 páginas) en la categoría No categorizado. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/44
Robot kit Nibo2
Construction manual
Construction manual for robot kit Nibo2 22.11.2011
Safety instructions
For construction and operation of the robot please consider the
following safety instructions:
The robot kit Nibo2 is designed for learning, teaching and experimental
purposes only. The company does not accept any liability for other
uses of the programming adapter. Any other use is at the users own
risk.
No machines must be attached to the robot. In particular the operation
with devices on mains voltage is forbidden.
The robot must not be operated without supervision. When not in use
the robot is to be separated from the power supply.
The robot must be operated with stabilized DC voltage by 9.6 V. In
particular the robot must be operated with rechargeable batteries
(1,2V) only and never with normal batteries (1,5V).
We take no responsibility for data loss of an attached computer.
The robot must be used indoors only. In particular the usage of the
robot is expressly forbidden on public roadways!
For a usage deviating from these guidelines no warranty and no
accountability are assumed, the operation is at your own risk!
For soldering please consider following points:
Always work with extreme caution with the soldering iron!
Inappropriate operation can lead to severe burns or cause fires.
Never place the hot soldering iron on the table or on other surfaces.
Never leave the soldering iron switched on unsupervised.
Please consider the possible emission of poisonous fumes when
soldering. Ensure there is sufficient ventilation and wash your hands
thoroughly after work.
Keep the soldering iron away from children!
Please consider the safety instructions of the soldering iron
manufacturer!
Pay attention to a correct soldering tip temperature: High temperatures
(400°C) may damage the tip, but also allow a short soldering time. Low
temperatures (320°C) will increase the soldering time. This may
damage the electronic components.
http://nibo.nicai-systems.com 2
Construction manual for robot kit Nibo2 22.11.2011
Table of contents
1 Introduction and overview.............................................................................5
1.1 Features.................................................................................................6
1.2 Motors....................................................................................................7
1.2.1 Odometry........................................................................................7
1.2.2 Motor bridge....................................................................................8
1.2.3 Motor controller...............................................................................8
1.3 Sensors..................................................................................................8
1.3.1 Distance measuring........................................................................8
1.3.2 Floor- and line-following sensors....................................................9
1.4 Communication......................................................................................9
1.4.1 IR-receiver......................................................................................9
1.4.2 IR-transmitter..................................................................................9
1.4.3 ISP interface...................................................................................9
1.4.4 Extension port...............................................................................10
1.5 Other hardware components...............................................................10
1.5.1 Status LEDs..................................................................................10
1.5.2 Lighting.........................................................................................10
1.5.3 Configuration jumper and function button....................................10
1.5.4 Reset button and voltage switch...................................................10
1.5.5 Display..........................................................................................10
2 Assembling of the robot...............................................................................11
2.1 Necessary tools....................................................................................11
2.2 Soldering..............................................................................................11
2.3 Odometry sensor boards.....................................................................12
2.3.1 10-way headers............................................................................13
2.3.2 Multi colour LEDs..........................................................................14
2.3.3 IR-LEDs........................................................................................14
2.3.4 Miniature speaker.........................................................................14
2.3.5 Resistors ......................................................................................15
2.4 Assembling of the engine section........................................................16
2.5 Placing components onto the main board...........................................20
2.5.1 Resistor.........................................................................................22
2.5.2 Diodes...........................................................................................22
2.5.3 Photoelectric reflex-sensors.........................................................23
2.5.4 IR-photo-transistors......................................................................23
2.5.5 IR-LEDs........................................................................................24
2.5.6 White LEDs...................................................................................24
2.5.7 Multi colour LEDs..........................................................................24
2.5.8 Button............................................................................................24
2.5.9 Jumper..........................................................................................25
2.5.10 10-way sockets...........................................................................25
2.5.11 Connectors..................................................................................25
http://nibo.nicai-systems.com 3

Especificaciones del producto

Marca: Nicai Systems
Categoría: No categorizado
Modelo: Nibo2
Colocación del dispositivo: Ingebouwd
Tipo de operación: Draaiknop
Color del producto: Black, Stainless steel
Bisagras de puerta: Neer
Pantalla incorporada: Nee
Ancho: 594 mm
Profundidad: 535 mm
Altura: 594 mm
Parrilla: Ja
control wifi: Nee
Clase-de-eficiencia-energética: A
cocinar al vapor: Nee
Capacidad interior total (hornos): 65 l
Número de hornos: 1
Fácil de limpiar: Ja
Posición de control: Voorkant
Ancho del compartimento de instalación: 560 mm
Profundidad del compartimento de instalación: 510 mm
Altura del compartimento de instalación: 595 mm
Material a través: Glas
Consumo de energía (convencional): 1.7 kWu
Consumo de energía (convección forzada): 1.89 kWu
Tamaño del horno: Middelmaat
tipo de horno: Aardgas
Potencia total del horno: - W
Horno de capacidad neta: 65 l
magnetrón: Nee
Rango de termostato del horno: 0 - 250 °C
Tipo temporizador: Mechanisch
Número de programas de cocina: 6
Escala de eficiencia energética: A+++ tot D

¿Necesitas ayuda?

Si necesitas ayuda con Nicai Systems Nibo2 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Nicai Systems Manuales

No categorizado Manuales

Últimos No categorizado Manuales