Oliveri FS7025 Manual de Usario

Oliveri filtro de agua FS7025

Lee a continuación 📖 el manual en español para Oliveri FS7025 (3 páginas) en la categoría filtro de agua. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

SATELLITE WATER FILTRATION SYSTEM

FS7025 FS7075 FS7005

WAT E R DR I N K I N G S Y ST E M S

OWNER’S MANUAL

HEALTH CLAIM PERFORMANCE CLASSIFIED BY NSF.

This system has been tested according to NSF/ANSI 42 and 53 for the reduction of the

substances listed below.

The concentration of the indicated substances in water entering the system was reduced

to a concentration less than or equal to the permissable limit for water leaving the system,

as speciﬁed in NSF/ANSI 42 and 53.

OPERATING SPECIFICATIONS:

• Capacity: 9,450 litres

• Pressure Requirement: 10-125 psi (0.7 - 8.6 bar), non-shock.

• Temperature: 2-38O C

• Flow Rate: 0 - 1.9 litres per minute.

GENERAL INSTALLATION / OPERATION/MAINTENANCE

REQUIREMENTS:

• Space required: 460mm x 225mm (allows space for cartridge replacement)

• Install cartridge vertically or horizontally with stabilizing support bracket.

• Flush new cartridge at full ﬂow for 2–3 minutes until air is purged.

• Replace cartridges when capacity is reached, or when ﬂow becomes too slow, but at least annually.

SPECIAL NOTICES:

• Installation instructions, parts and service availability, and standard warranty are included with

the product when shipped.

• This drinking water system must be maintained according to manufacturer’s

instructions, including replacement of ﬁlter cartridges.

• Do not use with water that is microbiologically unsafe, or of unknown quality without adequate

disinfection before or after the system.

• The contaminants or other substances removed or reduced by the water

treatment system are not necessarily in your water.

• Check for compliance with state and local laws and regulations.

FS7025, FS7075, FS7005

Performance Data

Important Notice:

Read this performance data sheet and compare the capabilities of this

unit with your actual water treatment needs.

FEATURES:

Filters water through designer ﬁlter tap

Provides quality ﬁltered water without compromising on ﬂow rate

Easy installation and space saving design

Compatible with any bench top including solid surface

Suitable for vertical or horizontal installation to maximise cupboard space

Finely ﬁlters to 1 micron and polishes mains water to a premium quality for:

• Drinking

• Cooking

The latest carbon block ﬁltration technology absorbs:

• Chlorine

• Bad tastes

• Odours

Maintains healthy minerals and salts as well as ﬂuoride

Helps to prevent the build up of limescale

Simple, easy to change cartridge replacements

• Dirt

• Rust

• Cysts (e.g. giardia & cryptosporidium)

• Tea & coffee

• Washing fruits & vegetables

*Tested using ﬂow rate=0.5gpm; pressure=60psig; pH=7.5 ± 0.5; temp=20oC ± 2.5oC †NTU=Nephelometric Turbidity Units

Max. Permissible

Subtance Inﬂuent Challenge Product Water Reduction Minimum Average

Requirements Concentration Concentration Requirements Reduction

Standard 42 Aesthetic Effects

Chlorine 2.0mg/L±10% 5ppm ≥50% - 98%

Particulate at least 10,000 - ≥85% - 99.8%

Class 1 particles particles/mL

<1um

Standard 53 Health Effects

Cyst Minimum 50,000/L - 99.95% 99.99% 99.99%

Turbidity 11±1 NTU

† 0.5 NTU1 - 98% 99%

Check for compliance with state and local laws and regulations. Product performance is

dependant upon incoming water conditions. This drinking water system must be maintained

according to the manufacturer’s instructions, including replacement of cartridge.

AS3497

Lic.WMKA22045

IAPMO R&T OCEANA

This appliance meets the domestic water treatment

appliance Standards AS/NZS3497 for the following

water treatment processes:

WARNING: FOR CORRECT OPERATION

OF THIS APPLIANCE IT IS ESSENTIAL

TO OBSERVE THE MANUFACTURER’S

INSTRUCTIONS.

CLASS TREATMENT TYPE FUNCTION PASS

II. II (a)

II (b)

III (c)

III.

IV.

Microbiological Status

Bacteriostatic

Microbiological Treatment

Bacteria Removal

Virus Removal

Protozoa Removal

Turbidity and Particulate

Reduction

Taste and Odour Reduction

Will stop bacteria increasing but will

not stop them unless IIa is passed.

Will remove or inactivate bacteria.

Will remove or inactivate virus.

Will remove or inactivate

Cryptosporidium and Giardia.Will

not remove or inactivate bacteria and

virus unless II(a) and II(b) is passed.

Reduces Cloudiness

Reduces Tastes and Odours

N/A

System tested and Classiﬁed by

Underwriters Laboratories Inc

against NSF/ANSI Standards

42 and 53 for the reduction of:

Std. No 42 -

Aesthic Effects

Chemical Reduction

Chlorine

Taste & Odour

Mechanical Filtration

Nominal Particulate Class 1

Std. No 53 -

Health Effects

Mechanical Filtration

Cyst

Turbidity

WATER QUALITY

WATER FILTER

ANSI/NSF

STANDARDS

42 AND 53

3LSD

Distributed by:

Tasman Sinkware Pty Ltd.

51 Naweena Rd, Regency Park, SA, 5010

1300 137 465

sinkware@oliverisinks.com.au

oliveri.com.au

INSTALLATION INSTRUCTIONS

1. Open Carton and Inspect Parts. Installation

Parts included – refer installation diagram

Item No.

Cistern Tap 1

/2” fbsp x 1

/2” mbsp (1)

Dual Check Valve 1

/ ”2 fbsp x 1

/ ”2 mbsp (2)

Pex Hose 750mm (3)

Head Assembly (4)

Filter Cartridge (5)

Pex Hose 550mm (6)

Filter Tap (7)

Filter Monitor Alarm (8)

Mounting Screws (9)

IMPORTANT NOTES

• When installing this ﬁlter system in a new home or

kitchen please ensure that the cold water lines under

the sink are ﬂushed to remove all debris within the

pipes, before installation of the water ﬁlter system.

• This Water Filtration System should be installed in

accordance with any local Water Authority by-laws.

Australian Standard AS3500

• Where water pressure exceeds 860 kPa a suitable

pressure limiting valve should be installed prior to

connection to the ﬁlter system.

2. Connect to Water Supply

It is advisable to turn off the water supply at the

mains before commencing installation.

Check to see if separate water connection is provided.

IF A SEPARATE WATER CONNECTION IS NOT

PROVIDED

• Locate the cistern tap mounted on the wall

underneath the sink for the existing cold water

line.

• Turn off isolation cistern tap and disconnect

attached ﬁttings.

Attach the following parts to the existing cistern tap

according to the Connection Diagram below

Using plumbing tape:

• Attach the following parts to the cistern tap

according to the Connection Diagram below.

Brass Female Tee 1

/ 2” BSP*

Brass Nipple 1

/2” BSP – 1

/ 2” BSP (x2)*

Cistern Tap supplied

• Reconnect the cold water line to the available

/2” connection. Firmly tighten all connections

* Parts not included with system.

3. Undersink Mounting Position

This Water Filter System can be installed in either

the horizontal or vertical position.

a) Vertical Installation

Measure 460m from the base of the cabinet (or

shelf), and mark the mounting location for the

top of the ﬁlter head. Make sure that there is

adequate space to avoid crimping the water line

ﬂex hoses. Also make sure your chosen location

offers easy access for future cartridge changes.

b) Horizontal Position Measure 460mm

horizontally, and mark the mounting location

for the side of the ﬁlter head and end of the

ﬁlter cartridge. Make sure that there is adequate

space to avoid crimping the water line ﬂex

hoses. Also make sure your chosen location

offers easy access for future cartridge changes.

4. Important - If necessary you can easily change

the direction of the ﬂow of water through

the inlet and outlet of the ﬁlter system. You

will notice on the head assembly that the inlet

is shown by the word “IN” and the outlet is

shown by the word “OUT”. To change direction,

simply remove the four (4) screws that hold

the mounting bracket to the head assembly

and replace/reﬁt the mounting bracket in the

opposite direction. This allows ﬂexibility when

choosing the desired location for your ﬁlter

system.

a) Apply plumbing tape to the Pex Hose 3/8” male

connection (item 3). Wrap tape in direction of the

thread to ensure a tight ﬁt and avoid leaks. Screw

this connection to the inlet side of the ﬁlter head

assembly (item 4). Repeat same for the Pex Hose

(Item 6) on the outlet side of the Head Assembly

(Item 4)

b) Securely mount the Filter Head Assembly

(item 4) on the cabinet wall using two of the

mounting screws (item 9) provided.

5. Connect Dual Check Valve – (item 2)

IMPORTANT – It is a legal requirement under

Australian Plumbing Standards that the Dual

Check Valve be installed. If this part is not

installed all warranties are null and void.

a) Apply plumbing tape to the 1/2” male

connection on the outlet of the existing cistern

tap. Wrap tape in direction of the threads to

ensure a tight ﬁt and avoid leaks. Screw on the

Dual Check Valve (item 2) and secure.

6. Attach Pex Hose (item 3)

Connect the 1

/2” female end of the Pex Hose (item

3) to the 1

/2” male end of Dual Check Valve.

7. Install the Filter Tap (refer diagram)

Assemble and mount the tap. Tighten locking

nut beneath the sink to secure the tap ﬁrmly in

position. If a hole for the ﬁlter tap is not provided,

then use a drill or hole cutter to cut a 12.7mm (1

/2”)

hole in the sink or counter top where the tap is to

be located.

Please ensure that you use plumbing tape when

connecting the chrome brass adaptor to the

bottom of the ﬁlter tap.

8. Attach Filtered Water to Cold Water Line of

Filter Tap

Take the braided pex hose from the outlet of the

head assembly and connect to the chrome brass

adaptor at the bottom of the ﬁlter tap.

9. Flush the Filter Cartridge

a) Turn water supply back on at either the mains

or at the cold water mini cistern tap.

b) At this stage check for leaks and ﬁx if necessary

c) Turn kitchen tap on and ﬂush the ﬁlter

cartridge for at least 2–3 minutes. Collect

water in container and use for garden etc.

NOTE – Flushing the ﬁlter cartridge is important to

remove air from the system and any loose carbon

powder. At ﬁrst the water may appear cloudy due

to compressed trapped air in the ﬁlter and hoses.

However the cloudiness will disappear over time

and with use.

10. Installing the Filter Monitor Alarm (item 8)

The ﬁlter monitor alarm (item 8) is supplied to

assist you with knowing when it is time to replace

your ﬁlter cartridge. Regular annual cartridge

replacement ensures that your ﬁlter system is

maintained in accordance with the manufacturers

recommendations.

a) Remove plastic wrapper from monitor and

remove installation instructions.

b) On the back of the monitor - pull the tab back.

c) The LED and buzzer will cycle 3 times to

conﬁrm the start.

d) It is programmed to ﬂash and sound again in

11 months.

e) Remove the two adhesive tapes from the

back of the monitor and locate/mount in a

convenient location under your kitchen sink.

NOTES

1) This installation must comply with all

applicable state and local regulations.

2) Do not use with water that is

microbiologically unsafe or of an unknown

quality without disinfection before or after

the system.

3) When storing ﬁltered water in a refrigerator

please ensure the container has an air tight

seal / lid.

Tasman Sinkware warrants to you, the ﬁrst person

who has purchased and used the unit (“you”) that

this unit is free from defects due to faulty material and

workmanship in accordance with the conditions set out

in this document. This warranty is provided to you in

addition to your rights at law, including but not limited

to your rights under the Trade Practices Act 1074 (Cth)

and applicable legislation in your Australian State or

Territory.

What this warranty covers:

This warranty covers defects due to faulty material and

workmanship of the unit supplied to you:

• For a period of 6 years from the date of purchase in

respect of the entire unit, excluding the Replaceable

Elements. The Replaceable Elements are consumable

components and all parts of the unit which can be

replaced including but not limited to the ﬁlter or water

treatment cartridge if there is a defect in the ﬁlter or

cartridge. This does not include the replacement of

the ﬁlter or cartridge to extend the life of the ﬁlter or

cartridge. The life of the ﬁlter cartridge is affected by

water quality, usage and water pressure. The warranty

only extends to the original purchaser of the unit.

What this warranty does not cover:

This warranty does not cover the unit or a Replaceable

Element of the unit where:

• The defect, fault or failure is attributable, or

substantially attributable to misuse, abuse, accident,

misapplication, neglect, freezing, oxidizing agents

(including but not limited to chlorine, ozone,

chloramines and other related components) or act of

God;

• The unit has been in conditions which do not conform

to the recommended design guidelines or has been

operated in a manner which is contrary to Tasman

Sinkware’s printed instructions;

PRODUCT

SPECIFICATION

• Usage: For mains cold

water only.

• Temperature Range: 2-38oC

• Min.-Max. Working

Pressure:10-125 psi

(0.7-8.6 bar)

• Service Flow Rate:

0–3 Litres per minute*

• Capacity: 9,450 litres*

• Rating: 1 micron

• Removes/Reduces:

Chlorine, cysts, giardia,

cryptosporidium, bad taste

and odours, and all particles

down to 1 micron in size

• This ﬁlter does not remove

ﬂuoride

• Filter Change: Annually or

sooner if ﬂow rate becomes

inconveniently slow.

• The unit has not been installed in accordance with

Tasman Sinkware’s printed instructions and has not

been installed in compliance with all applicable laws,

regulations and industry standards;

• The unit has not been used in accordance with the

manufacturer’s instructions;

• The unit does not meet the conditions for use

described in the owner’s manual or performance data

sheet for this unit

• You use accessories or components which do not

meet Tasman Sinkware’s speciﬁcations as set out in the

Owners Manual;

• The defect, fault or failure is due to normal wear and

tear;

• The defect, fault or failure has occurred where the unit

has been used reasonably or has reached its serviceable

life;

• The serial or model number label of the unit is

removed or defaced;

• The unit is serviced, modiﬁed, altered or repaired

by an unauthorized or unqualiﬁed person;

How to make a claim under this warranty:

To make a claim under this warranty you must contact

Tasman Sinkware within 21 days of the defect, fault or

failure occurring. Tasman Sinkware’s Warranty Contact

number is 1300 13 7465. At the time of repair or

replacement under your warranty claim you must provide

to Tasman Sinkware:

• Proof that you purchased the unit from an authorized

retailer or dealer within the warranty time; and

• A copy of a certiﬁcate which certiﬁes that the unit was

installed in compliance with our printed installation

instructions and all applicable laws, regulations and

industry standards. Tasman Sinkware will only pay for

repair or replacement upon receipt of proof of your

purchase showing the date of purchase.

Limitation of Liability of Tasman Sinkware under

this warranty: Where a warranty exists or is implied by

law, Tasman Sinkware liability is limited (to the extent

that it can be limited) to repair or replacement of the

faulty Replaceable Element or the unit or an equivalent

unit. Tasman Sinkware may, in its discretion, choose

whether it shall repair or replace any unit or Replaceable

Element or Tasman Sinkware may choose to pay to you

the cost of replacing the Replaceable Element or the unit

or the cost of having the unit repaired. To the extent

permitted by law, Tasman Sinkware assumes no liability

whatsoever and disclaims all liability for direct, indirect or

consequential loss, or special, general or other damage

or expense caused by or arising out of:

• Any failure to install or use the unit in accordance

with the Manufacturer’s Instructions, the Installation

and Operating manual or Tasman Sinkware’s printed

instructions; or

• The purpose for which you are purchasing the unit.

You acknowledge that the quality of water supplied and

your water usage rate and inﬂuent water pressure may

vary seasonally or over a period of time.

In addition to this water characteristics can differ if the

unit is relocated or the environment changes.

You acknowledge that Tasman Sinkware does not know

your requirements and cannot and does not warrant that

the unit is ﬁt for the purpose for which you intend to

use the unit or is appropriate for the purpose for which

you intend to use the unit. Tasman Sinkware does not

authorize others to assume any obligation on its behalf

even if you inform them of the purpose for which you

intend to use this unit.

WARNING Tasman Sinkware does not recommend

making alterations to your existing plumbing to

accommodate this ﬁlter system. If you wish to modify

existing plumbing you must comply with AS 3500 and

use a licensed plumber. Where internal water pressure

exceeds 860 kPa a Watermark approved Pressure

Limiting Valve must be installed prior to the ﬁlter system.

WARNING The contaminants or other substances

removed or reduced by this water treatment system are

not necessarily in your water supply. Do not use with

water that is microbiologically unsafe or of an unknown

quality without disinfection before or after the system.

IMPORTANT This ﬁlter is designed to be used with

mains/city water supplies.

CAUTION Safely isolate the water supply prior to

installing the ﬁlter system to avoid injury and

property damage.

Our goods come with guarentees that cannot be

excluded under the Australian Consumer Law. You

are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have

all the goods repaired or replaced if the good fails to be

of acceptable quality and the failure does not amount to

a major failure.

Refer to oliveri.com.au for warranty details.

Product Speciﬁcations: The unit must only be used for a portable

water source and with cold water (with a temperature range

between 2 and 38° C).

FS7025, FS7075, FS7005

WARRANTY

(1) Cistern Tap 1

/2” fbsp x 1

/2” mbsp

(2) Dual Check Valve 1

/ ”2 fbsp x 1

/ ”2 mbsp

(3) Pex Hose 750mm

(4) Head Assembly

(5) Filter Cartridge

(6) Pex Hose 550mm

(7) Filter tap

(8) Filter Monitor Alarm

(9) Mounting Screws

Hot Water Line

Filtered

cold

water

Cold

Water

Line

FILTER ALARM

* Subject to water quality and usage

TO FILTER

TO MIXER

EXISTING COLD

WATER CISTERN TAP

CONNECTION DIAGRAM

TAP INSTALL DIAGRAM

RUBBER WASHER

PLASTIC WASHER

LOCKING WASHER

NUT

CHROME BRASS ADAPTOR

Owners Manual

Especificaciones del producto

Marca:	Oliveri
Categoría:	filtro de agua
Modelo:	FS7025

¿Necesitas ayuda?

Si necesitas ayuda con Oliveri FS7025 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

filtro de agua Oliveri Manuales

Oliveri FS7025 Manual de Usario

12 Septiembre 2024

Oliveri FS7075 Manual de Usario

12 Septiembre 2024

filtro de agua Manuales

Últimos filtro de agua Manuales

Astralpool Oslo Manual de Usario

27 Octubre 2024

Laica J35-AD Manual de Usario

15 Octubre 2024

Laica J35-EB Manual de Usario

15 Octubre 2024

Laica J11-AB Manual de Usario

15 Octubre 2024

Laica J51-BC Manual de Usario

15 Octubre 2024

GE GX1S15C Manual de Usario

13 Octubre 2024

Grohe Red Manual de Usario

11 Octubre 2024

Grohe 31381DC1 Manual de Usario

4 Octubre 2024

Fluval AquaClear AC30 Manual de Usario

24 Septiembre 2024

Fluval AquaClear AC50 Manual de Usario

24 Septiembre 2024