Oliveri VE570FBN Manual de Usario
Lee a continuación 📖 el manual en español para Oliveri VE570FBN (2 páginas) en la categoría Grúa. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Venice
T S MIXER TAP MUST BE INSTA ED BY A LICEN D PLUMBER IN HI LL SE
ACCORD CE WITH LO L EGULATIONS. AN CA R
This Oliveri tap is manufactured to standard AS/N 3 . ZS 718
MAX OPERATING PRE URE: .. . . . . . ... . . . . .. 5 bar ( 0kPa) SS .... ... ... .... .... ... .... .. .... .. .. .... .. .. .. .. .. .... .. .. .. .. .. .... 50
RECOMMENDED OPERATION PRESSURE: .. .. .... .... .... .. .. .. .. .. ... . . . . ... . .. .. . . . ..... .. ... .. ... .. ... . 1.5-5 bar (150- 0kPa) 50
MAX HOT WATER TEMPERAT E: UR .. .. .... .... .... .. .. .. .. .. .. .. .. .. .. ... . . . . ... . .. . .. .. ... .. .... . . .. .. .. .. .. 65°C
RECOMMENDED HOT WATER TEM RATURE: PE .. .. .... .... .... .. ... . . . . ... .. .. ... .. ... .. ..... . . . . . ..... 50°C
Where water pressure exceeds 500kPa, a pressure reducing device is required to be installed Note that water .
pressure overnight can reach 150% of the daytime pressure.
Note: Installation of aerators containing flow regulators: Upon re-installation, the aerator should be tightened
with an aerator key to prevent removal by hand.
Note: Ceramic Cartridges: Warranty claims will not b honoured where the ceramic cartridge has e
malfunctioned due to the presence in the water supply of:
• Copper tube piece sand, dirt or stones s,
• Thread tape
• Other objects not normally present in potable water s es. uppli
Do not remove the cartridge from the body as it has been pressure tested and tightened to a
specific torque.
Before attempting any work involving ains water supply lines, ensure the water supply is shut off. m
Stop valves (preferably with filters) must be used when installing your Oliveri mixer to allow isolation (not
supplied with mixer). Failure to do so where required will void warranty.
This mixer tap is already pre-a embled and tested. Do not dis mble, as this may void the warranty. ss asse
Thi mixer tap must be installed in a ordance with these instructions. s cc
O veri Solutili ons Pty Ltd ABN 12 007 551 886
51 Naweena Rd, Rege y Park SA nc 5010 P 08 8348 6444 E sales@o eri.coliv m.au
Issue Date 12/03/ 022 3 Revision Number: V1.0
VE570CR / VE570MB / VE570BN
CARE & MAIN CE TENAN
Clean with a soft cloth and warm soapy water as nece ary - rin and dry after cleaning. Under no ss se
circumstances should abrasive or acid based cleaning products be used.
WA TY RRAN
PRODUCT CO ONENTMP DOMESTIC USE CO ERCIAL USEMM
Kitchen Tapware
Venice
Car idgetr 10 years replaceme pa s,nt rt
1 year labour
7 years replaceme pa s,nt rt
1 year labour
Body 7 years replaceme pa s,nt rt
1 year labour
1 years replaceme pa s,nt rt
& labour
Finish (chrome) 5 CRVE 70 7 years replacement pa s, rt
1 year lab rou
1 year replacement parts
& labour
Finish (Other) 5 N,VE 70B
VE570MB
5 years replacement pa s,rt
1 year lab rou 1 year replacement parts
& labour
Subject to the terms contained in the full warranty information available at https://oliveri.com.au ervice-and- /s
warranty, where a genuine manufacturing defect arises within the warranty period Oliveri will, at its election,
repair the defect or replace the product.
This warra y does not cover against n mal wear and will be vo ed if the product is misused nt or id
o installed in accordance with these instructions. r not Note: Fitting spout-attached devices, including
water filters, to this mixer will void warranty.
Our good co with guarantees that cannot be excluded under the Australian Consumer Law. You are s me
entitled to a replacement or refund for a major failure and for compen tion for any other reasonably sa
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
SERVICE
If the problem represents a danger, or damage to property may occ , immediately shut off the ur
water s ly. upp If the mixer tap require servicing, pl se contact your plumber (preferably the one who s ea
installed it). Most problems occur due to contaminated supply lin or water pressure exceeding 500k . es Pa
Unscrew and clean the spout aerator periodically - especially if you notice a drop in water pressure.
If the Plumber / Insta er is satisfied that the pr lem i t e tll ob s no du o poor insta all tion, contact Oliveri’ minated s no
Warranty Service Agent for a istance on: ss
Ph: (08) 8348 6444 (choose the after sa esl service & wa an rr ty op onti )
E il: warranty@oliveri.com.au ma
For full warranty information visit: h ps://ott liveri.com.au/service-and-wa anty rr
If a warranty service call fi s thand t the spout does not have a genuine manufacturing fault, our
Warranty Service ent reser s the ri t to pass on any call-out fee to the householder. Ag ve gh
Insta ation ll Inst ctionsru
Tec icalhn Data
Right Angle Mixer
INSTA ATION IN RUCTIONS LL ST
General Note: This product is to be installed by a licensed plumber, installation must comply with
AS/NZS 3500 and local plumbing c es. od
Pressures & Temperatures
Maximum Hydrostatic Pressure – 500 k . (As per AS/NZS ). Pa 3500
Note: AS/NZS 3500.1-2003 (Clause 3.3.4) states that “Provision shall be made to ensure that the
maximum static pressure at any outl , et other than a fire service outlet, within a building does
not exceed 500 kPa.
Note: Press es above 500kPa can cause damage from water hammer, reduced life of ap iances, ur pl
taps a fit ngs, and cause excessive ise in the system. nd ti no
Minimum Hydrostatic Pr sure – 100 k . The Maximum operating temperature for the mixer tap is 65 °es Pa C.
Please ensure that the nes are shed prior to installa on as co aminates in the water can li flu ti nt
damage the ceramic ca e, flow regulator and also affect the perf mance of the Mixer. rtridg or
1.
Remove pro ct pac gi and check for damage, if the pr ct is damaged do du from ka ng odu
no nd put insta all return to store of rchase.
2.
T
he WELS compliant aerator has been pre-a e led into the mixer ss mb outlet. To c ly with WELS omp
the flow re lator st remain in place.gu mu
3.
Ensure pr ct is c lete as per exploded drawing.odu omp
4.
A single m hole is re ired in the ting su ace35m qu moun rf
.
5.
The maximum mo ting su ace thickness ca t e eed 37 mm.un rf nno xc
6.
Ensure bench s ling washer (A) is in place on base of Mixer. Screw the Mixer Tails (C) into base of the ea
Mixer being careful to avoid damage to the o’ring seals, the Mixer Tails are colour coded,
red for hot
and blue for cold, the Mixer base inlet holes are stamped with ‘H’ for hot and ‘C’ for cold.
7. Screw Threaded Rod (D) into base of er. Mix
8. Feed the Mixer Ta s (C) thr h the m ting su ace, each end alternately and sition the mixer il oug oun rf po
on the mounting su ace ensuri the S Washer (A) is siti ed co ectly .rf ng ealing po on rr
9. Feed Mixer Ta s, each alternately through Stabiliser Plate (D) if s lied.il upp
10. Slide Rubber Horse Shoe (E) onto Threaded Rod (D) followed by Metal Horse Shoe Plate (F).
N.B The Mixer Tails should be positioned towards the user and the Fixing Bolt to the back.
11. Using Lock Nut (G) tighten the Mixer to mounting su ace h s, rf wit upplied tool (H).
12.
Connect Mixer Tails to mains water supply ne. li
13.
Ensure the Mixer Tails are not kinked, bent, stretched or twisted when assembling to the
mains water supply. The Mixer Tail connection between the Mixer and the water supply
must have a natural c ve. ur
14.
Ensure Mixer Tails are not exposed to abr ions, corrosive agents or the ke. as li
15.
It is rec ended that In-Line F ters be insta ed to ensure a cleaner flow of water to the Mixeromm il ll
.
TO THE CONSUMER
1. The Mixer is only to be cleaned with warm soapy water and soft . a cloth
2.
Issue Date 12/03/2023 Revision Number: V1.0
Under no circumstances should any abrasive, cream or acid-based cleaning agents be used, as these
types of cleaners can damage th finish, cartridge, seals and Mixer aerator. e
Installation Instructions
Max 37
C
D
E
F
G
A
Braided flexible hoses
must be inspected
every 12 months for
warning signs of failure
including bulging, rust
spots, wear, moisture,
snapped threads,
kinking, water staining,
general corrosion or
discolouration.
Mixer tails showing any
signs of the above
mentioned warning
signs must be replaced
immediately.
H
B
Especificaciones del producto
| Marca: | Oliveri |
| Categoría: | Grúa |
| Modelo: | VE570FBN |
¿Necesitas ayuda?
Si necesitas ayuda con Oliveri VE570FBN haz una pregunta a continuación y otros usuarios te responderán
Grúa Oliveri Manuales
17 Septiembre 2024
17 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
12 Septiembre 2024
Grúa Manuales
- Grúa IKEA
- Grúa Etna
- Grúa Inventum
- Grúa Smeg
- Grúa KitchenAid
- Grúa Teka
- Grúa Miomare
- Grúa Ernesto
- Grúa CDA
- Grúa Stiebel Eltron
- Grúa Elba
- Grúa Grohe
- Grúa Franke
- Grúa Nodor
- Grúa Delta
- Grúa Schütte
- Grúa Elkay
- Grúa Caple
- Grúa Quooker
- Grúa Brita
- Grúa ZLine
- Grúa Hansgrohe
- Grúa Lynx
- Grúa Empire
- Grúa Moen
- Grúa Aloni
- Grúa WillieJan
- Grúa Sani-Lav
- Grúa Mizzo
- Grúa Brauer
- Grúa Fala
- Grúa Lomazoo
- Grúa Livarno Lux
- Grúa Billi
- Grúa Deante
- Grúa Omnires
- Grúa Zip
- Grúa Viidako
- Grúa Curaqua
- Grúa Waltec
- Grúa Sussex
- Grúa Fantini
- Grúa Rogerseller
- Grúa Axor
- Grúa Gessi
- Grúa Graff
- Grúa Zurn
Últimos Grúa Manuales
6 Octubre 2024
2 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024