Omnitron Systems FlexPoint Manual de Usario

Omnitron Systems reproductor multimedia FlexPoint

Lee a continuación 📖 el manual en español para Omnitron Systems FlexPoint (1 páginas) en la categoría reproductor multimedia. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/1
Warning
The operating description in this Instruction Manual is
for use by qualied personnel only. To avoid electrical
shock, do not perform any servicing of this unit other
than that contained in the operating instructions, unless
you are qualied and certied to do so by Omnitron
Systems Technology, Inc.
Caution
All user-required operations can be performed without
opening the unit. Never attempt to open or remove the
cover or tamper with the unit.
Warranty
This product is warranted to the original purchaser
against defects in material and workmanship for a period
of TWO YEARS from the date of shipment. A LIFETIME
warranty may be obtained by the original purchaser
by REGISTERING this product with Omnitron within
90 days from the date of shipment. TO REGISTER,
COMPLETE AND MAIL OR FAX THE REGISTRATION
PORTION OF THIS INSTRUCTION MANUAL TO THE
INDICATED ADDRESS. Or you may register your
product on the internet at http://www.omnitron-systems.
com. During the warranty period, Omnitron will, at its
option, repair or replace a product which is proven to
be defective.
For warranty service, the product must be sent to
an Omnitron designated facility, at Buyer’s expense.
Omnitron will pay the shipping charge to return the
product to Buyer’s designated US address using
Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects
resulting from improper or inadequate use and/or
maintenance of the equipment by Buyer, Buyer-supplied
equipment, Buyer-supplied interfacing, unauthorized
modications or tampering with equipment (including
removal of equipment cover by personnel not specically
authorized and certied by Omnitron), or misuse, or
operating outside the environmental specication of the
product (including but not limited to voltage, ambient
temperature, radiation, unusual dust, etc.), or improper
site preparation or maintenance.
No other warranty is expressed or implied. Omnitron
specifically disclaims the implied warranties of
merchantability and tness for any particular purpose.
Exclusive Remedies
The remedies provided herein are the Buyer’s sole and
exclusive remedies. Omnitron shall not be liable for any
direct, indirect, special, incidental, or consequential
damages, whether based on contract, tort, or any
legal theory.
User Warranty Registration
Please register on-line @ http://www.omnitron-systems.com or complete both sides
and mail or fax this registration form to:
FlexPoint Type: 10/100, Fiber Type:_______Connector: _______
Model: _________________________________________________
Serial Number: ______________ Purchase Date: ______________
Purchased From: _________________________________________
Address: ______________________________________________
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Comments and Suggestions: _______________________________
______________________________________________________
______________________________________________________
Please complete both sides of this form
LED Indicators:
LED Color Description
Power: Yellow Power applied
UTP Auto: Green Auto-Negotiation enabled
UTP FDx: Green Full-Duplex detected
UTP Link: Green Link / Data received
UTP 10: Yellow 10 Mbps link detected
UTP 100: Green 100 Mbps link detected
Fiber FDx: Green Full-Duplex selected
F/O Link: Green Link / Data received
Switches:
Description Function
1- UTP Crossover: Straight / Crossed
2- UTP Auto: Auto-Negotiation / Manual
3- UTP 10/100: 10 Mbps / 100 Mbps
4- UTP Duplex: Full-Duplex / Half-Duplex
5- Fiber Duplex: Full-Duplex / Half-Duplex
Technical Support:
For help with this product, contact our Tech. Support:
Phone: (949) 250-6510
Fax: (949) 250-6514
Address: Omnitron Systems Technology, Inc.
38 Tesla
Irvine, CA 92618 USA
E-mail: support@omnitron-systems.com
URL: http://www.omnitron-systems.com
Form: 040-04340-001E 10/13
2. When used in a standalone conguration, this product
must be used with a Listed Direct Plug-In Power Unit
marked “Class 2” and rated at 9VDC, 1 Amp.
WARNING!
Before inserting the Power Adapter, verify that the power
on the unit is appropriate for your AC line voltage source.
3. To power the unit using a DC power source, prepare
a power cable using a two conductor insulated wire
(not supplied) with a 14 AWG gauge minimum. Cut the
power cable to the length required. Strip approximately
3/8 of an inch of insulation from the power cable wires.
Connect the power cables to the unit by fastening the
stripped ends to the DC power connector. Connect the
power wires to the DC power source. The Power LED
should indicate the presence of power.
Installation Procedure:
1. Configure the appropriate 10/100 DIP-Switch
settings.
2. Connect the RJ-45 port via a Category 5 or better
cable to a 10BASE-T or 100BASE-TX Ethernet device.
3. When using xed ber port models, connect the
appropriate multimode or single-mode ber cable to
the ber port of the installed module. It is important to
ensure that the transmit (Tx) is attached to the receive
side of the device at the other end and the receive (Rx)
is attached to the transmit side.
4. When using a 10/100 SFP model, insert the SFP
Fiber transceiver into the Port 1 SFP receptacle on the
10/100.
NOTE: The release latch of the SFP Fiber transceiver
must be in the closed (up) position before insertion.
User Warranty Registration
Please register on-line @ http://www.omnitron-systems.com or complete both sides
and mail or fax this registration form to:
Omnitron Systems Technology, Inc.
38 Tesla
Irvine, CA 92618, USA
Fax: (949) 250-6514
Name: _________________________________________________
Company: ______________________________________________
Address: ______________________________________________
______________________________________________
City: ___________________ State: _______ Zip Code: ________
Country: _______________________________________________
Phone: ____________________ Fax: _______________________
E-mail: _________________________________________________
Please complete both sides of this form
FlexPoint™
10/100 User Instructions
Description:
The FlexPoint 10/100 is a modular 10BASE-T or
100BASE-TX UTP to 100BASE-FX fiber media
converter featuring a 10/100 auto-sensing RJ-45 port.
The available models are shown below:
Model Dual Fiber Type Max Distance Connector
4340 1310 nm (MM) 5 km SC
4341 1310 nm (SM) 30 km SC
4342 1310 nm (MM) 5 km ST
4343 1310 nm (SM) 30 km ST
4344 1310 nm (SM) 60 km SC
4345 1310 nm (SM) 60 km ST
4347 1550 nm (SM) 85 km SC
4349 1550 nm (SM) 120 km SC
4359 SFP - LC
Model Single Fiber Type Max Distance Connector
4357-1 Tx13/Rx15 (SM) 20 km SC
4357-2 Tx15/Rx13 (SM) 20 km SC
About this Manual:
This document supports revision “3.x” of the FlexPoint
10/100. Please refer to the serial number label on
the FlexPoint 10/100 for the revision number of your
product.
Applying Power:
1. This product should only be used with Omnitron
supplied AC power supply model numbers 9113-PS
[US] or 9115-PS [Universal].
Switch Settings:
RJ-45 Crossover Switch
When the RJ-45 port is set to auto-negotiation, the
Auto-Crossover functionality is enabled and the RJ-45
Crossover Switch is disabled. When the RJ-45 port is
set to manual operation, the RJ-45 Crossover Switch
is enabled. The switch provides a convenient way to
connect to different devices and cables types.
UTP Auto/Man Switch
Setting the switch to “Auto” (factory default) enables the
RJ-45 port to automatically determine the speed and
duplex mode of the connected device. If the connected
device cannot provide the proper signal to indicate its
mode of operation, set the switch to “Man.”
UTP 10/100 Switch
When the “Auto/Man” switch is in “Man” position, the
“UTP 10/100” switch determines the speed of the RJ-45
port. When set to “100” (factory default), the RJ-45 port
will operate at 100 Mbps. When set to “10” the RJ-45
port will operate at 10 Mbps.
UTP FDX/HDX Switch
When the “Auto/Man” switch is in “Man” position, the
“UTP FDX/HDX” switch determines the duplex mode for
the RJ-45 port. When set to “FDX” (factory default), the
RJ-45 port operates in Full-Duplex. When set to “HDX”,
the RJ-45 port operates in Half-Duplex.
Fiber FDX/HDX Switch
Setting the “Fiber FDX/HDX switch to “FDX” sets the
ber port to Full-Duplex (factory default). Setting the
“Fiber FDX/HDX switch to “HDX” sets the ber port to
Half-Duplex.

Especificaciones del producto

Marca: Omnitron Systems
Categoría: reproductor multimedia
Modelo: FlexPoint

¿Necesitas ayuda?

Si necesitas ayuda con Omnitron Systems FlexPoint haz una pregunta a continuación y otros usuarios te responderán


reproductor multimedia Omnitron Systems Manuales

Omnitron Systems

Omnitron Systems iConverter Gx AN Manual de Usario

13 Septiembre 2024
Omnitron Systems

Omnitron Systems FlexPoint GX/T Manual de Usario

13 Septiembre 2024
Omnitron Systems

Omnitron Systems FlexPoint Manual de Usario

8 Septiembre 2024

reproductor multimedia Manuales

Últimos reproductor multimedia Manuales

Fantec

Fantec 16132 Manual de Usario

26 Octubre 2024
Eminent

Eminent EM7167 Manual de Usario

18 Octubre 2024
Google

Google Chromecast Audio Manual de Usario

17 Octubre 2024
Sanyo

Sanyo HMP200 Manual de Usario

14 Octubre 2024
LG

LG LVC-C553 Manual de Usario

8 Octubre 2024
Jensen

Jensen CAR140MW Manual de Usario

8 Octubre 2024
LG

LG RH399M Manual de Usario

8 Octubre 2024
LG

LG VLC8610W3K Manual de Usario

8 Octubre 2024
LG

LG V8814P Manual de Usario

8 Octubre 2024
Dune

Dune HD Base 3D Manual de Usario

7 Octubre 2024