Overmax Multipic 3.1 Manual de Usario

Overmax Proyector Beamer Multipic 3.1

Lee a continuación 📖 el manual en español para Overmax Multipic 3.1 (88 páginas) en la categoría Proyector Beamer. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/88
English
Warning:
Before using this projector, please read the manual carefully. Any wrong
operation may cause electric shock or fire. Please comply with the following
instructions when using and/or repairing the projector.
1. Clean
When clean this projector, please unplug the power cable and use the wet cloth
not the cleanser.
2. Accessories
Please use the recommended accessories or the projector maybe damaged.
3. Using environment
Do not place the projector on any wet environments.
4. Installation
Please place this projector on a stable surface
5. Ventilation
For best performance, please clean the filter once a month.
6. Power
Before plug in the power, please make sure the voltage of your area matches
this projector (220V or 110V).
7. Ground wire
The three pin plug is the ground wire of this projector.
8. Protect the power cable
Make sure the power cable is in perfect working condition before using it.
9.
Thunder
When there is thunder or not using
the projector for a long period of time , unplug the power cable.
10.
Repair
Due to high voltage, do not open or try to repair the projector by yourself.
Refer to a professional technician if repair is needed.
11. Heat
Make sure not to put this projector near any heating devices. That may
shorten the life span of the projector.
English
About the installation
In order to improve this projector's life span, do not place it on a wet surface.
Do not put the projector under the direct sun light.
Projector working temperature: 0°C - +50 °C
Projector store temperature : -20°C - +50 °C
Do not block the ventilation-window of the projector. If the projector
interior temperature is too hot, it will be automatically shut down. This will
protect the projector. To prevent over heating the projector, please clean
the filter once a month.
About turn on/off the projector
To turn on the projector, connect the power cable, then press the "power" key
on the panel. It will take couple of minutes before the lamp works normally.
To turn off the projector, press the "power" key again. The lamp will shut
off while the fan will still working for a little longer. The projector will shut off
automatic--ally when the fan stops. DO NOT unplug the power cable before
turn off the projector.
Warning:
The fan is to keep the projector's temperature low. It will turn on when projector
is turned on. The speed of the fan is according to the heat of the projector. Do
not unplug the power cable when the projector is not turned off and the fan
is still working. If the fan stops working, the projector may be damaged due to
overheat.
Troubleshooting
Problem
The possible causes
When turn on the
power, the indicator light
does not work
power cable did not connect well.
the power switch fuse is broken
The remote control
cannot turn on the
projector.
the power switch is turned off
the remote control has no batteries or
the batteries are low
the remote control does not aim at the
IR
point
No Image
the choice of the input source may not be
correct
no input signal
the input cable is not connected
if under PC mode, the PC output frequency is
not 50-60Hz. Make sure that the PC output is
connected with the projector.
Auto-off after use some
times
the projector ventilation is blocked
the voltage is not stable
the projector is overheated, check if the fan
is broken

Especificaciones del producto

Marca: Overmax
Categoría: Proyector Beamer
Modelo: Multipic 3.1

¿Necesitas ayuda?

Si necesitas ayuda con Overmax Multipic 3.1 haz una pregunta a continuación y otros usuarios te responderán