Ozito EPP-750 Manual de Usario

Ozito máquina de aserrar EPP-750

Lee a continuación 📖 el manual en español para Ozito EPP-750 (8 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY

PLEASE TELEPHONE OUR CUSTOMER SERVICE

HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the

original date of purchase and is intended for DIY (Do It Yourself)

use only. If a product is defective it will be replaced in accordance

with the terms of this warranty. Warranty excludes consumable

parts, for example: guide bar, chain and included accessories.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other

than that speciﬁed on the tool.

• If the tool shows signs of damage or defects caused

by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the

instruction manual.

• If the tool is disassembled or tampered with in any way.

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/New Zealand (Head Ofﬁce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The beneﬁts provided under this warranty are in addition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded

at law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Generally you will be responsible for all costs associated with

a claim under this warranty, however, where you have suffered

any additional direct loss as a result of a defective product you

may be able to claim such expenses by contacting our customer

service helpline above.

TELESCOPIC

POLE PRUNER

750W 200MM (8”)

INSTRUCTION MANUAL

SPECIFICATIONS

Power: 750W

Chain Speed: 11 meters/second

No Load Speed: 6,000/min

Max Cutting Width: 180mm

Guide Bar Length: 200mm (8”)

Oil Tank Capacity: 60ml

Telescopic Range: 1.85 – 2.80m

Weight: 3.82kg

EPP-750

WHAT’S IN THE BOX

WARRANTY

ozito.com.au

0817

Shoulder Strap

Telescopic Pole Pruner

Chain

Guide Bar

Guide Bar Cover

Additional Handle

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

1. CHAIN & BAR

CAUTION!: THE CHAIN HAS SHARP EDGES. FOR YOUR

OWN SAFETY, PLEASE USE WORK GLOVES.

KNOW YOUR PRODUCT SETUP & PREPARATION

TELESCOPIC

POLE PRUNER

1. Chain

2. Guide bar

3. Chain sprocket cover

4. Motor housing

5. Telescopic shaft lock

6. Main shaft

7. Additional handle

8. Shoulder strap attachment

9. Oil tank cap

10. Chain tension dial

11. Chain cover lock

12. Switch lock

13. On/off trigger switch

14. Cord retainer

15. Chain sprocket

16. Bucking spikes

17. Rear handle

Fitting the guide bar and chain

1. Loosen the chain

cover lock and

remove the chain

sprocket cover.

2. Place the chain in the

groove of the guide bar

as shown. Refer to the

image printed on the

guide bar that indicates

the direction that the

chain should face.

3. Place the guide bar and

chain onto the mount,

ensuring that the chain

sits around the chain

sprocket.

4. Re-mountandnger-

tighten the side cover

with the chain cover

lock.

NOTE: Only tighten the chain cover locking knob securely once the

chain tension has been adjusted (see: Tensioning the chain).

WARNING!: ENSURE THE TOOL IS

DISCONNECTED FROM THE POWER SUPPLY

BEFORE ASSEMBLY.

IMPORTANT!: IF THE CHAIN IS INSTALLED

BACKWARDS (CHAIN CUTTERS ARE FACING IN THE

OPPOSITE DIRECTION OF ROTATION) THE POLE

PRUNER WILL VIBRATE EXCESSIVELY AND NOT CUT.

9 10 11 12 13

14 15 16

WARNING! NEVER START WORK UNLESS THE

CHAIN AND BAR ARE LUBRICATED.

3. SAW CHAIN LUBRICATION2. TENSIONING THE CHAIN

1. Place the telescopic

pole pruner on a level

surface.

2. Clean the area around the oil

tank cap and then open it.

3. Fill the oil tank with BAR AND

CHAIN OIL (not supplied) to

maximumllline.Donotoverll

in doing so, make sure that no

dirt gets into the oil tank. This will

ensure that the oil nozzle does

not clog.

4. Close the oil tank cap.

WARNING!: THE USE OF THE POLE PRUNER

WITHOUT BAR AND CHAIN OIL OR WITH AN OIL

LEVEL BELOW THE MINIMUM OIL LEVEL MARK WILL

RESULT IN DAMAGE TO THE CHAIN!

1. Loosen the chain cover

lock. Do not remove the

side cover.

2. Adjust the chain tension with the

chain tensioning dial. Turning

the dial CLOCKWISE increases

the chain tension, turning it

COUNTER-CLOCKWISE

decreases the chain tension.

3. For the correct chain tension,

rmlypulluponthechainatthe

middle of the top of the exposed

guide bar. When the chain is

pulled up to its highest point, the

bottom tip of the links should only

just stay in the track [middle of the

guide bar]

4. After the chain has been

accurately tensioned, lock

the guide bar in place with

the chain cover lock.

5. Check the tension again

afterafewminutesofcuttingandseveraltimesinthersthour

because the chain will lengthen as it breaks in. Adjust as you go. A

loose chain causes rapid wear to both the chain and the guide bar

and could derail causing a major safety hazard.

NOTE: Proper tension of the chain is extremely important and must be

checked before starting, as well as during any cutting operation. Taking

the time to make adjustments to the chain will result in improved

cutting performance and prolonged chain life.

5. To check the lubricating system, switch on the pole pruner and hold

it with the guide bar and chain above some light coloured paper

such as newspaper. A steadily increasing stain caused by oil spray

shows the lubricating system is working.

NOTE: Guide bar oil may leak if the tool is left for long periods. This is

normal. If the tool is to be left unused for an extended time, drain the

oilfromthetool.Rellbeforeuse.

CAUTION!: IF YOU TRY TO ROTATE THE CHAIN

TENSIONING ADJUSTMENT DIAL WHILST THE CHAIN

COVER LOCK IS TIGHT, IT WILL RESULT IN THE CHAIN

NOT LOOSENING AND POSSIBLE DAMAGE TO THE

MECHANISM.

MAX.

CAUTION!: THE CHAIN HAS SHARP EDGES. FOR YOUR

OWN SAFETY, PLEASE USE WORK GLOVES.

Especificaciones del producto

Marca:	Ozito
Categoría:	máquina de aserrar
Modelo:	EPP-750
Color del producto:	Wit
Peso.:	8800 g
Ancho:	224 mm
Profundidad:	276 mm
Altura:	330 mm
Material de la carcasa:	MDF
Interruptor encendido / apagado:	Ja
Tecnología de conectividad:	Bedraad
Tipo de fuente de energía:	AC
Energía promedio:	73 W
Control del volumen:	Draaiknop
Configuración del ecualizador:	Ja
Uso recomendado:	Universeel
Impedancia:	7 Ohm
Canales de salida de audio:	1.0 kanalen
Colocación de los altavoces:	Floor, Tabletop/bookshelf
Número de conductores:	2
altavoz de graves:	Ja
Rango de frecuencia:	38 - 35000 Hz
Sensibilidad:	107 dB
Tipo de altavoz:	2-weg
Amplificador:	Ingebouwd
Diámetro del altavoz de graves:	6 "
Número de controladores de woofer:	1
Diámetro hogetonenluidspreker:	1 "
Número de controladores de tweeter:	1
XLR en:	Ja
Ajuste del nivel de graves:	Ja
tweeter:	Ja
Ajuste de agudos:	Ja
Frecuencia de cruce:	2300 Hz
Clase de amplificador:	A/B
Entrada de 6,35 mm (1/4 de pulgada):	1