Ozito MCS-2355 Manual de Usario

Ozito maquina cortadora MCS-2355

Lee a continuación 📖 el manual en español para Ozito MCS-2355 (8 páginas) en la categoría maquina cortadora. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/8
METAL
CUT-OFF SAW
2300W
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 2300W
Input: 230 – 240V~50Hz
No Load Speed: 4,400/min
Wheel Max. Diameter: 356 x 3mm (14” x 1/8’’)
Arbour Size: 25.4mm
Cutting Angles: 0 – 45º Left,
0 – 15º Right
Max. Cutting
Capacities @90°: Round steel 130mm
Square steel 120mm
Rectangle steel 120x130mm
Angle steel 140x140mm
@45°: 90x100mm
Weight: 16.8kg
MCS-2355
STANDARD EQUIPMENT
3 YEAR REPLACEMENT WARRANTY*
Your product is guaranteed for a period of If 36 months from the original date of purchase.
a product is defective it will be replaced in accordance with the terms of this warranty. Warranty
excludes consumable parts, for example: valve adapters and accessories.
*This product is intended for DIY use only and replacement warranty covers domestic use.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other than that specified on the tool.
• If the tool shows signs of damage or defects caused by or resulting from abuse, accidents
or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
WARRANTY
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
ozito.com.au
Metal Cut-Off Saw & Cut-Off Wheel
Hex Key
1020
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY
YOU MUST RETURN THE PRODUCT TO YOUR NEAREST
BUNNINGS WAREHOUSE WITH YOUR BUNNINGS
REGISTER RECEIPT. PRIOR TO RETURNING YOUR
PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR
CUSTOMER SERVICE HELPLINE:
Australia: 1800 069 486
New Zealand: 0508 069 486
The benefits provided under this warranty are in addition to other rights and remedies which
are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to a
replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this warranty,
however, where you have suffered any additional direct loss as a result of a defective product
you may be able to claim such expenses by contacting our customer service helpline above.
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE
THE MODEL NUMBER AND DATE OF PURCHASE
AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE
WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS
YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
Your Metal Cut-Off Saw is used for cutting steel such as pipe, box
section, rectangular, angle iron and steel bars. The saw can cut
at angles from 0 to 45º left & 0 to 15º right, it features a three
position fence that permits an extended cutting range. The quick
release vice allows fast adjustment whilst the lock-off button
prevents accidental operation. It is intended for DIY use only.
WARNING! ENSURE THE TOOL IS TURNED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING OPERATIONS.
Securing The Base
WARNING! ALWAYS POSITION THE METAL CUT-OFF
SAW ON A STABLE & LEVEL SURFACE.
It is recommended to bolt the tool to a stable and level surface.
This will help prevent tipping over and potential personal injury.
Use two M10 bolts and nuts
(not supplied) in the anchor
points to secure it.
Depth stop
Note: Ensure that the depth stop is adjusted to the correct height
before commencing operation. The depth stop should be checked
and adjusted every time a new cut-off wheel is fitted.
WARNING! DO NOT REMOVE OR OPERATE WITHOUT
THE DEPTH STOP!
The adjustable depth stop is threaded into the base of the machine
at the rear. The travel of the cut-off wheel can be controlled by
raising and lowering the depth stop bolt. This feature is particularly
useful to prevent contact with the work bench surface when a new
cut-off wheel is fitted or to increase cut-off wheel travel as the
cut-off wheel wears.
1. Loosen the depth stop with the hex key supplied.
2. Increase or decrease the height of
the depth stop.
3. Tighten the depth stop knurled lock
nut with your fingers.
1. Vice Handle
2. Lower Guard
3. Cut-Off Wheel
4. Upper Guard
5. Rubber Feet
6. Carry Handle
7. Lock-Off Button
8. Trigger Switch
9. Main Handle
10. Vice
11. Hex Key Storage
12. Base Anchor Point
13. Quick Release Vice Lock
14. Fence
15. Base
16. Depth Stop
17. Base Anchor Point
18. Lock Down Pin
19. Spindle Lock Button
METAL CUT-OFF SAW
KNOW YOUR PRODUCT
1. ADJUSTMENTS
SETUP & PREPARATION
17
18
1
6 7 8 119 10
3 42
13141516
5
12
19
WARNING! THIS CUT-OFF SAW IS DESIGNED TO CUT
FERROUS METALS ONLY.
ONLINE MANUAL
Scan this QR Code with your mobile
device to take you to the online manual.
Adjusting the cutting angle
1. To change the cutting angle loosen the
two bolts securing the fence using the
hex key supplied.
2. Move the rear fence to the desired
angle using the scale as a guide.
3. Tighten the two bolts to secure the
fence in position.
WARNING! ONLY PERFORM ANGLE CUTS WHEN THE
FENCE IS SET AT THE MOST FORWARD POSITION
(REFER TO ADJUSTING THE FENCE).
Note: For accurate cuts, test the cutting angle on some similar
scrap material and adjust the angle to suit your requirements. The
scale is only a guide.
Adjusting the fence
The spacing between the vice and the fence as supplied is
170mm.
WARNING! THE FENCE MUST BE INSTALLED
SECURELY BEFORE USE TO PREVENT THE WORK PIECE
MOVING AND POTENTIALLY CAUSING INJURY.
When cutting wider materials the rear fence will need to be
adjusted to the rear position. When cutting narrow work pieces the
fence should be positioned in the most forward position.
1. To adjust, loosen and remove the two
bolts securing the fence using the Hex
key.
2. Move the fence backwards or
forwards to one of the other two
fixing positions.
3. Tighten the two bolts to secure the
fence in position.
WARNING! ALWAYS USE THE VICE TO CLAMP THE
WORK PIECE. ENSURE ANY OVER-HANGING PORTIONS
OF THE WORK PIECE ARE PROPERLY SUPPORTED &
LEVEL WITH THE TABLE OF THE SAW.
WARNING! NARROW WORK PIECES MAY NOT BE
SECURED SAFELY WHEN USING AN INTERVAL TOO
WIDE FOR THE FENCE. ENSURE THAT THE FENCE
IS SET TO THE MOST FORWARDS POSITION THAT
ALLOWS THE WORK PIECE TO BE CLAMPED SECURELY.
Adjusting the vice
WARNING! ENSURE THAT THE VICE SECURING BOLTS
AND VICE ARE FIRMLY TIGHTENED BEFORE USE TO
PREVENT THE WORK PIECE MOVING AND RISK OF
PERSONAL INJURY.
WARNING! THE VICE & FENCE MUST ALWAYS BE
SECURED PROPERLY BEFORE CUTTING. ALWAYS
SECURE THE MATERIAL BEFORE PERFORMING A CUT,
FAILURE TO DO SO MAY RESULT IN INJURY.
WARNING! REFER TO THE CUTTING CAPACITY
SPECIFICATIONS FOR THE SAW. DO NOT CUT
MATERIALS THAT EXCEED THE CUTTING CAPACITY OF
THE CUT-OFF SAW.
WARNING! NEVER CUT MORE THAN ONE WORK PIECE
AT A TIME. DO NOT STACK MORE THAN ONE WORK
PIECE ON THE MACHINE BASE AT A TIME.
The vice can be
adjusted quickly
by lifting the quick
release vice lock and
pushing forward or
pulling back on the
vice handle.
1. Place your work piece in between the fence and vice.
2. Lift the quick
release vice lock
and push the vice
forward.
3. Once the vice hits the work piece
push down the quick release vice
lock.
4. Rotate the vice handle in a clockwise
direction to secure the work piece in
position.
5. To remove an object from the vice,
rotate the vice handle in an anti-
clockwise direction until the vice jaws
are loose. The work piece can now be
removed.
Note: The quick release vice lock cannot be lifted until the vice
jaws have been loosened.
a.
b.

Especificaciones del producto

Marca: Ozito
Categoría: maquina cortadora
Modelo: MCS-2355

¿Necesitas ayuda?

Si necesitas ayuda con Ozito MCS-2355 haz una pregunta a continuación y otros usuarios te responderán


maquina cortadora Ozito Manuales

Ozito

Ozito MCS-2355 Manual de Usario

6 Octubre 2024

maquina cortadora Manuales

Últimos maquina cortadora Manuales

Eldom

Eldom Sliss KR350 Manual de Usario

26 Octubre 2024
RGV

RGV Desy AF 220 AM Manual de Usario

26 Octubre 2024
RGV

RGV Desy AF 275 F Manual de Usario

26 Octubre 2024
Royal Catering

Royal Catering RCKS-3 Manual de Usario

16 Octubre 2024
Royal Catering

Royal Catering RCKS-2 Manual de Usario

16 Octubre 2024
Royal Catering

Royal Catering RCAM-250PRO Manual de Usario

15 Octubre 2024
Royal Catering

Royal Catering RCAM-250EXPERT Manual de Usario

15 Octubre 2024
Royal Catering

Royal Catering RCAM-250E Manual de Usario

14 Octubre 2024
Princess

Princess Classic Multi Food Slicer 492977 Manual de Usario

10 Octubre 2024
Severin

Severin AS 3914 Manual de Usario

9 Octubre 2024