Ozito PXBLTS-018 Manual de Usario

Ozito No categorizado PXBLTS-018

Lee a continuación 📖 el manual en español para Ozito PXBLTS-018 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/8
STANDARD EQUIPMENT
5 6
mm 00 in.
10
1/2
20
5 6
PXBLTS-018
INSTRUCTION MANUAL
SPECIFICATIONS
Input: 18V
No Load Speed: 10,000 - 30,000/min
Collet Size: 6.35mm & 8mm
Max. Cutter Size: 28mm
Dust Port Size: Ø35mm
Weight: 1.84kg
ozito.com.au
0722
Brushless Trim Router
Dust Extraction Port, Parallel
Guide & Trimmer Guide
8mm Collet, Template Guide
Bushing, Compass Point & 2 x
Spanners (22 & 13mm)
TRIM
ROUTER
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU
MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS
WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE
OUR CUSTOMER SERVICE HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
WARRANTY
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL
NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER
SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND
ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE
WARRANTY POLICY OR PROCEDURE.
OZITO INDUSTRIES PTY. LTD. 25 Fox Drive, Dandenong South, Victoria, Australia 3175.
The benets provided under this warranty are in addition to other rights and
remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded at law. You are entitled to
a replacement or refund for a major failure and for compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure
does not amount to a major failure.
Generally you will be responsible for all costs associated with a claim under this
warranty, however, where you have suffered any additional direct loss as a result of
a defective product you may be able to claim such expenses by contacting our
customer service helpline above.
WARNING
The following actions will result in the warranty being
void.
• If the tool has been operated on a supply voltage other than that specied
on the tool.
• If the tool shows signs of damage or defects caused by or resulting from
abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction manual.
• If the tool is disassembled or tampered with in any way.
5 YEAR REPLACEMENT WARRANTY
Your Product is guaranteed for a period of 60 months from the original date of
purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it
will be replaced in accordance with the terms of this warranty. Lithium Ion
batteries and chargers are covered by a 36 month
warranty and are excluded from the warranty extension. Warranty excludes
consumable parts.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
5 6
1. Lock Off Switch
2. On/Off Switch
3. Sure Grip Handle
4. Battery Seating
5. Speed Control Dial
6. Trim Router Base
7. Depth Fastening Screw
8. Cut Depth Scale
9. Spindle
10. Spindle Nut
11. Spindle Lock
12. Dust Extraction port
13. Height Adjustor
14. Guide Mount Screw
15. Baseplate
16. Clear Safety Guard
This tool is compatible with all batteries & chargers from the Ozito PXC range.
For optimal performance, we recommend the use of a 3.0Ah battery or
higher to operate this PXC Trim Router.
BRUSHLESS TRIM ROUTER
BATTERY & CHARGER
KNOW YOUR PRODUCT
1. ASSEMBLY
SETUP & PREPARATION
Installing A Router Bit
When using the trim router, only use router bits that:
• are suitable for cutting wood or plastic,
• has a suitable shank diameter for the collet mounted (collet size:
6.35mm & 8mm),
• has a maximum diameter of 28mm,
• are suitable for the router’s speed (n0 = 10,000-30,000/min).
1. Remove the trim router base from the
router unit.
2. Place the smaller supplied spanner on
the spindle and use the large spanner to
loosen the collet nut.
Note: If a different collet size is required,
remove the collet nut entirely and replace
the collet. Re-attach the collet nut but don’t
tighten it all the way.
3. Fully insert the shaft of the router bit (not
supplied) into the collet.
4. Press and hold down the spindle lock
while tightening the collet nut with your
ngers.
5. Release the spindle lock and then use the
2 spanners to fully tighten the collet nut.
WARNING! THE SPINDLE LOCK IS NOT ALLOWED
TO BE USED FOR TIGHTENING WITH THE SPANNER.
TIGHTEN THE CLAMP NUT USING THE TWO
SPANNERS.
mm 00 in.
10
1/2
20
mm 00 in.
10
1/2
20
mm 00 in.
10
1/2
20
mm 00 in.
mm 00 in.
10
1/2
1
4 5
2
7
3
13
6
8
9
1416 15
11 1012
WARNING! ENSURE THE TOOL IS SWITCHED
OFF AND THE BATTERY IS REMOVED BEFORE
PERFORMING ANY OF THE FOLLOWING TASKS.
WARNING! WEAR GLOVES WHEN HANDLING
ROUTER BITS AS THEY CAN BE SHARP AND/OR
HOT TO THE TOUCH AFTER USE.
WARNING! ONLY USE THE ROUTER UNIT WITH A
COMPATIBLE BASE. USING IT WITHOUT A BASE
OR WITH AN INCOMPATIBLE BASE MAY RESULT IN
SERIOUS INJURY.
Attaching The Trimmer Guide
The trimmer guide allows you to
trim off precise amounts of material
from the edge of a workpiece.
1. Loosen the guide mount screw.
2. Slide the trimmer guide arm
between the washer and router
base.
Note: The height of the trimmer
guide should be just below the
router bit when it is completely
lowered.
3. Tighten the guide mount screw to lock the
guide in place.
Adjusting The Trimmer Guide
1. Loosen the trimmer locking bolt.
2. Adjust the trim depth by rotating
the horizontal adjustment knob.
Rotate the knob clockwise for a
larger trim.
3. Tighten the trimmer locking bolt to set the
distance in place.
2. EDGE TRIMMING
WARNING! NEVER USE THE TRIM ROUTER WITHOUT
THE SAFETY GUARD FITTED.
Attaching The Safety Guard
1. Use a screwdriver (not supplied) to
remove the screw on the trim router base.
2. Slide the safety guard into position and
replace the screw to lock it in place.
Attaching & Removing The Trim Router Base
1. Loosen the depth fastening screw.
2. Slide the router into the
router base.
3. Tighten the depth fastening
screw.
4. To remove the base, loosen the depth fastening screw and pull the base
off the router.
Fitting A Battery
1. Slide the battery into the tool base until it
clicks into place.
2. Hold down the battery release
button and then slide the battery
out.
a.
b.

Especificaciones del producto

Marca: Ozito
Categoría: No categorizado
Modelo: PXBLTS-018

¿Necesitas ayuda?

Si necesitas ayuda con Ozito PXBLTS-018 haz una pregunta a continuación y otros usuarios te responderán


No categorizado Ozito Manuales

Ozito

Ozito PXBSPS-180 Manual de Usario

6 Octubre 2024
Ozito

Ozito SSH-240 Manual de Usario

6 Octubre 2024
Ozito

Ozito PXTLS-905 Manual de Usario

3 Octubre 2024
Ozito

Ozito ADWH-913V Manual de Usario

2 Octubre 2024
Ozito

Ozito PXBLEK-418 Manual de Usario

24 Septiembre 2024
Ozito

Ozito DMC-1000 Manual de Usario

21 Septiembre 2024
Ozito

Ozito PXMFTS-018 Manual de Usario

19 Septiembre 2024
Ozito

Ozito PXBCSS-184 Manual de Usario

15 Septiembre 2024
Ozito

Ozito PXPPS-1820 Manual de Usario

14 Septiembre 2024
Ozito

Ozito PXNGS-218 Manual de Usario

14 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024