Ozito PXCCSS-018U Manual de Usario

Ozito máquina de aserrar PXCCSS-018U

Lee a continuación 📖 el manual en español para Ozito PXCCSS-018U (3 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

SPECIFICATIONS

Input: 18V DC

Idle Speed no: 2400 min¯

Bar Length: 250mm (10”)

Cutting Length Max.: 230mm

Chain Speed: 4.3m/s

Chain Pitch: 9.53mm (3/8”)

Chain Gauge: 1.1mm (.043”)

Oil Tank Capacity: 200ml

Weight: 3.0kg

WHAT’S IN THE BOX

Chainsaw

Battery & Charger

sold separately

CORDLESS

CHAINSAW

ORIGINAL INSTRUCTIONS

ozito-diy.co.uk

Guide Bar Cover

WARNING: BEFORE CLEANING YOUR CHAINSAW OR

CARRYING OUT ANY MAINTENANCE PROCEDURE,

MAKE SURE THE BATTERY REMOVED TO PREVENT

ACCIDENTAL STARTING.

CAUTION: ALWAYS WEAR GLOVES WHEN HANDLING

THE CHAIN AS IT IS VERY SHARP AND CAN CUT YOU

WHEN IT IS NOT MOVING.

Screwdriver

EH-Art. No.: 45.017.59 I-No.: 11016

MAINTENANCE TROUBLESHOOTING

ADDITIONAL SAFETY INSTRUCTIONS

Wear safety goggles

WARNING - To reduce the risk

of injury, user must read

instruction manual

Never expose the device to rain

Always hold the saw with both hands

Wear ear protectors

Maximum cutting length / chain speed

Unlock chain brake before putting into operation!

Store the battery only in dry rooms with anambient temperature

of +10 C to +40 C. Place only charged batteries in storage° °

(charged at least 40%).

Unlock chain brake before putting into operation!

Battery protection system

The tool is equipped with the battery protection system, which helps to ensure a long service

life.

The output power automatically cuts off during operation when the tool and/or battery are

placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull the

switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or immediately

after using the tool.

PXCCSS-018U

WARRANTY

1016

Adjusting the Chain Tension

1. Loosen the guide bar locking knob

slightly, by rotating it in an anti clockwise

direction.

2. Adjustment chain tension screw

CLOCKWISE to increase chain tension.

Turning screw COUNTERCLOCKWISE will

decrease amount of tension on the chain.

Adjust the chain tension screw for the

correct tension.

3 - 4mm gap is

the ideal tens nio

For the correct chain tension, pull up on the

chain from the top and middle of the exposed

guide bar. The bottom tip of the links should

only just stay in the track.

3. After the chain has been accurately

tensioned, lock the guide bar in place with

the guide bar locking knob.

Note: Proper tension of the chain is extremely important and must be checked before

starting, as well as during any cutting operation. Taking the time to make

adjustments to the chain will result in improved cutting performance and

prolonged chain life.

Maintaining the guide bar

1. Remove any sawdust from the guide bar, including the groove.

Oil and sawdust combine and emit a burning smell during operation if the blade is not

regularly cleaned.

2. Make sure that the oil port is not clogged. Grease the nose sprocket at the tip of the

guide bar.

3. Check for oil leakage and loose fastenings, especially those securing the handles and

the guide bar.

4. Reverse the guide bar every 8 working hours to ensure uniform wear. Check the guide

rails frequently and if necessary remove burrs and square up the rails using a at le.

Chain Sharpening

Chain File: 3.96mm (5/32”)

Chain Pitch: 9.53mm (3/8”)

Chain Gauge: 1.1mm (0.043”)

Sharpen the chain regularly to maintain

optimum performance of the saw. Signs of a

dull chain are:

• Thesawdustbecomespowder-like

• Extraforceisrequiredtoexecuteacut

• Thecutdoesnottrackinastraightline

• Increasedvibration

Sharpen each cutter using a round 3.96mm (5/32”) chain le. Keep the le level with the

top plate of the tooth. Always use outward strokes and maintain a 30° angle between the

chain and le. After sharpening, the cutters must all have the same width and length.

After every 3–4 uses get an authorised repair centre to professionally sharpen your chain.

They have the special tools necessary to ensure the correct cutting angles and depths.

LEFT HAND

CUTTERS

RIGHT HAND

CUTTERS

30°

Cleaning and storing

• Keepthehandlesfreeofgreasesothatyoucanmaintainarmgrip.

• Cleanthedeviceasrequiredwithadampclothand,ifnecessary,mildwashingup

liquid.

• Ifthechainsawisnottobeusedforanextendedperiodoftime

then you should remove the chain oil from the tank. Briey immerse the chain and

the cutter rail in an oil bath and then wrap them

in oil paper.

• Ensurethattheguidebarcoverisinplacewhenstoring.

CAUTION! ALWAYS DISCONNECT THE BATTERY BEFORE

CLEANING THE CHAINSAW.

CAUTION! NEVER IMMERSE THE UNIT IN WATER OR

OTHER LIQUIDS IN ORDER TO CLEAN IT.

CAUTION! STORE THE CHAINSAW IN A SAFE AND DRY

PLACE OUT OF THE REACH OF CHILDREN.

SPARE PARTS

DESCRIPTION OF SYMBOLS

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: enquires@ozito-diy.co.uk

The chainsaw is intended for felling trees and for cutting trunks, branches, wooden

beams, boards etc. and can be used for cross cuts and longitudinal cuts. It is not suitable

for cutting any materials other than wood.

The equipment is to be used only for its prescribed purpose. Any other use is deemed

to be a case of misuse. The user / operator and not the manufacturer will be liable

for any damage or injuries of any kind caused as a result of this. Please note that our

equipment has not been designed for use in commercial, trade or industrial applications.

Our warranty will be voided if the machine is used in commercial, trade or industrial

businesses or for equivalent purposes.

PROPER USE

Mayr/Product-ManagementWeichselgartner/General-Manager

explains the following conformity according to EU directives and norms for

the following product

Cordless Chain Saw PXCCSS-018U / Fast Charger PXCG-030U (Ozito)

2014/29/EU

2005/32/EC_2009/125/EC

2014/35/EU

2006/28/EC

X 2014/30/EU

2014/32/EU

2014/53/EC

2014/68/EU

90/396/EC_2009/142/EC

89/686/EC_96/58/EC

X 2011/65/EU

X 2006/42/EC

X Annex IV

Notied Body: TÜV SÜD Product Service GmbH - Riedlerstr. 65 - D-80339 München

Germany

Notied Body No.: 0123

Reg. No.: M6A 16 10 24192 01748

X 2000/14/EC_2005/88/EC

X Annex V

Annex VI

Noise: measured LWA

= 95,4 dB (A); guaranteed L

WA = 98 dB (A)

P = KW; L/Ø = cm

Notied Body: TÜV SÜD (0123)

2012/46/EU

Emission No.:

Standard references: EN 60745-1; EN 60745-2-13; EN 55014-1; EN 55014-2;

EN 61000-3-2; EN 61000-3-3; EN 60335-1; EN 60335-2-29; EN 62233; EN 62321

Landau/Isar, den 28.09.2016

First CE: 16 Archive-File/Record: NAPR015299

Art.-No.: 45.017.59 I.-No.: 11016 R. GehardDocuments registrar:

Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar

ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

DECLARATION OF CONFORMITY

ADDITIONAL INFORMATION

Danger!

Sound and vibration

Sound and vibration values were measured in accordance with EN 60745-1 and

EN 60745-2-13.

LpA sound pressure level ..................... 85,7 dB(A)

KpA uncertainty .............................................3 dB

LWA sound power level ....................... 95,4 dB(A)

KWA uncertainty ........................................2,47 dB

LWA sound power level guaranteed ......... 98 dB(A)

Wear ear-muffs.

The impact of noise can cause damage to hearing.

Total vibration values (vector sum of three directions) were determined in accordance

with EN 60745-1 and EN 60745-2-13.

Handle under load

Vibration emission value front handle

ah = 4,88 m/s2

Vibration emission value rear handle

ah = 4 m/s2

K uncertainty = 1.5 m/s2

The specied vibration value was established in accordance with a standardized testing

method. It may change according to how the electric equipment is used and may exceed

the speci ed value in exceptional circumstances.

The specied vibration value can be used to compare the equipment with other electric

power tools.

The specied vibration value can be used for initial assessment of a harmful effect.

Keep the noise emissions and vibrations to a minimum.

• Only use appliances which are in perfect working order.

• Service and clean the appliance regularly.

• Adapt your working style to suit the appliance.

• Do not overload the appliance.

• Have the appliance serviced whenever necessary.

• Switch the appliance off when it is not in use.

• Wear protective gloves.

For EU countries only

Never place any electric power tools in your household refuse.

To comply with European Directive 2012/19/EC concerning old electric and electronic

equipment and its implementation in national laws, old electric power tools have to be

separated from other waste and disposed of in an environment-friendly fashion, e.g. by

taking to a recycling depot.

Recycling alternative to the return request:

As an alternative to returning the equipment to the manufacturer, the owner of the

electrical equipment must make sure that the equipment is properly disposed of if p1-he no

longer wants to keep the equipment. The old equipment can be returned to a suitable

collection point that will dispose of the equipment in accordance with the national

recycling and waste disposal regulations. This does not apply to any accessories or aids

without electrical components supplied with the old equipment.

The reprinting or reproduction by any other means, in whole or in part, of documentation

and papers accompanying products is permitted only with the express consent of the iSC

GmbH.

Subject to technical changes

This consignment contains lithium-ion batteries.

In accordance with special provision 188 this consignment is not subject to the ADR

regulations. Handle with care. Danger of ignition in case of damage to the consignment

package. If the consignment package is damaged: Check and if necessary repackage.

For further information contact: 0049 1807 10 20 20 66 ( xed network 14 ct/min, mobile

phone max. 42 ct/min) Outside Germany charges will apply instead for a regular call to a

landline number in Germany.

LED lights do not illuminate on charger

Check the charging adaptor is securely plugged into the wall outlet.

Check the battery is rmly connected to the charging cradle.

Check that the charging jack is securely connected to the charging cradle.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. This is normal and

does not indicate a problem.

GENERAL SAFETY INSTRUCTIONS FOR ELECTRIC TOOLS

DANGER!

Read all safety regulations and instructions.

Any errors made in following the safety regulations and instructions may result in an electric shock,  re and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use.

The term “electric tool” used in the safety instructions refers to electric tools operated from the mains power supply (with a power cable) and to battery operated electric tools

(without a power cable).

1. Workplace safety

a) Keep your work area clean and well illuminated. Untidy or unlit work areas can

result in accidents.

b) Do not operate the electric tool in an environment where there is a risk of

explosions and where there are in ammable liquids, gases or dust. Electric tools

produce sparks which could set the dust or vapours alight.

c) Keep the electric tool out of the reach of children and other persons. If there is a

distraction, you may lose control of the appliance.

2. Electrical safety

a) The connector plug from this electric tool must  t into the socket. The plug should

never be altered in any way. Never use adapter plugs together with earthed electric

tools. Unaltered plugs and correct sockets reduce the risk of an electric shock.

b) Avoid bodily contact with earthed surfaces such as pipes, heating, ovens and

fridges. The risk of electric shock is increased if your body is earthed.

c) Keep the tool out of the rain and away from moisture. The ingress of water into an

electric tool increases the risk of an electric shock.

d) Do not use the cable to carry the electric tool, to hang it up or to pull it out of the

socket. Keep the cable away from heat, oil, sharp edges and moving parts of the

appliance. Damaged or entangled cables increase the risk of an electric shock.

e) If you are working outdoors with an electric tool, only use extension cables which

are designed speci cally for this purpose. Using specially designed outdoor

extension cables, the risk of electric shock is reduced.

f) If operation of the electric tool in a damp environment can not be avoided, use a

earth-leakage circuit-breaker. The earthleakage circuit-breaker reduces the risk of

an electric shock.

3. Safety of persons

a) Be careful, watch what you are doing and use an electric tool sensibly. Do not use

the tool if you are tired or under the in uence of drugs, alcohol or medication. A

moment of inattention when using the electric tool can result in serious injuries.

b) Wear personal protection equipment and always wear safety goggles. Wearing

personal protection (such as dust masks, non-slip safety shoes, safety helmet or

ear protection, depending upon the type and use of the electric tool) reduces the

risk of injury.

c) Make sure that the appliance cannot start up accidentally. Ensure that the electric

tool is switched off before you connect it to the power supply and/or insert the

battery, or pick up or carry the tool. If your  nger is on the switch whilst carrying

the electric tool or if you connect the appliance to the mains when it is switched

on, this can lead to accidents.

d) Remove keys and wrenches before switching on the electric tool. A tool or key

which comes into contact with rotating parts of the appliance can lead to injuries.

e) Avoid abnormal working postures. Make sure you stand squarely and keep

your balance at all times. In this way, you can control the electric tool better in

unexpected circumstances.

f) Wear suitable work clothes. Do not wear loose clothing or jewellery. Keep hair,

clothes and gloves away from moving parts. Loose clothing, jewellery or long hair

can get trapped in moving parts.

g) If vacuuming devices and draining devices can be  tted, make sure that these

are correctly attached and correctly used. The use of a dust extraction system

can reduce the danger posed by dust

4. Usage and treatment of electrical tool

a) Do not overload the appliance. Use the correct tool for your work. You will be

able to work better and more safely within the given performance boundaries.

b) Do not use an electric tool with a defective switch. An electric tool that cannot be

switched on or off is dangerous and must be repaired.

c) Pull the plug out of the socket and/or remove the battery before making any

adjustments to the appliance, changing accessories or put the appliance down.

This safety measure prevents starting the electric tool unintentionally.

d) Keep unused electric tools out of the reach of children. Do not allow people who

are not familiar with the appliance or who have not read these instructions to use

the appliance. Electric tools are dangerous if they are used by inexperienced

people.

e) Clean your electric tool carefully. Check whether moving parts are functioning

properly and not jamming, whether parts are broken or damaged enough that the

functioning of this electric tool is aff ected. Have damaged parts repaired before

using the appliance. Many accidents are caused by badly maintained electric

tools.

f) Keep your cutting tools sharp and clean. Carefully maintained cutting tools with

sharp cutting edges will jam less and are easier to control.

g) Make sure to use electric tools, accessories, attachments, etc. in accordance

with these instructions. Take the conditions in your work area and the job in hand

into account. Using electric tools for any purpose other than the one for which

they are intended can lead to dangerous situations.

5. Using and handling the cordless tool

a) Only charge the batteries in chargers that are recommended by the

manufacturer. A charger that is designed for a certain type of battery may pose a

 re risk if it is used with other types of battery.

b) Use only the correct batteries in the electric tools. The use of other batteries may

result in injuries and a  re risk.

c) Keep unused batteries away from paper clips, coins, keys, nails, screws and

other metallic objects that could cause a short circuit between the contacts. A

short circuit between the battery contacts may cause burns or a  re.

d) In case of incorrect use,  uid may escape from the battery. Avoid contact with

it. If you touch it by accident, rinse the aff ected area with water. If you get the

uid in your eyes, also seek medical advice. Leaking battery  uid can cause skin

irritation or burns.

6. Service

a) Have your electric tool repaired only by trained personnel using only genuine

spare parts. This will ensure that your electric tool remains safe to use.

We pay a great deal of attention to the design of every battery pack to ensure that we supply you with batteries which feature maximum power density, durability and safety.

The battery cells have a wide range of safety devices. Each individual cell is initially formatted and its electrical characteristic curves are recorded. These data are then used

exclusively to be able to assemble the best possible battery packs. Despite all the safety precautions, caution must always be exercised when handling batteries. The following

points must be obeyed at all times to ensure safe use.

Safe use can only be guaranteed if undamaged cells are used. Incorrect handling can cause cell damage.

Important: Analyses con rm that incorrect use and poor care are the main causes of the damage caused by high performance batteries.

CAUTION: THE CHARGER FOR THIS PRODUCT

SHOULD BE PROTECTED BY A RESIDUAL CURRENT

DEVICE (RATED AT 30mA OR LESS).

RUN

BRAKE ON BRAKE OFF

STOP

KNOW YOUR PRODUCT SETUP & PREPARATION

PXCCSS-018U

1. BATTERY & CHARGING (SOLD SEPARATELY) 3. OIL 4. SWITCHING ON/OFF 5. CUTTING

OPERATION

2. INSERTING & REMOVING THE BATTERY

1. Rear Handle

2. Trigger Switch

3. Oil Level Window

4. Chain Oil Tank Cap

5. Side Cover

6. Front Handle

7. Chain Brake

8. Guide Bar Locking Knob

9. Guide Bar

10. Chain

11. Bucking Spikes

12. Motor Cover

13. Lock-Off Button

14. Battery Seating

CORDLESS CHAINSAW

1 2 3 4 5 6 7

Running in the Chain

Prior to operation, a new chain should be run in for 2–3 minutes and then its

tension should be checked and adjusted as detailed in “MAINTENANCE”.

BATTERY & CHARGER (sold separately)

This tool is compatible with all battery and chargers from the Ozito

Power X Change Range.

The purchased battery will be shipped in a low charge condition, and requires charging

prior to use. Allow several cycles of charging and discharging (through use of the tool)

for the battery to reach its optimum performance / runtime.

1. Connect the charger into a mains power outlet.

4. The charger LED will illuminate

red signifying that the battery is

charging.

3. With the charger sitting on a at

surface, align the raised ribs on

the battery with the recess in the

charger and slide onto the charger

ensuring a rm connection.

2. The charger LED will ash green

showing power is being supplied

to the charger.

5. The charger LED will illuminate

green once the battery is charged.

Charging your lithium ion battery - Fast Charger

Charger LED Indicator

LED Indicator Situation

GREEN (Flashing) Stand By (no battery pack is inserted)

RED (Flashing) Battery is charging (low charge)

RED (Illuminated) Battery is charging (mid charge)

GREEN (Illuminated) Battery is 85% - 100% Charged and ready for use

BOTH(Illuminated) Battery pack is too hot or too cold (charging will begin

automatically when battery reaches correct charging

temperature).

BOTH (Flashing) Defective battery. Never charge a defective battery

pack!

Remove battery pack from charger.

Battery Charge Indicator

The purchased battery is equipped with a

battery charge indicator to show the state of

the battery charge.

Press the charge indicator button and look to

see which LED lights.

Battery requires

immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note: The battery needs to be removed from the tool to check the state of charge.

1. Connect the charger into a mains power outlet.

4. The charger LED will illuminate red signifying that the battery is charging.

3. With the battery sitting on a at

surface, align the raised ribs on the

battery with the recess in the charger

and slide onto the battery ensuring a

rm connection.

2. The charger LED will ash green

showing power is being supplied

to the charger.

5. When removing the charger from the

battery, rst press the battery release

tab, then slide the charger from its

position.

Charging your lithium ion battery - Eco Charger

Charger LED Indicator

LED Indicator Situation

GREEN (Flashing) Stand By (no battery pack is inserted)

RED (Illuminated) Battery is charging (low charge)

GREEN (Illuminated) Battery is charged and ready for use

RED (Flashing) Battery or Charger fault

RED & GREEN (Flashing) Battery pack is too hot or too cold (remove battery from

charger and store at room temperature 20ºC. Insert

battery again when at correct charging temperature). If

this happens again, the battery is defective and needs

to be replaced.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

Chain Brake

The chain brake operates automatically in the event of kick back.

The chainsaw is tted with a hand guard/chain brake which when operated brings

the chain to a stop within a tenth of a second.

The chain brake can be operated manually by pushing it forward or

automatically as a result of kickback.

Kickback occurs if the chain catches on the wood being cut and the chainsaw

recoils back suddenly.

In the event of kickback, your hand (which is on the front handle during

operation) jerks forward causing the back on your hand to push the guard

forward, engaging the chain brake and quickly stopping the chain.

2 1

APPLICATIONS

ACCESSORIES

15 Guide Bar Cover 16 Screwdriver

15 16

11 12 13 14

2. Start cutting by holding the

chainsaw by the front handle

and raising the rear handle.

1. Press the bucking spikes against

the timber ensuring the chain

is not making contact with the

material being cut.

3. If you cannot cut the timber

in a single stroke, apply

light pressure to the front

handle and continue sawing,

draw the chainsaw back a

little then apply the bucking

spikes a little lower and

nish the cut by raising the

rear handle.

4. Withdraw the chainsaw from

the cut while the chain is still

running.

Note: Chain bar oil may leak if the tool is left for long periods. This is

normal. If the tool is to be left unused for an extended time, drain the

oil from the tool. Rell before use. Pruning

Felling a Tree

Decide the direction in which you wish

the tree to fall, taking into account

the direction of the wind, the position

of branches, lean of the tree, ease of

subsequent limbing and bucking and

other factors prevalent at the time.

Pruning is the removal of a limb or branch from

a standing tree.

WARNING!: FELLING A TREE SHOULD ONLY BE

DONE BY TRAINED OPERATORS.

Limbing

WARNING!: FELLING ALWAYS KEEP A BALANCED

STANCE. DO NOT STAND ON THE LOG. BE ALERT TO

THE FACT THAT THE LOG MAY ROLL OVER. WHEN

WORKING ON A SLOPE, ALWAYS STAND ON THE UP HILL

SIDE OF THE LOG.

Limbing is the process of removing the

branches from a fallen tree. Check the

direction in which a branch will bend

before cutting it. Always cut on the

opposite side to the bending direction so

that the guide bar is not pinched in the cut.

For large limbs that cannot be removed in

one cut, make an initial cut from the bent side and nish by sawing from the

opposite direction. Do not remove limbs that are supporting the fallen tree on

the ground until the tree has been cut into lengths.

Bucking

Bucking is cutting a log into lengths for easier

handling. To saw a log lying on the ground,

rst saw halfway, then roll the log over and cut

from the opposite side. To saw the end of a log

supported off the ground, rst saw up from the

bottom one-third through the log then nish

by sawing down from the top. To saw a log in

the middle of two supports holding it off the

ground, rst saw down from the top one-third through the log then nish by

sawing up from the bottom.

CAUTION: FIRST AVOID CUTTING THE GROUND AS THIS

WILL VERY QUICKLY DULL THE SAW CHAIN.

WARNING!: DO NOT USE AN UNSTABLE FOOTHOLD

OR LADDER. DO NOT OVERREACH. DO NOT SAW

ABOVE SHOULDER HEIGHT. ALWAYS USE BOTH

HANDS TO HOLD THE SAW. FIRST CUT UP FROM THE

BOTTOM AND FINISH DOWN FROM THE TOP.

Hints and Tips

• Donotforcethesawintothecut.Applyonlylightpressurewhilstrunning

the chain.

• Ifthesawchaingetscaughtinthecut,donottrytoremoveitbytwisting

the guide bar or pulling forcibly. Use a lever or wedge to open up the cut

so that the saw chain is freed.

• Keepyourleftarmwithelbowlockedina“straightarm”positionto

withstand any kickback force.

• Whilecutting,always:

– Run the chainsaw motor at full speed. This makes the job safer, as there

is less chance of pull-in or kick-back.

– Position your body to the left of

the chainsaw so if it kicks back

uncontrollably, it goes over your right

shoulder, never stand in the cutting line

of the saw.

– Keep a rm grip with your left hand

on the front handle, with your thumb

securely below the handle.

STRAIGHT

ARM

POSITION

CHAIN

LINE

Switching ON

1. Pull the hand guard/chain brake towards

you.

2. Hold the front handle with your left

hand and the rear handle with your

right hand.

Switching OFF

1. Release the trigger switch, the chain

and motor will quickly stop.

3. Press the lock-off button with your

thumb, then squeeze the trigger

switch. The chainsaw starts after a

short delay.

4. The chain will now be running,

ready to make a cut. Release the

lock-off switch.

5. To check the lubricating system,

switch on the chainsaw and hold it

with the guide bar and chain above

some light coloured paper such as

newspaper. A steadily increasing

stain caused by oil spray shows

the lubricating system is working.

2. Fill the tank with chain bar oil.

The capacity of the chain oil

tank is 200ml. Do not over ll.

4. Always ll the oil tank when the

oil level is below the minimum

mark on the oil level window.

WARNING!: NEVER START WORK UNLESS THE

CHAIN AND BAR ARE LUBRICATED

1. Remove the chain bar oil cap.

3. Ret cap and clean any oil

spillage.

IMPORTANT: ONLY USE OIL THAT IS EXPRESSLY LABELLED

“CHAIN BAR OIL”.

CAUTION: FIRST TIME USERS SHOULD, AS A MINIMUM

PRACTISE, CUT LOGS ON A SAW-HORSE OR CRADLE

Installing a Battery into the chainsaw

1. Align the ribs of the battery with

the recess below the handle

Removing a Battery from the Chainsaw

2. Slide the battery in so

that it clicks into place.

1. Press and hold the battery

release tab to release the

battery.

2. Slide the battery out.

Especificaciones del producto

Marca:	Ozito
Categoría:	máquina de aserrar
Modelo:	PXCCSS-018U
Color del producto:	Bruin
Peso.:	- g
Longitud del cable:	7.5 m
Nivel de ruido:	72 dB
Consumo-anual-de-energía:	25.2 kWu
Amable:	Cilinderstofzuiger
Filtración de aire de aspiradora:	Miele Actieve AirClean
Rango:	12 m
Método de separación de la suciedad:	Filtrerend
tipo de limpieza:	Droog
Capacidad de polvo:	4.5 l
Potencia máxima de entrada:	800 W
Almacenamiento de cable:	Ja
Tipo de contenedor de aspiradora:	Stofzak
tipo de tubo:	Telescopisch
Material de tubería/manguera:	Roestvrijstaal
Manguera flexible:	Ja
Accesorio de almacenamiento/almacenamiento:	Ja
Asa de transporte:	Ja
enrollador de cable automático:	Ja
Indicador de depósito de polvo lleno:	Ja
control de potencia de succión:	Elektronisch
Uso correcto:	Thuis
Limpia superficies:	Carpet, Hard floor
Modo silencioso:	Ja
Cepillo de aspiradora incluido:	Parquet brush, Turbo brush
Boquilla de aspiración para cojines:	Ja
herramienta para rincones:	Ja
Filtro de protección del motor:	Ja
Mango con almacenamiento de accesorios.:	Ja