Ozito PXRHS-300U Manual de Usario

Ozito Hamer PXRHS-300U

Lee a continuación 📖 el manual en español para Ozito PXRHS-300U (2 páginas) en la categoría Hamer. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

SPECIFICATIONS

Input: 18V

Chuck Type: SDS-Plus

No Load Speed: 1,200/min

Impact Power: 1.2J

Impact Rate: 0-5,700bpm

Max. Torque: 10Nm

Weight: 1.45kg

CORDLESS ROTARY

HAMMER DRILL

ORIGINAL INSTRUCTIONS

ozito-diy.co.uk

PXRHS-300U

WHAT’S IN THE BOX

Cordless Rotary

Hammer Drill

MAINTENANCE TROUBLESHOOTING

DRILL DRIVER SAFETY WARNINGS

BATTERY AND CHARGER SAFETY WARNINGS

DESCRIPTION OF SYMBOLS

SPARE PARTS

Battery protection system

The tool is equipped with the battery protection system, which helps to ensure a long service

life.

The output power automatically cuts off during operation when the tool and/or battery are

placed under the following situations:

• When the tool is overloaded:

If this occurs, release the trigger switch and remove causes of overload, then pull the

switch trigger again to restart.

• When the remaining battery capacity becomes low:

Recharge the battery pack.

Note: The battery protection system does not in any way damage the tool.

Note: The indicated capacity may be lower than the actual level during use or immediately

after using the tool.

Battery & Charger

sold separately

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR

YOUR BATTERY CHARGER.

1. Before using the charger read all instructions and cautionary markings on the charger, battery pack

and the product using the battery pack.

2. This charger is not intended for any uses other than charging rechargeable batteries. Any other use

may result in risk of re, electric shock or electrocution.

3. Do not place any object on top of the charger or place the charger on a soft surface that may result

in excessive internal heat. Place the charger in a position away from any heat source.

4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when

disconnecting the charger.

5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise subjected

to damage or stress.

6. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord

could result in the risk of re, electric shock or electrocution.

7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in

any way. Have it checked by an electrician or power tool repairer.

8. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair is

required. Incorrect reassembly may result in a risk of electric shock, electrocution or re.

9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any cleaning.

Removing the battery pack will not reduce this risk.

10. Never attempt to connect 2 chargers together.

11. DO NOT store or use the tool and battery pack in locations where the temperature may reach or exceed

40ºC (such as inside sheds or metal buildings in summer).

12. The charger is designed to operate on standard household electrical power (240 volts). Do not

attempt to use it on any other voltage!

13. The battery pack is not fully charged out of the carton. First read the safety instructions and then

follow the charging notes and procedures.

14. The longest life and best performance can be obtained if the battery pack is charged when the air

temperature is between 18 - 24ºC. Do not charge the battery pack in an air temperature below 10ºC

or above 40ºC. This is important and will prevent damage to the battery pack.

15. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The battery

can explode in a re.

16. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks or

cracks, immediately discontinue use and do not recharge.

17. During charging, the battery must be placed in a well ventilated area.

WARRANTY

OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG 0417

All of our products undergo strict quality checks to ensure that they reach you in perfect

condition. In the unlikely event that your device develops a fault, please contact our service

department at the address shown on this guarantee card. You can also contact us by

telephone using the customer service number shown. Please note the following terms under

which guarantee claims can be made:

1. These warranty terms regulate additional warranty services, which the manufacturer

mentioned below promises to buyers of its new products in addition to their statutory

guarantee claims are not affected by this guarantee. Our guarantee is free of charge to you.

2. The warranty services only covers defects due to material or manufacturing faults on

a product which you have bought from the manufacturer mentioned below are limited to

either the rectication of said defects on the product or the replacement of the product,

whichever we prefer.

Please note that our devices are not designed for use in commercial, trade or professional

applications. A guarantee contract will not be created if the device has been used by

commercial, trade or industrial business or has been exposed to similar stresses during the

guarantee period.

3. The following are not covered by our guarantee:

- Damage to the device caused by a failure to follow the assembly instructions or due to

incorrect installation, a failure to follow the operating instructions (for example connecting

it to an incorrect mains voltage or current type) or a failure to follow the maintenance and

safety instructions or by exposing the device to abnormal environmental conditions or by

lack of care and maintenance.

- Damage to the device caused by abuse or incorrect use (for example overloading the

device or the use or unapproved tools or accessories), ingress of foreign bodies into the

device (such as sand, stones or dust, transport damage), the use of force or damage caused

by external forces (for example by dropping it).

- Damage to the device or parts of the device caused by normal or natural wear or tear or by

normal use of the device.

4. Your Product is guaranteed for a period of 60 months from the original date of purchase

and is intended for DIY (Do It Yourself) use only. Lithium Ion batteries and chargers are

covered by a 12 month warranty. Warranty excludes consumable parts. Guarantee claims

should be submitted before the end of the guarantee period within two weeks of the defect

being noticed. No guarantee claims will be accepted after the end of the guarantee period.

The original guarantee period remains applicable to the device even if repairs are carried

out or parts are replaced. In such cases, the work performed or parts tted will not result

in an extension of the guarantee period, and no new guarantee will become active for the

work performed or parts tted. This also applies if an on-site service is used.

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO

THE PLACE OF PURCHASE WITH YOUR REGISTER RECEIPT.

Please refer to the restrictions of this warranty concerning wearing parts, consumables and

missing parts as set out in the service information in these operating instructions.

CUSTOMER SERVICE HELPLINE

GB: 0151 294 4488

IRL: 1850 882711

Ozito-diy.co.uk

Warning Read instruction manual

ø Diameter

mA Milliamperes

Recycle battery Do not put in the rubbish

Polarity

Do not incinerate Do not get battery wet

Thermal cut-out protection

Double insulated

/min Revolutions or reciprocation per minute

Ah Amp hour

Indoor use only

Lithium Ion battery Do not use or store battery in

temperatures exceeding 50°C

Nm o Newton Meters nNo load speed

VVolts Hz Hertz

ac/~ W Alternating current Watts

Direct current

dc/

LED lights do not illuminate on charger

Check the charging adaptor is securely plugged into the wall outlet.

Check the battery is rmly connected to the charging cradle.

Check that the charging jack is securely connected to the charging cradle.

Variable speed trigger is locked

Ensure that the forward / reverse lever is in the correct position; pressed left for forwards

direction, pressed right for backwards direction. If it is in between the two settings the

variable speed trigger will be locked.

Rotary hammer drill has cut out during use

The battery charge could be completely depleted. Place the battery on the charging cradle

for 3-5 hours.

Sparking visible through the housing air vents

A small amount of sparking may be visible through the housing vents. This is normal and

does not indicate a problem.

WARNING! Wear ear protectors when drilling Exposure to noise can cause

hearing loss.

Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal

injury.

Hold power tool by insulated gripping surfaces, when performing an operation

where the cutting accessory may contact hidden wiring or its own cord. Cutting

accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give

the operator an electric shock.

Before drilling into walls, ceilings etc, ensure that there are no concealed power cables or pipes in the

cavity.

WARNING! Some dust created by power sanding, sawing, grinding,

drilling and other construction activities contain chemicals known to cause

cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

• Lead from lead-based paints

• Crystalline silica from bricks and cement and other masonry products

• Arsenic and chromium from chemically treated timber

Your risk from exposure to these chemicals varies, depending on how often you do this type of work. To

reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety

equipment, such as dust masks that are specially designed to lter out microscopic particles.

This appliance is not intended for use by young or inﬁrm persons unless

supervised by a responsible person to ensure that they can use the appliance safely. Young children

should be supervised to ensure that they do not play with the appliance.

1. When not in use, the drill should be stored in a dry, frost free location, keep

out of children’s reach.

2. Keep ventilation slots of the drill clean at all times and prevent anything from

entering.

3. If the housing of the drill requires cleaning, do not use solvents. Use of a cloth

only is recommended.

4. Blow out the ventilation slots with compressed air periodically .

Note: Ozito Industries will not be responsible for any damage or injuries

caused by repair of the drill by an unauthorised person or by mishandling.

WARNING! When using mains-powered tools, basic safety precautions, including the

following, should always be followed to reduce risk of ﬁre, electric shock, personal injury

and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency, before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

The charger has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating

plate.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for the UK.

This tools charger is double insulated; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for

added protection against injury resulting from a possible electrical insulation failure within the tool.

The power supply for this products charger should be protected by a residual current device (rated at 30mA

or less). A residual current device reduces the risk of electric shock.

GENERAL POWER TOOL SAFETY WARNINGS

ELECTRICAL SAFETY

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and

instructions may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference. The term “power tool” in the

warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power

tool.

1. Work area safety

a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.

b. Do not operate power tools in explosive atmospheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose

control.

2. Electrical safety

a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will reduce risk

of electric shock.

b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of

electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the

risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of electric shock.

f. If operating a power tool in a damp location is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the risk of electric shock.

3. Personal safety

a. Stay alert, watch what you are doing and use common sense when operating a power tool.

Do not use a power tool while you are tired or under the inﬂuence of drugs, alcohol or

medication. A moment of inattention while operating power tools may result in serious personal injury.

b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust

mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to

power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your

nger on the switch or energising power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the

power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure

these are connected and properly used. Use of dust collection can reduce dust-related hazards.

4. Power tool use and care

a. Do not force the power tool. Use the correct power tool for your application. The correct power

tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with

the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands

of untrained users.

e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts

and any other condition that may affect the power tool’s operation. If damaged, have the

power tool repaired before use. Many accidents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

g. Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the power tool for

operations different from those intended could result in a hazardous situation.

5. Battery tool use and care

a. Recharge only with the charger speciﬁed by the manufacturer. A charger that is suitable for one type of

battery pack may create a risk of re when used with another battery pack.

b. Use power tools only with speciﬁcally designated battery packs. Use of any other battery packs may

create a risk of injury and re.

c. When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection from one

terminal to another. Shorting the battery terminals together may cause burns or a re.

d. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation or burns.

6. Service

a. Have your power tool serviced by a qualiﬁed repair person using only identical replacement

parts. This will ensure that the safety of the power tool is maintained.

Spare parts can be ordered from the Special Orders Desk at your local

Bunnings Warehouse or Homebase store.

For further information, or any parts visit

www.ozito-diy.co.uk or contact Ozito Customer Service:

Great Britain: 0151 294 4488

Ireland: 1850 882711

E-mail: info@ozito-diy.co.uk

FWD

REV

KNOW YOUR PRODUCT SETUP & PREPARATION

1. BATTERY & CHARGING 3. SDS-PLUS ACCESSORY FITMENT 4. CONTROLS(sold separately) 5. DRILLING

OPERATION

FWD

REV

2. BATTERY INSTALLATION

1 SDS-Plus Accessory Holder

2 Accessory Locking Sleeve

3 Mode Selector

4 Front Handle

5 LED Worklight

6 Variable Speed trigger

7 Forward/Reverse Lever

8 Sure Grip Rear Handle

CORDLESS ROTARY HAMMER DRILL

The purchased battery will be shipped in a low charge condition, and requires charging

prior to use. Allow several cycles of charging and discharging (through use of the tool)

for the battery to reach its optimum performance / runtime.

1 Connect the charger into a mains power outlet.

4 The charger LED will illuminate

red signifying that the battery is

charging.

3 With the charger sitting on a at

surface, align the raised ribs on

the battery with the recess in the

charger and slide onto the charger

ensuring a rm connection.

2 The charger LED will ash green

showing power is being supplied

to the charger.

5 The charger LED will illuminate

green once the battery is charged.

Charging your lithium ion battery - Fast Charger

Charger LED Indicator

LED Indicator Situation

GREEN (Flashing) Stand By (no battery pack is inserted)

RED (Flashing) Battery is charging (low charge)

RED (Illuminated) Battery is charging (mid charge)

GREEN (Illuminated) Battery is 85% - 100% Charged and ready for use

BOTH(Illuminated) Battery pack is too hot or too cold (charging will begin

automatically when battery reaches correct charging

temperature).

BOTH (Flashing) Defective battery. Never charge a defective battery

pack!

Remove battery pack from charger.

Battery Charge Indicator

The purchased battery is equipped with a

battery charge indicator to show the state of

the battery charge.

Press the charge indicator button and look to

see which LED lights.

Battery requires

immediate charging

Low state of charge, requires charging soon.

Mid state of charge

Full state of charge.

Note: The battery needs to be removed from the tool to check the state of charge.

1 Connect the charger into a mains power outlet.

4 The charger LED will illuminate red signifying that the battery is charging.

3 With the battery sitting on a at

surface, align the raised ribs on the

battery with the recess in the charger

and slide onto the battery ensuring a

rm connection.

2 The charger LED will ash green

showing power is being supplied

to the charger.

5 When removing the charger from the

battery, rst press the battery release

tab, then slide the charger from its

position.

Charging your lithium ion battery - Eco Charger

Charger LED Indicator

LED Indicator Situation

GREEN (Flashing) Stand By (no battery pack is inserted)

RED (Illuminated) Battery is charging (low charge)

GREEN (Illuminated) Battery is charged and ready for use

RED (Flashing) Battery or Charger fault

RED & GREEN (Flashing) Battery pack is too hot or too cold (remove battery from

charger and store at room temperature 20ºC. Insert

battery again when at correct charging temperature). If

this happens again, the battery is defective and needs

to be replaced.

1 2 3 4 5 6 7 8

Accessory

SDS-Plus

1. Prior to inserting into chuck,

ensure the SDS-Plus accessory

is clear of dust and debris.

4. Rotate until accessory is inserted as

far as possible into locking sleeve.

5. Check SDS-Plus accessory is locked.

Try to pull it out. Note: It should have

approximately

10 – 20mm movement.

This is normal.

2. Prior to inserting into drill add

lubricant to the SDS-Plus accessory.

3. Insert SDS-Plus Accessory

into locking sleeve.

Note: The locking sleeve

should not be pulled back when

inserting accessory.

6. To remove the SDS-Plus accessory

pull back the locking sleeve and

pull accessory out.

1. Choose an

operation mode:

Hammer Drill

Rotate the mode selector to the hammer and

drill icon. This setting is recommended for use

when drilling holes in concrete and other masonry

products. The hammer action will be in operation

while simultaneously the drill bit rotates.

Drilling

Rotate the mode selector to the drill icon. This

setting is recommended for use when you desire the

accessory to rotate without hammer action. Ideal for

drilling into timber or steel when correct accessories

for such materials are used.

NOTE: PRIOR TO CHANGING MODES, THE VARIABLE

SPEED TRIGGER SHOULD BE RELEASED AND THE

DRILL SHOULD HAVE COME TO A COMPLETE STOP.

Mode selector

CAUTION: THE CHARGER FOR THIS PRODUCT

SHOULD BE PROTECTED BY A RESIDUAL CURRENT

DEVICE (RATED AT 30mA OR LESS).

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

BATTERY & CHARGER (sold separately)

This tool is compatible with all battery and chargers from the Ozito

Power X Change Range.

PXRHS-300U

Before starting to drill, perform a few simple checks.

3 Ensure workpiece is clamped and secured where possible.

1. Depress and release the variable

speed trigger to ensure it is not

locked on.

4. Hold the drill rmly and place the

bit at the point to be drilled.

2. Check the forward/reverse lever

is on desired setting.

5. Depress the variable speed

trigger to start the drill.

6. Move the drill bit into the workpiece.

Note: Do not force the drill or apply side pressure to elongate the hole. Let

the drill do all the work.

Forward/ Reverse Lever

Variable Speed Trigger

1. For forward rotation, push the fwd/rev lever towards the left side of the drill. For

reverse rotation push fwd/rev lever to the right.

1. To start drilling squeeze the variable

speed trigger.

2. To stop drilling release the trigger.

Note: The more the variable speed trigger is depressed, the faster the drill bit will

rotate.

Note: This product is not intended for driving

screws.

CAUTION: TO REDUCE THE RISK OF INJURY

WE RECOMMEND THE USE OF GLOVES WHEN

HANDLING DRILL BITS.

WARNING! Ensure the tool is turned off & battery removed before

performing any of the following operations.

Installing the Battery Pack

1 Slide the battery into the drill base until it clicks into place.

Removing the Battery Pack

1 Hold down the battery release button.

2 Slide the battery out.

Especificaciones del producto

Marca:	Ozito
Categoría:	Hamer
Modelo:	PXRHS-300U
Color del producto:	Zwart
Longitud del cable:	1.5 m
Tipo de fuente de energía:	USB
Número de teclas, teclado:	115
Certificación:	CE
Soporta Windows:	Windows 10, Windows 7, Windows 8, Windows 8.1
Tipo de retroiluminación:	RGB LED
Uso recomendado:	Gamen
Iluminar desde el fondo:	Ja
Conexión:	USB
Atajos:	Ja
Teclado numérico:	Ja
Soporta el sistema operativo Mac:	Ja
Incluye ratón:	Nee
Dispositivo señalador:	Nee
Teclas de Windows:	Ja
Compatible con Linux:	Ja
Color de superficie:	Monochromatisch
Material del conductor de contacto:	Goud
Diseño del teclado:	QWERTY
Soporte de la muñeca:	Nee
Interruptor de tecla del teclado:	Semi-mechanische sleutelschakelaar
Tamaño del teclado:	Volledige grootte (100%)
Teclado de estilo:	Recht
Dimensiones del teclado (AnxPrxAl):	470 x 185 x 36 mm
Peso del teclado:	920 g
Número-de-productos-incluidos:	1 stuk(s)
Lenguaje del teclado:	Portugees
Soporte para dispositivo móvil:	Ja
Teclas multimedia:	Ja
Anti-fantasma:	Ja
Retroiluminación personalizable:	Ja