Ozito SCMS-1621 Manual de Usario

Ozito máquina de aserrar SCMS-1621

Lee a continuación 📖 el manual en español para Ozito SCMS-1621 (8 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

ozito.com.au

DOUBLE BEVEL

SLIDE COMPOUND

MITRE SAW

210mm (8¼”)

INSTRUCTION MANUAL

SPECIFICATIONS

Motor: 1800W (S2 5min),

1500W (S1)

No Load Speed: 5,000/min

Blade: Ø210mm x Ø16 x 48T

Mitre Angle: 0-45 left & right°

Bevel Angle: 0-45 left & right°

Max. Cutting Capacity:

Mitre 0 x Bevel 90 : 62 x 310mm° °

Mitre 45 x Bevel 90 : 62 x 210mm° °

Mitre 0°x Bevel 45°: 36 x 310mm

Mitre 45°x Bevel 45°: Left 36 x 210mm

Right 20 x 210mm

SCMS-1621

WHAT’S IN THE BOX

Material Clamp

Compound Mitre Saw

Material Support Bar x 2

Hex Key, 5 & 6mm

Dust Bag

WARRANTY

0616

IN ORDER TO MAKE A CLAIM UNDER THIS

WARRANTY YOU MUST RETURN THE PRODUCT

TO YOUR NEAREST BUNNINGS WAREHOUSE WITH

YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY

PLEASE TELEPHONE OUR CUSTOMER SERVICE

HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

3 YEAR REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the

original date of purchase and is intended for DIY (Do It Yourself) use

only. If a product is defective it will be replaced in accordance with

the terms of this warranty. Warranty excludes consumable parts, for

example: blade, carbon brushes and dust bag.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other

than that specified on the tool.

• If the tool shows signs of damage or defects caused

by or resulting from abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction

manual.

• If the tool is disassembled or tampered with in any way.

• Professional, industrial or high frequency use.

TO ENSURE A SPEEDY RESPONSE PLEASE

HAVE THE MODEL NUMBER AND DATE OF

PURCHASE AVAILABLE. A CUSTOMER SERVICE

REPRESENTATIVE WILL TAKE YOUR CALL

AND ANSWER ANY QUESTIONS YOU MAY

HAVE RELATING TO THE WARRANTY POLICY

OR PROCEDURE.

OZITO Australia/New Zealand (Head Ofﬁce) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

The benefits provided under this warranty are in addition

to other rights and remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded

at law. You are entitled to a replacement or refund for a major

failure and for compensation for any other reasonably foreseeable

loss or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

Generally you will be responsible for all costs associated with

a claim under this warranty, however, where you have suffered

any additional direct loss as a result of a defective product you

may be able to claim such expenses by contacting our customer

service helpline above.

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to

the online manual.

1. Retractable Safety Guard

2. Material Support Bar

3. Material Clamp

4. Fence

5. Mitre Table

6. Mitre Table Lock

7. Bevel Angle Pointer

8. Lock Down Pin

9. Spindle Lock Button

10. Trigger

MITRE SAW

KNOW YOUR PRODUCT

1. ASSEMBLY

1. Remove foam packaging materials and using the carry handle,

carefully lift the mitre saw from its box and place it on a level

work surface.

1. Squeeze the clamp at the

end of the dust bag, place

over the dust extraction

port.

1. Insert each bar into the

two holes located on

both sides of the base.

2. Release cutting head from its transport position. While holding

the head of the saw down release the lock down pin.

11. Carry Handle

12. Slide Lock

13. Stabilising Bar

14. Bevel Lock

15. Bevel Release

16. Laser Guide

17. Additional Support Feet

18. Table Insert

19. Release Lever

SETUP & PREPARATION

Unpacking

Material Support Bars

Dust Bag

WARNING!: ENSURE THE TOOL IS SWITCHED

OFF AND DISCONNECTED FROM THE POWER

SUPPLY BEFORE PERFORMING ANY OF THE

FOLLOWING PROCEDURES.

HOLD

DOWN

TIGHTEN

2. Tighten screw when in

place.

Material clamp will assist

securing timber when making

cuts.

Note: The clamp can be

mounted on either the left or

right.

Material Clamp

2. SET-UP AND ADJUSTMENTS

1. Loosen mitre

table lock

2. Rotate the mitre table to the

desired mitre angle (left or

right) as shown by the mitre

angle pointer

Mitre Angle Adjustment

MITRE ANGLE

POINTER

3. Tighten mitre table lock at selected angle

Bevel Angle Adjustment

3. Tighten bevel lock at selected angle

Note: The mitre table features positive click stops at 0°, 15°, 22.5°,

31.6° and 45° for quick setting of common mitre angles.

Bench Mounting

The base of the saw has four

bench mounting holes (1 each

corner) that can be used to

mount it to a workbench or

mitre saw stand. Use four

screws or bolts (not included)

to secure.

WARNING!: ENSURE THE MITRE TABLE LOCK

IS TIGHT BEFORE MAKING A CUT. FAILURE

TO DO SO MAY RESULT IN THE MITRE TABLE

MOVING DURING OPERATION AND CAUSE

SERIOUS PERSONAL INJURY.

WARNING!: ENSURE THE BEVEL LOCK IS

TIGHT BEFORE MAKING A CUT. FAILURE TO

DO SO MAY RESULT IN THE CUTTING HEAD

MOVING DURING OPERATION AND CAUSE

SERIOUS PERSONAL INJURY.

Trenching refers to restricting the depth of cut and permits a “trench”

to be cut in the workpiece.

Bevel Angle Adjustment

Trenching

1. Ensure the cutting head is

raised, move the trenching

stop to the right as far as it

will go.

2. To adjust the trenching

depth rotate the trenching

depth adjustment screw.

3. To check that the blade

stops at the desired position,

lower the cutting head

until the trenching stop

adjustment screw touches

the trenching stop.

4. When the correct depth is

set. Lock it in position using

the trenching depth lock nut.

Slide Lock

When cutting a narrow piece of

wood it is not necessary to use

the slide mechanism. In these

circumstances, push back the

cutting head and ensure the slide

locking knob is tight to prevent the

cutting head from sliding.

To ensure the saw is standing securely when not mounting to a

workbench or mitre saw stand. Screw the Additional Support Feet to

the feet of the mitre saw with the fasterners provided. Then swing

out the Stabilising Bar to the rear until it engages.

18mm

30mm

1. Loosen bevel

lock.

2. BEVEL LEFT - Tilt the cutting head

to the desired

bevel angle

left as shown

by the bevel

angle pointer.

2a. BEVEL RIGHT - Tilt

the cutting head slighty

LEFT then pull the

bevel release.

BEVEL ANGLE

POINTER

2b. Tilt the cutting head to the desired

bevel angle right as shown by the

bevel angle

pointer.

BEVEL ANGLE

POINTER

Especificaciones del producto

Marca:	Ozito
Categoría:	máquina de aserrar
Modelo:	SCMS-1621
Color del producto:	Zwart, zilver
Función de alarma:	Ja
Sistema de suspensión para la pared.:	Ja
Tipo de Batería:	AA / AAA
Número de baterías (receptor):	2
Rango de medición de temperatura (exterior) (TT):	-29.9 - 59.9 °C
Número de baterías (sensor):	2
Rango de medición de temperatura (interior) (TT):	0 - 50 °C
radio reloj DCF:	Ja