Ozito SCMS-8STANDU Manual de Usario

Ozito máquina de aserrar SCMS-8STANDU

Lee a continuación 📖 el manual en español para Ozito SCMS-8STANDU (2 páginas) en la categoría máquina de aserrar. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
ASSEMBLY OF STAND
SLIDING
COMPOUND MITRE
SAW & STAND
210mm (8¼”)
ORIGINAL INSTRUCTIONS
STAND ASSEMBLY
STAND
FASTENERS
The stand is constructed by assembling each half of the structure and
then joining them together.
7 Bolt Small - 36 pc
8 Washer Small - 36 pc
9 Nut Small - 36 pc
10 Rubber Foot - 4 pc
11 Bolt Large with Rubber
Stopper - 4 pc
12 Saw Mounting Bolts - 4 pc
1 Short Upper Support - 2 pc
2 Short Lower Support - 2 pc
3 Long Upper Support - 2 pc
4 Long Lower Support - 2 pc
5 Upper Leg - 4 pc
6 Lower Leg - 4 pc
1197 10
16
2 3 4 5
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x2
x4 x4
1 Remove the stand components
from the box and group matching
pieces together. Check that you
have all the contents listed to the
left.
Note: All upper members can be
identied by the 2 holes very close
together.
2 Lay two upper and lower legs on
the ground aligning 2 of the bolt
holes, parallel to each other.
The upper leg sits outside the
lower leg.
3 Place one long lower support
in between the legs and align
the bolt holes. The side support
should have its lip on the high side
(facing up) and should sit inside
the legs.
Ensure the lip with the lengthened
bolt holes is facing upwards.
4 Once aligned, insert small bolts
into the 2 aligned holes at both
sides of the lower support. Insert
the bolt from the outside and
screw a small washer and nut
onto each bolt to secure (only
hand tight at this initial stage).
5 Place one long upper support on
the of the legs at the top outside
(This will ensure the mounting
holes will align correctly once
assembled)
Insert a bolt from the outside into
the 2 aligned holes at either side
of the upper support and hand
tighten a small washer and nut
onto each.
6 At this stage your frame should
look like this.
128
SCMS-8STANDU
Art.-No.: 30.003.16 I.-No.: 11017
WARNING! ONLY USE THIS STAND WITH THE PROVIDED
MITRE SAW. THE STAND MUST NOT BE USED WITH
OTHER PRODUCTS OR FOR OTHER APPLICATIONS.
SCMS-8STANDU
x2
x2
x2
12 Once all of the members are
joined together and all fasteners
are assembled, place the 4
mounting bolts into the holes
at the top of the stand. This
will ensure the mounting holes
align correctly while the stand is
tightened.
Tighten all nuts and bolts rmly.
Note: We recommend that the stand
is mounted to a stable surface
for additional stability.
13 The Rubber Feet can now be
tted and the large bolts with
rubber stops inserted into the
rubber feet.
These bolts can be adjusted to
level the stand.
14 Remove the mounting bolts that
you inserted prior to tightening
the stand, then place the saw on
the stand. The supplied mounting
bolts, washers and nuts should
be used to secure the saw to the
top of the stand.
7 Align one short lower support
inside the legs at the same height
as the long lower support. Ensure
that the lip of the side support is
facing up.
Insert 2 small bolts in the aligned
holes from the outside and
attaching a small washer and
nut (only hand tight at this initial
stage).
8 On the same side as Step 7,
assemble one short upper support
to the top of the upper leg using 2
small bolts, washers and nuts.
One half of the frame is now
complete.
9 Repeat the same process for the
other side, which should leave
you with 2 identical halves.
11 Align the holes of each opposing
member. Bolts, washers and nuts
can be inserted & tightened with
hand force only.
12 Insert a bolt into the 4 overlapping
lower support holes and attach a
washer and nut onto each.
10 These halves can now be aligned
together to complete the frame.
Note: Nuts & bolts should only be
nger tight at this stage.
0318

Especificaciones del producto

Marca: Ozito
Categoría: máquina de aserrar
Modelo: SCMS-8STANDU

¿Necesitas ayuda?

Si necesitas ayuda con Ozito SCMS-8STANDU haz una pregunta a continuación y otros usuarios te responderán


máquina de aserrar Ozito Manuales

Ozito

Ozito ECS-406A Manual de Usario

6 Octubre 2024
Ozito

Ozito OCS-018 Manual de Usario

20 Septiembre 2024
Ozito

Ozito PXCCSK-4182 Manual de Usario

18 Septiembre 2024
Ozito

Ozito PXBPCK-1825 Manual de Usario

18 Septiembre 2024
Ozito

Ozito PXTCSK-2520 Manual de Usario

18 Septiembre 2024
Ozito

Ozito PXPRSS-018 Manual de Usario

17 Septiembre 2024
Ozito

Ozito PXBPCS-1815 Manual de Usario

17 Septiembre 2024
Ozito

Ozito JSW-6100U Manual de Usario

3 Septiembre 2024
Ozito

Ozito PXCCSK-418 Manual de Usario

31 Agosto 2024
Ozito

Ozito RSW-5200 Manual de Usario

30 Agosto 2024

máquina de aserrar Manuales

Últimos máquina de aserrar Manuales

Hikoki

Hikoki C 6BU3 Manual de Usario

27 Octubre 2024
Dedra

Dedra DED7060 Manual de Usario

27 Octubre 2024
Einhell

Einhell KGS 190 Manual de Usario

27 Octubre 2024
Sun Joe

Sun Joe SWJ599E Manual de Usario

27 Octubre 2024
McCulloch

McCulloch CSE1935S Manual de Usario

27 Octubre 2024
Hikoki

Hikoki C10FSB Manual de Usario

27 Octubre 2024
Metabo

Metabo STA 18 LTX 150 BL Manual de Usario

26 Octubre 2024
Craftsman

Craftsman 917.377662 Manual de Usario

26 Octubre 2024
Maruyama

Maruyama MCV51 Manual de Usario

26 Octubre 2024
Powerplus

Powerplus POWX53300T Manual de Usario

22 Octubre 2024