Ozito WPS-2000U Manual de Usario

Ozito No categorizado WPS-2000U

Lee a continuación 📖 el manual en español para Ozito WPS-2000U (2 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
WALLPAPER
STRIPPER
2000W
ORIGINAL INSTRUCTIONS
SPECIFICATIONS
Voltage: 230-240V ~ 50Hz
Power: 2000W
Container Capacity: 4.5L
Steam Up Time: 15 minutes
Run Time: Approx. 80 minutes
Hose Length: 3m
IP Rating: IPX4
Weight: 1.83kg
WPS-2000U
WHAT’S IN THE BOX
Water Tank
ozito-diy.co.uk
WALLPAPER STRIPPER SAFETY WARNINGS
Steam Plate
OZITO UK Unit 9 Stadium Court, Wirral International Business Park, Plantation Road, Bromborough, Wirral, CH62 3QG
All of our products undergo strict quality checks to ensure that they reach
you in perfect condition. In the unlikely event that your device develops a
fault, please contact our service department at the address shown on this
guarantee card. You can also contact us by telephone using the customer
service number shown. Please note the following terms under which
guarantee claims can be made:
1. These warranty terms regulate additional warranty services, which the
manufacturer mentioned below promises to buyers of its new products
in addition to their statutory guarantee claims are not affected by this
guarantee. Our guarantee is free of charge to you.
2. The warranty services only covers defects due to material or
manufacturing faults on a product which you have bought from the
manufacturer mentioned below are limited to either the rectication of said
defects on the product or the replacement of the product, whichever we
prefer.
Please note that our devices are not designed for use in commercial, trade
or professional applications. A guarantee contract will not be created if the
device has been used by commercial, trade or industrial business or has
been exposed to similar stresses during the guarantee period.
3. The following are not covered by our guarantee:
- Damage to the device caused by a failure to follow the assembly
instructions or due to incorrect installation, a failure to follow the operating
instructions (for example connecting it to an incorrect mains voltage or
current type) or a failure to follow the maintenance and safety instructions
or by exposing the device to abnormal environmental conditions or by lack
of care and maintenance.
- Damage to the device caused by abuse or incorrect use (for example
overloading the device or the use or unapproved tools or accessories),
ingress of foreign bodies into the device (such as sand, stones or dust,
transport damage), the use of force or damage caused by external forces
(for example by dropping it).
- Damage to the device or parts of the device caused by normal or natural
wear or tear or by normal use of the device.
4. Your Product is guaranteed for a period of 36 months from the original
date of purchase and is intended for DIY (Do It Yourself) use only. Warranty
excludes consumable parts. Guarantee claims should be submitted
before the end of the guarantee period within two weeks of the defect
being noticed. No guarantee claims will be accepted after the end of the
guarantee period. The original guarantee period remains applicable to the
device even if repairs are carried out or parts are replaced. In such cases,
the work performed or parts tted will not result in an extension of the
guarantee period, and no new guarantee will become active for the work
performed or parts tted. This also applies if an on-site service is used.
IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST
RETURN THE PRODUCT TO THE PLACE OF PURCHASE WITH YOUR
REGISTER RECEIPT.
Please refer to the restrictions of this warranty concerning wearing parts,
consumables and missing parts as set out in the service information in
these operating instructions.
CUSTOMER SERVICE HELPLINE
GB: 0151 294 4488
IRL: 1850 882711
Ozito-diy.co.uk
WARRANTY
1117
WARNING! When using mains-powered tools, basic safety precautions, including the
following, should always be followed to reduce risk of re, electric shock, personal injury
and material damage.
Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,
before operating the tool.
Save these instructions and other documents supplied with this tool for future reference.
Before you connect the equipment to the mains supply make sure that the data on the rating plate are
identical to the mains data.
Using an Extension Lead
Always use an approved extension lead suitable for the power input of this tool. Before use, inspect the
extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or defective.
When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead not
suitable for the power input of the tool or which is damaged or defective may result in a risk of re and electric
shock.
GENERAL POWER TOOL SAFETY WARNINGS
ELECTRICAL SAFETY
WARNING! “Read all safety warnings, instructions, illustrations and specications
provided with this power tool.” Failure to follow the warnings and instructions may result in electric
shock, re and/or serious injury.
Save all warnings and instructions for future reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions can cause you to
lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching outlets will
reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase
the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the inuence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to
power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your
nger on the switch or energising power tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure
these are connected and properly used. Use of dust collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become complacent and
ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application. The correct power tool
will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or remove the battery pack, if detachable, from
the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools and accessories. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained power
tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5. Service
a. Have your power tool serviced by a qualied repair person using only identical replacement
parts. This will ensure that the safety of the power tool is maintained.
MAINTENANCE TROUBLESHOOTING
DESCRIPTION OF SYMBOLS
SPARE PARTS
Spare parts can be ordered from the Special Orders
Desk at your local Bunnings Warehouse or Homebase
store.
For further information, or any parts visit
www.ozito-diy.co.uk or contact Ozito Customer Service:
Great Britain: 0151 294 4488
Ireland: 1850 882711
E-mail: info@ozito-diy.co.uk
SERVICE INFORMATION
Danger! Read the operating instructions to reduce the risk of
inquiry.
Caution! Wear ear-muffs. The impact of noise can cause
damage to hearing.
Caution! Wear gloves.
Caution! Wear a breathing mask. Dust which is injurious to
health can be generated when working on wood and other
materials. Never use the device to work on any materials
containing asbestos!
Caution! Wear safety goggles. Sparks generated during
working or splinters, chips and dust emitted by the device can
cause loss of sight.
Warning! Steam.
Warning! Hot parts!
Double insulated / Protection class II
Please note that the following parts of this product are subject to normal
or natural wear and that the following parts are therefore also required
for use as consumables.
* Not necessarily included in the scope of delivery!
Category Example
Wear parts*
Consumables*
Missing parts DECLARATION OF CONFORMITY
For EU countries only
Never place any electric power tools in your household refuse.
To comply with European Directive 2012/19/EC concerning old electric
and electronic equipment and its implementation in national laws, old
electric power tools have to be separated from other waste and disposed
of in an environment-friendly fashion, e.g. by taking to a recycling depot.
Recycling alternative to the return request:
As an alternative to returning the equipment to the manufacturer, the
owner of the electrical equipment must make sure that the equipment is
properly disposed of if p1-he no longer wants to keep the equipment. The old
equipment can be returned to a suitable collection point that will dispose
of the equipment in accordance with the national recycling and waste
disposal regulations. This does not apply to any accessories or aids
without electrical components supplied with the old equipment.
The reprinting or reproduction by any other means, in whole or in part, of
documentation and papers accompanying products is permitted only with
the express consent of the iSC GmbH.
Subject to technical changes
Keep the noise emissions and vibrations to a minimum.
• Only use appliances which are in perfect working order.
• Service and clean the appliance regularly.
• Adapt your working style to suit the appliance.
• Do not overload the appliance.
• Have the appliance serviced whenever necessary.
• Switch the appliance off when it is not in use.
• Wear protective gloves.
Flexible Hose
WARNING!
• Always disconnect the mains plug before doing any work on the equipment.
• Keep steam away from plug sockets.
• The steam is produced at 100 degrees Celsius, wear protective clothing and
protect your hands with heat resistant gloves.
• Never detach the hose or remove the ller cap while the machine is in operation.
• Do not pull on hose too hard, move the machine around by using the handle.
• Do not stand on the machine and try to avoid stepping on the steam hose.
• Never cover or block the safety valve.
• Do not leave the machine unattended while still connected to power supply.
• Keep the tank on a at and level surface while in operation, failure to do so could
result in the machine overheating.
• Never direct steam hose or steam plate in the direction of anybody.
• Always keep steam plate tilted away from face, beware of hot droplets of water
especially when stripping ceilings and high areas.
• Wait for at least 5min after disconnection before removing cap.
• Use only tap water when lling machine, never overll.
• Never add any detergent or chemicals to water.
• Extreme care must be taken when the appliance is used in bathrooms/kitchens,
beware of electrocution from stored water in baths and sinks.
• The power must be disconnected before the machine is cleaned, make sure that
the power inlet is dry before reconnection.
Problem Cause Solution
The unit fails to
produce steam
No supply voltage Check the supply
voltage, the power
plug and the socket-
outlet.
Safety cut out The unit is not on
a level surface and
run low on water
causing the thermal
safety cut out to
engaged.
Allow the appliance
to cool down ll with
water and place on
level ground. The
machine will reset
after 15 minutes.
The tank leaks steam
from the pressure
valve
Blockage in hose. Allow the appliance
to cool down and
then check the hose
for blockages or
kinks.
Dong/Product-Management
Weichselgartner/General-Manager
explains the following conformity according to EU directives and norms for
the following product
Wallpaper Stripper WPS-2000U (Ozito)
2014/29/EU
2005/32/EC_2009/125/EC
X 2014/35/EU
2006/28/EC
X 2014/30/EU
2014/32/EU
2014/53/EC
2014/68/EU
90/396/EC_2009/142/EC
89/686/EC_96/58/EC
X 2011/65/EU
2006/42/EC
Annex IV
Notied Body:
Notied Body No.:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured L
WA
= dB (A); guaranteed L
WA = dB (A)
P = KW; L/Ø = cm
Notied Body:
2012/46/EU
Emission No.:
Standard references: EN 60335-1; EN 60335-2-54; EN 62233;
EN 55014-1; EN 55014-2; EN 61000-3-2; EN 61000-3-3
Landau/Isar, den 08.12.2017
First CE: 17 Archive-File/Record: NAPR017604
Art.-No.: 30.001.80 I.-No.: 11017 Documents registrar: Alex Kurz
Subject to change without notice Wiesenweg 22, D-94405 Landau/Isar
ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar
WARNING! ENSURE THE TOOL IS DISCONNECTED
AND ALLOWED TO COOL DOWN BEFORE
PERFORMING ANY MAINTENANCE.
After each use the container, hose and steam plate is cleaned thoroughly with
clean water. This will prevent any blockages occurring and provide reliable
performance when you next come to use it.
If the body of the wallpaper steamer requires cleaning, do not use solvents but a
moist soft cloth only.
When nished with the steamer allow the machine to cool before emptying the
tank, and always store the machine empty.
Descaling The Tank
Descaling the tank means cleaning the deposits that can build up from the use of
water with high mineral content. This process will maintain good performance of
the appliance, it may be necessary to descale the element in the tank.
Descaling products available at your local Bunnings Warehouse or Homebase
store can be used in your appliance. Always follow the manufactures instructions.
Note: Ozito Industries will not be responsible for any damage or injuries
caused by the repair of the sander by an unauthorised person or by mishandling
of the spray gun.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
KNOW YOUR PRODUCT SETUP & PREPARATION
2. ASSEMBLY AND SETUP1. BEFORE USE 3. OPERATION 4. STRIPPING WALLPAPER 5. OPERATION TIPS
1 Connect one end of
the exible hose to the
container steam outlet
tting.
1 Water Container
2 Filler Cap
3 Carry Handle
4 Steam Outlet Fitting
5 Steam Plate
6 Flexible Hose
WALLPAPER STRIPPER
2 Connect the other end of
the exible hose to the
steam plate.
OPERATION
Fitting the Flexible Hose
Filling Up the Water Container
Relling the Water Container
WARNING! THE POWER SUPPLY FOR THIS PRODUCT
SHOULD BE PROTECTED BY A RESIDUAL CURRENT
DEVICE (RATED AT 30MA OR LESS). A RESIDUAL CURRENT
DEVICE REDUCES THE RISK OF ELECTRIC SHOCK.
WPS-2000U
Helpful Tips
• Use this machine on level ground only.
• Heavy duty paper (paper that has been gloss painted and vinyl paper) might
require scoring to allow steam to penetrate into the paper.
• Operate steamer until water level is low then unplug the machine and
allow the tank to cool for at least 5 minutes before removing the ller cap -
BEWARE OF STEAM - and rell the tank.
• When nished with the steamer allow the machine to cool before emptying
the tank, and always store the machine empty.
1 Remove the ller cap. Fill
the water container with
clean water, no higher
than the MAX level. Then
screw the ller cap back on
tightly.
Note: It is recommended to
use hot water to reduce the
steam-up time.
1 While operating the unit,
continually check that the
water level does not drop
below the LOW mark.
2 If the tank needs relling,
disconnect from the power
supply and allow to cool
down for 5 minutes.
3 Remove the ller cap
(BEWARE OF STEAM) and
rell the container with
water up to the MAX mark
and then reattach the ller
cap tightly.
NOTE: Just before steam is produced a small amount of water will
bubble from the steam plate, this is normal.
Safety Cut Out
A safety cut out is tted to prevent the element from overheating if the water
level becomes too low. If the tank stops boiling during use this may be the
cause. Turn the machine off and wait for ve minutes before removing the ller
cap, then rell with clean water. The cut-out will reset itself in 15 minutes of
cooling and steam will be produced again.
Use this machine on level ground only. The cut-out will not protect the element
if the tank is tilted during use, which will damage the cut-out device permanently
and make it unable to reset and produce steam again.
Pressure Relief Valve
The unit is tted with a pressure relief valve for your protection. If the valve
operates steam will escape from the cover, disconnect power immediately and
allow to cool. Check hose for blockages. Allow the valve to reset (approx. 10
minutes) and resume work.
WARNING! DO NOT OVER FILL THE WATER CONTAINER OR
ALLOW THE LEVEL TO DROP BELOW THE MIN LEVEL. DO
NOT USE ANY ADDITIVES OR CHEMICALS. PLEASE ENSURE
THE FILLER CAP IS FULLY TIGHTENED BEFORE USING THE
WALLPAPER STRIPPER.
WARNING! DO NOT OVER FILL THE WATER CONTAINER OR
ALLOW THE LEVEL TO DROP BELOW THE MIN LEVEL. DO
NOT USE ANY ADDITIVES OR CHEMICALS. PLEASE ENSURE
THE FILLER CAP IS FULLY TIGHTENED BEFORE USING THE
WALLPAPER STRIPPER.
WARNING! ENSURE THE TOOL IS TURNED OFF AND
DISCONNECTED FROM THE POWER SUPPLY BEFORE
PERFORMING ANY OF THE FOLLOWING OPERATIONS.
WARNING! ENSURE ALL CONNECTIONS ARE SECURED
TIGHTLY BEFORE USE.
WARNING! PROTECTIVE GLOVES AND GLASSES
SHOULD BE WORN AT ALL TIMES TO AVOID INJURY.
WARNING! UNPLUG THE UNIT AND WAIT FOR AT
LEAST 5 MINUTES BEFORE REMOVING THE HOSE OR
CHANGING TOOLS.
Items Supplied
Please check that the article is complete as specied in the scope
of delivery. If parts are missing, please contact our service center or
the sales outlet where you made your purchase at the latest within
5 working days after purchasing the product and upon presentation
of a valid bill of purchase. Also, refer to the warranty table in the
service information at the end of the operating instructions.
• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or
transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the
guarantee period.
Danger!
The equipment and packaging material are not toys. Do not let
children play with plastic bags, foils or small parts. There is a
danger of swallowing or suffocating!
Proper Use
Suitable for steaming wallpaper for easy removal, including vinyl,
textured, multi layered and artex material.
The equipment is to be used only for its prescribed purpose. Any
other use is deemed to be a case of misuse. The user / operator
and not the manufacturer will be liable for any damage or injuries of
any kind caused as a result of this.
Please note that our equipment has not been designed for use in
commercial, trade or industrial applications. Our warranty will be
voided if the machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
Caution!
Residual risks
Even if you use this electric power tool in accordance with
instructions, certain residual risks cannot be rules out.
The following hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust mask is used.
2. Damage to hearing if no suitable ear protection is used.
3. Health damage caused by hand-arm vibrations if the equipment
is used over a prolonged period or is not properly guided and
maintained.
1 Connect the power cord to
the water container and plug
into a suitable power outlet.
1 Ensure the hose is
connected securely to both
the water container and
steam plate. Then switch the
unit on and allow the unit to
heat up.
2 Place the steam plate against the wallpaper starting from 1 edge.
Hold for roughly 10 seconds and them remove from the wall.
Note: Depending on the type of wallpaper, will determine the duration
that you will need to hold the steam plate against the wallpaper.
3 Move the steam plate to the spot immediately next to the one
previously steamed.
Note: If the wallpaper was installed in strips, it is recommended that
you follow the direction that it was applied to make removal easier.
4 The wallpaper from the rst position should now easily be peeled
away from the wall. The use of a scraping tool (not included) is
recommended.
If the wallpaper is difcult to remove you may need to extend the
time you hold the steam plate against the wallpaper.
5 Repeat this process by holding the steam plate against the
wallpaper and then continuing to peel off the paper until the strip of
wallpaper is removed.
2 Steam should be produced
after about 15 minutes,
depending on the amount
of water and water
temperature.
3 After use, unplug the cord
from the power supply or
from the container.
4 Allow the unit to cool before moving or emptying any left over
water.
15 min
15 min

Especificaciones del producto

Marca: Ozito
Categoría: No categorizado
Modelo: WPS-2000U

¿Necesitas ayuda?

Si necesitas ayuda con Ozito WPS-2000U haz una pregunta a continuación y otros usuarios te responderán


No categorizado Ozito Manuales

Ozito

Ozito PXBSPS-180 Manual de Usario

6 Octubre 2024
Ozito

Ozito SSH-240 Manual de Usario

6 Octubre 2024
Ozito

Ozito PXTLS-905 Manual de Usario

3 Octubre 2024
Ozito

Ozito ADWH-913V Manual de Usario

2 Octubre 2024
Ozito

Ozito PXBLEK-418 Manual de Usario

24 Septiembre 2024
Ozito

Ozito DMC-1000 Manual de Usario

21 Septiembre 2024
Ozito

Ozito PXMFTS-018 Manual de Usario

19 Septiembre 2024
Ozito

Ozito PXBCSS-184 Manual de Usario

15 Septiembre 2024
Ozito

Ozito PXPPS-1820 Manual de Usario

14 Septiembre 2024
Ozito

Ozito PXNGS-218 Manual de Usario

14 Septiembre 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024
Workzone

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024
Philips

Philips 43PUL7672 Manual de Usario

27 Octubre 2024
Manhattan

Manhattan 461504 Manual de Usario

27 Octubre 2024
Sungrow

Sungrow SG125HV Manual de Usario

27 Octubre 2024
Schneider

Schneider CCT724319 Manual de Usario

27 Octubre 2024
Technoline

Technoline WS 250 Manual de Usario

27 Octubre 2024
Livarno

Livarno IAN 354423 Manual de Usario

27 Octubre 2024
Kupper

Kupper 12152 Manual de Usario

27 Octubre 2024
JennAir

JennAir CARBON24L Manual de Usario

27 Octubre 2024