Panasonic KT2 Manual de Usario

Panasonic Termostato KT2

Lee a continuación 📖 el manual en español para Panasonic KT2 (32 páginas) en la categoría Termostato. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/32
TEMPERATURE CONTROLLER
KT2
INSTRUCTION MANUAL
2
P
Pr
re
ef
fa
ac
ce
e
Thank you for purchasing Temperature Controller KT2.
This manual contains instructions for the mounting, functions, operations and notes for operating the KT2.
For model conrmation and unit specications, please read this manual carefully before starting operation.
To prevent accidents arising from the misuse of this controller, please ensure the operator
receives this manual.
Characters used in this manual
Indication
Number, / -1 0 1 2 3 4 5 6 7 8 9
Indication
Alphabet A B C D E F G H I J K L M
Indication
Alphabet N O P Q R S T U V W X Y Z
Notes
• This instrument should be used in accordance with the specifications described in the manual.
If it is not used in accordance with the specications, it may malfunction or cause re.
• Be sure to follow the warnings, cautions and notices. If warnings are not observed, serious injury
or accidents may occur.
• The contents of this instruction manual are subject to change without notice.
• Care has been taken to assure that the contents of this instruction manual are correct, but if there
are any doubts, mistakes or questions, please inform our sales department.
• This instrument is designed to be installed in a control panel. If it is not, measures must be taken to
ensure that power terminals or other high voltage sections cannot be touched.
• Any unauthorized transfer or copying of this document, in part or in whole, is prohibited.
•Panasonic Electric Works Co., Ltd. is not liable for any damage or secondary damage(s) incurred
as a result of using this product, including any indirect damage.
Safety precautions
(Be sure to read these precautions before using our products.)
The safety precautions are classied into two categories: “Warning” and “Caution”.
Depending on circumstances, procedures indicated by Caution may have serious consequences,
so be sure to follow the directions for correct usage.
Warning
Procedures which may lead to dangerous conditions and cause death or serious injury,
if not carried out properly.
Procedures which may lead to dangerous conditions and cause supercial to medium injury
or physical damage or may degrade or damage the product, if not carried out properly.
Caution
3
1
1.
.I
In
ns
st
ta
al
ll
la
at
ti
io
on
np
pr
re
ec
ca
au
ut
ti
io
on
ns
s
Caution
This instrument is intended to be used under the following environmental conditions
(IEC61010-1): Overvoltage category , Pollution degree 2
Ensure the mounting location corresponds to the following conditions:
• A minimum of dust, and an absence of corrosive gases
• No ammable or explosive gases
• No mechanical vibrations or shocks
• No exposure to direct sunlight, an ambient temperature of 0 to 50 (32 to 122 )
that does not change rapidly
• An ambient non-condensing humidity of 35 to 85%RH
• No large capacity electromagnetic switches or cables through which large current
is owing
• No water, oil or chemicals or where the vapors of these substances can come into
contact with the unit
Note: Do not install this instrument near ammable material even though the case of this instrument
is made of ame-resistant resin.
Avoid setting this instrument directly on ammable material.
2
2.
.W
Wi
ir
ri
in
ng
gp
pr
re
ec
ca
au
ut
ti
io
on
ns
s
Caution
• Use the solderless terminal with an insulation sleeve in which an M3 screw ts, when wiring the
KT2.
• Tighten the terminal screw with the specied torque. If excessive force is applied to the screw
when tightening, the terminal screw or case may be damaged.
• Do not apply a commercial power source to the sensor which is connected to the input terminal
nor allow the power source to come into contact with the sensor.
• This controller does not have built-in power switch, circuit breaker or fuse.
It is necessary to install them near the controller.
(Recommended fuse: Time-lag fuse, rated voltage 250V AC, rated current 2A)
3
3.
.R
Ru
un
nn
ni
in
ng
ga
an
nd
dm
ma
ai
in
nt
te
en
na
an
nc
ce
ep
pr
re
ec
ca
au
ut
ti
io
on
ns
s
Warning
• It is recommended that the PID auto-tuning be performed on the trial run.
• Do not touch live terminals. This may cause electric shock or problems in operation.
• Turn the power supply to the instrument OFF before retightening the terminal and cleaning.
Working or touching the terminal with the power switched ON may result in severe injury or
death due to Electric Shock.
• Use a soft, dry cloth when cleaning the instrument.
(Alcohol based substances may tarnish or deface the unit)
• As the display section is vulnerable, do not strike or scratch it with a hard object.

Especificaciones del producto

Marca: Panasonic
Categoría: Termostato
Modelo: KT2

¿Necesitas ayuda?

Si necesitas ayuda con Panasonic KT2 haz una pregunta a continuación y otros usuarios te responderán


Termostato Panasonic Manuales

Panasonic

Panasonic KT2 Manual de Usario

14 Agosto 2024

Termostato Manuales

Últimos Termostato Manuales

Danfoss

Danfoss ORT-10 Manual de Usario

27 Octubre 2024
Hunter

Hunter 44279 Manual de Usario

27 Octubre 2024
Heatmiser

Heatmiser PRT-ETS Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser PRT-W Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser PRTHW Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser PRT-EWTS Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser DT-N Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser DT-EW Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser PRTHW-WTS Manual de Usario

26 Octubre 2024
Heatmiser

Heatmiser PRT-RPTS Manual de Usario

26 Octubre 2024