Panasonic PT-VW430U Manual de Usario
Lee a continuación 📖 el manual en español para Panasonic PT-VW430U (4 páginas) en la categoría proyector. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
CARE LABEL
Always check the care labels, especially when placing garments
in the tumble dryer for the rst time. Below are the most
commonly used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please
register your product on www.hotpoint.eu/register
EN
Quick guide
Before using the appliance carefully read the Safety
Instructions.
FIRST TIME USE
Remove all the tapes used to hold items on the machine.
Before you use it, clean the inside of the drum to remove any
dust that could have accumulated during transport. Slight odour
or vapour may be found if you open the door during its rst use,
this is normal and should only last a few minutes.
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is properly
connected, either to the dryers's water tank or to your domestic
drainage system.
The dryer must be installed in a room with a temperature
ranging between 5°C and 35°C to ensure proper operation.
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your condenser unit regularly
(monthly).
- remember to clean your lter after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door lter. Do not load items that
are dripping wet. Do not tumble dry large, very bulky items.
3. Close the door.
4. Press the "On/O" button.
5. Select the most suitable programme
for the type of fabric in that
load.
6. Select the options, if necessary.
7. Press the "
Start/Pause"
button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
9. Turn the machine o by pressing the "On/O" button, open the
door and pull the clothing out. If the machine is not switched o
manually, after about a quarter of an hour from the end of the
cycle , the appliance turns o automatically to save energy.
Note that some programme/option accords with "Crease Care"
system. This means that for some hours, after the end of the
drying cycle, the drum rotates at regular intervals to prevent the
formation of creases.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
TRANSPORT AND HANDLING
Never lift the dryer by holding on to its top side.
1. Unplug the dryer
2. Remove the water from the water tank completely.
3. Make sure that door and water tank are properly closed.
4. If the drain hose is connected to your drainage system, re-connect
it to the back of the dryer (see "Installation" section in the Safety
Instructions).
OPENING THE DOOR DURING THE CYCLE
Laundry can be checked while the drying cycle runs and any
garments already dry can be removed, while drying continues for
the remaining items. After closing the door, press the "Start/Pause"
button to resume machine operation.
CONTROL PANEL
1 ON/OFF Button (hold to Reset)
2 Programme Selection Knob
3 Start/Pause
Options Buttons
4 Crease Care
5 Dryness Level
6 Start Delay
7 Timed Drying
8 Cycle End Signal
9 Gentle (hold for Key Lock)
10 Rapid hold to Mute)(
INDICATORS
Dryness Level: Iron Dry - Hanger Dry - Cupboard Dry - Extra Dry
Programme Status: ENDDrying - Cool Down - End of Cycle
Empty water tank Clean door lter - - Clean the condenser unit
Refer to the troubleshooting section: Failure: Call after sales service.
END
EN
EN
EN
END
D
D
D
1
3
2
4
10
8
9
5 6 7
h
h
h
h
h
h
OPTIONS
These buttons allow you to personalise the selected programme
according to personal requirements.
Not all options are available for all programmes. Some options
may be incompatible with ones you have previously set; if so,
you will be alerted by the buzzer and/or blinking indicators.
If the option is available, the option indicator will stay on. The
programme may retain some options selected in previous drying
cycles.
Dryness Level
Press the related button several times to obtain a dierent
level of residual moisture on garments. An indicator signals the
level being selected.
Iron Dry: very delicate drying. Garments will be more
easily ironed immediately after the cycle.
Hanger Dry: a level intended for delicate garments ready
to be hanged.
Cupboard Dry: the garments are ready to be folded and
put away.
Extra Dry: used for garments to be worn at the end of the
cycle.
h
Start Delay
This option allows you to delay the start of the cycle. Press the
corresponding button several times to obtain the required delay.
After having reached the max settable time, the option is reset
by pressing the button again. An indicator on the control panel
signals the time being selected. After having pressed the "Start/
Pause" button,the machine signals the time remaining to the
start of the cycle. In case of door opening, press the "Start/Pause"
button once the door has been closed.
Timed drying
This option allows to set the drying time. Press the
corresponding button to set the required time for drying. An
indicator on the control panel signals the time being selected.
Cycle End Signal
This option activates a prolonged buzzer at the end of the
cycle. Enable it if you do not think you will hear the normal sound
at the end of the cycle. This option remains in memory if selected
in the previous drying.
Gentle
Enables a more gentle treatment of the laundry by reducing the
drying temperature.
Key Lock
This option makes all machine controls inaccesible, except the
"On/O" button. When the machine is on:
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the
indicator goes o.
This option remains in memory if selected in the previous drying.
Crease Care
This option adds a crease treatment at the end of the cycle by
means of a periodic rotation of the drum (duration up to 10
hours). It is particularly suitable when it is not possible to remove
the laundry as soon as the drying ends. If this option is used
together with the "Start Delay", the crease treatment is also added
to the "Start Delay" phase. This option remains in memory if
selected in the previous drying.
Mute
This option turns o all sounds of the control panel. Only
warnings remain active. When the machine is on:
• to activate the option, keep the button pressed until the
indicator goes on.
• to disable the option, keep the button pressed until the indicator
goes o.
Rapid
Enables quicker drying.
PROGRAMS
The duration of these programs will depend on the size of the
load, types of textiles, the spin speed used in your washer and
any extra options selected. In machines equipped with display,
the duration of the cycles is shown on the control panel. The
remaining time is constantly checked and adjusted during the
drying cycle to show the best possible estimate.
Option to use - If all your loads on Automatic Cycles are
consistently less dry or more dry than you would like, you may
increase or decrease the dryness level using the specic option.
Eco Cotton Max* kg
This is the most ecient programme in terms of energy
consuption and is suitable for drying normal wet cotton laundry.
The values on the Energy Label are based on this programme.
NOTE: For optimal energy eciency, select “Cupboard Dry” using
dryness level option. To increase the dryness level, select “Extra
Dry”.
Hygiene 4 kg
This is a cycle using high heat, which has been proven to
reduce household bacteria. This cycle is not recommended for all
fabrics, use it only for heavyweight fabrics.
Jeans 3 kg
For drying sturdy cotton jeans-wear and garments, like
denim, such as trousers and jackets.
Refresh
A short programme suitable for refreshing bres and
garments through the emission of fresh air. Do not use with
garments that are still wet. It can be used on with any load size
but is more eective with small loads. 20 minutes.It lasts about
Duvet
Programme intended to dry bulky garments, such as a single
duvet.
Bed & Bath Max* kg
This programme is intended for drying cotton towels and bed
sheets.
Baby 2 kg
A programme intended to dry babies' garments and linen
(cotton and chenille), as well as delicate garments. Do not dry
garments with plastic elements.
Pre-Iron
This cycle allows to stretch the bres of garments thus
making ironing and folding easier. Do not use with garments that
are still wet. Suitable for small loads of cotton textiles or cotton
blends.
Daily 2 kg
Ideal for drying cotton blend or synthetic blend garments at
high speed in the washing machine.
Shirts 3 kg
Programme ideal for cotton or cotton/synthetic blend
shirts.
Silk 0.5 kg '
Gentle drying ideal for silk garments.
Wool 1 kg
Programme for drying wool clothes. It is advisable to turn
the garments inside out before drying. If heavy edges
remain damp, leave them to dry naturally.
Mixed 4 kg
This programme is ideal for drying cotton and synthetic
fabrics together.
Rapid 30' 0.5 kg
Ideal for drying cotton garments spun at high speed in the
washing machine.
Synthetics 4 kg
For drying synthetic garments.
EN
Quick guide
*MAX LOAD 8 kg (Dry load)
Power consumption
o-mode (Po) - Watts 0.15
left-on mode (Pl) - Watts 0.15
Programmes Minuteskg kWh
Eco Cotton * 8 4.75 156
Eco Cotton 4 2.55 87
Synthetics 4 2.26 110
*This is the most ecient programmes in terms of energy consuption
and is suitable for drying normal wet cotton laundry. The values on
the Energy Label are based on this programme.
*MAX LOAD 9 kg (Dry load)
Power consumption
o-mode (Po) - Watts 0.15
left-on mode (Pl) - Watts 0.15
Programmes Minuteskg kWh
Eco Cotton * 9 5.23 162
Eco Cotton 4.5 2.79 92
Synthetics 4 2.26 110
*This is the most ecient programmes in terms of energy consuption
and is suitable for drying normal wet cotton laundry. The values on
the Energy Label are based on this programme. The values reported in
the table are obtained with the condensed water drained externally
through the drain hose.
CARE AND MAINTENANCE
WARNING: unplug the dryer during the cleaning and
maintenance procedures.
Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and empty it into a sink or
other suitable drain, then place it back properly. Do not use the
dryer without having inserted the container back in place.
Cleaning the door lter after each cycle (see Fig. B).
Pull the lter out and clean it by removing the lint from the lter
surface under running water or using a vacuum cleaner. For optimal
performance, dry up the lter before inserting it back in place.
Do not use the dryer without having reinserted the lter in place.
Remove the door lter as described below:
1. Open the door and pull the lter upwards.
2. Open the lter and remove the lint from all its parts. Replace
the lter correctly making sure it is fully seated.
The lter is an essential part for drying. It is intended to
collect the lint formed during the drying process. If the
lter is clogged, the air ow inside the dryer can become
seriously aected: this will increase the drying time and
energy consumption, and could damage the dryer. If this
procedure is not carried out properly, the dryer may not
start.
Cleaning the condenser unit (see Fig. C).
Remove the condenser unit regularly (monthly) and clean o
any u deposits from the plates by running cold water along
its rear end. The light on after several cycles is just a reminder to
carry on this activity periodically.
Removing the condenser:
1. Open the condenser cover, unlock the three catches by
turning them 90° anticlockwise.
2. Pull on the grip to remove the condenser.
3. Clean the surface of the seals.
4. Replace the unit with the arrows pointing upwards, while
making sure that the catches are securely xed.
PRODUCT DESCRIPTION
1. Water tank
2. Air intake
3. Door lter
4. Condenser unit
5. Condenser cover
A B
C
1
3
2
4
5
Cleaning the tumble dryer
• The external metal, plastic and rubber parts can be cleaned
with a damp cloth.
• Clean the front air intake grille regularly (every 6 months)
with a vacuum cleaner to remove any lint, u or dust
deposits. Furthermore, remove any lint deposits from the
front part of the condenser and from the lter area, using a
vacuum cleaner every so often.
• Do not use solvents or abrasives.
Especificaciones del producto
| Marca: | Panasonic |
| Categoría: | proyector |
| Modelo: | PT-VW430U |
¿Necesitas ayuda?
Si necesitas ayuda con Panasonic PT-VW430U haz una pregunta a continuación y otros usuarios te responderán
proyector Panasonic Manuales
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
24 Octubre 2024
2 Octubre 2024
proyector Manuales
- proyector Sony
- proyector Samsung
- proyector Casio
- proyector LG
- proyector HP
- proyector Philips
- proyector Epson
- proyector JVC
- proyector Toshiba
- proyector Canon
- proyector Acer
- proyector Aiptek
- proyector Reflecta
- proyector BenQ
- proyector Sharp
- proyector Klarstein
- proyector Hitachi
- proyector Pyle
- proyector Livoo
- proyector Asus
- proyector Hisense
- proyector Renkforce
- proyector Kodak
- proyector RCA
- proyector 3M
- proyector Overmax
- proyector GPX
- proyector Blaupunkt
- proyector Lenovo
- proyector Yaber
- proyector Salora
- proyector Optoma
- proyector Sanyo
- proyector Mitsubishi
- proyector Nec
- proyector Oki
- proyector Steinel
- proyector Eiki
- proyector Marantz
- proyector Adj
- proyector Barco
- proyector Dahua Technology
- proyector Derksen
- proyector Ricoh
- proyector Dell
- proyector InFocus
- proyector Bauer
- proyector Naxa
- proyector Nebula
- proyector Viewsonic
- proyector D-Link
- proyector Vivitek
- proyector Eurolite
- proyector Smart
- proyector Odys
- proyector Laserworld
- proyector Maxell
- proyector Elmo
- proyector Kogan
- proyector Celexon
- proyector Prixton
- proyector Fun Generation
- proyector Christie
- proyector PLUS
- proyector Ultimea
- proyector Boxlight
- proyector AAXA Technologies
- proyector Miroir
- proyector Vankyo
- proyector AWOL Vision
- proyector Smart Tech
- proyector Atlantis Land
- proyector KickAss
- proyector Microtek
- proyector Beghelli
- proyector VAVA
- proyector Panamorph
Últimos proyector Manuales
26 Octubre 2024
24 Octubre 2024
24 Octubre 2024
22 Octubre 2024
22 Octubre 2024
22 Octubre 2024
21 Octubre 2024
21 Octubre 2024
21 Octubre 2024
21 Octubre 2024