Peavey ISM 5Tx Manual de Usario

Peavey Vocero ISM 5Tx

Lee a continuación 📖 el manual en español para Peavey ISM 5Tx (2 páginas) en la categoría Vocero. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/2
Architectural Acoustics® ISMTM 5Tx Loudspeaker
4
Enclosure Materials & Finish: Black molded ABS cabinet with matte finish.
Cabinet has UL 94 HB flame retardant plastic for safety, with matching perforated
powder-coated steel speaker grille. Also available in white.
Mounting provisions: One set of two inserts, one on the top center and one on the
bottom center for the supplied speaker bracket. One wall-mount key-hole on the rear
near the top.
Dimensions (H x W x D): Cabinet Only: 8.87 in. x 5.88 in. x 5.57 in.
225 mm x 149 mm x 141 mm
With Mounting Bracket (Approx): 10.0 in. x 5.88 in. x 8.0 in.
254 mm x 149 mm x 203 mm
Net Weight: 5.5 Lbs. (2.5 kg)
Architectural & Engineering Specifications
The loudspeaker system shall have an operating range of 65 Hz to 20 kHz. The
nominal output level shall be 88 dB when measured at a distance of one meter with
an input of one watt when in 8 Ohm Thru mode. The nominal impedance shall be
8 ohms, and the maximum continuous power handling shall be 40 watts, maximum
program power of 80 watts and a peak power input of at least 160 watts, with a
minimum amplifier headroom of 3 dB, in 8 ohm thru mode. A 70.7 V line
transformer with switched taps at 16W, 8W, 4W and 2W shall be incorporated, with
provisions for 8 ohm Thru mode as well. A 5” nominal diameter water-resistant
woofer with rubber surround shall be used in conjunction with a 1” nominal
diameter polymer dome tweeter, and a frequency dividing network shall divide the
frequencies between them at 7.4 kHz.
The nominal radiation geometry shall be 110 degrees in the horizontal plane and
110 degrees in the vertical plane. The outside dimensions shall be 8.87 inches
high by 5.88 inches wide by 5.57 inches deep. The molded plastic cabinet shall be
made from flame-retardant ABS, meeting UL 94 HB requirements. The weight
shall be 5.5 pounds. The loudspeaker system shall be a Peavey model ISM™5Tx.
2 YEAR LIMITED WARRANTY
NOTE: For details, refer to the warranty statement. Copies of this statement may
be obtained by contacting Peavey Electronics Corporation, P.O. Box 2898,
Meridian, Mississippi 39301-2898.
Copyright 2011 Peavey Electronics Corporation All Rights Reserved
®
Architectural Acoustics® ISMTM 5Tx Loudspeaker
2
Product Description
The ISM™5Tx is a small format 2-way speaker system that is perfect for any application
from foreground music to speech reinforcement. The ISM™5Tx has a hi-fi sound
character with good clarity, which is ideal for music systems in bars, taverns, arenas,
lounges, arcades or anywhere multi-channel, multi-speaker sound systems are required.
This speaker utilizes a specially designed 5” woofer and a 1” poly dome tweeter. The
lightweight and rugged injection-molded cabinet is weather-resistant for indoor or
outdoor use. A curved black metal perforated grille provides driver protection and a
professional appearance.
The compact, lightweight package coupled with its smooth response makes this system
ideal for the smaller venues where space is at a premium.
The ISM™5Tx speaker system is rated at 80W program power handling. Spring-loaded
terminal input connectors make hook-up extremely simple. Incorporation of a 70.7 volt
line transformer with taps at 16W, 8W, 4W and 2W allow easy use with 70.7 volt
distributed systems. The tap selector switch also has an 8 ohm input option, so the
ISM™5Tx speaker system can be used with a direct connection to a power amp,
providing unequaled versatility.
Product Features
• Premium 5" woofer with rubber surround
• 1" polydome dynamic tweeter
• Weather-resistant
• 80 Watts program power handling
• Built-in switched 70 Volt Line transformer w/Taps at 16W, 8W, 4W, 2W
• 8 Ohms nominal position on switch
• Small lightweight molded enclosure
• Flame retardant enclosure, to UL 94 HB
• Molded-in mounting inserts
• Mounting bracket included
Mounting and Installation
CAUTION!
Before attempting to suspend or mount this speaker, consult a certified structural
engineer. Speaker can fall from improper suspension, resulting in serious injury and
property damage. The ISM™5Tx can be mounted using the supplied mounting bracket.
Use only the correct mating hardware and appropriate bracket mounting hardware. All
associated rigging is the responsibility of others.
Architectural Acoustics® ISMTM 5Tx Loudspeaker
3
CAUTION!
When using the 70.7V distribution system transformer inputs, it is typically required that
an infrasonic filter be used to prevent saturation of the transformer, and possible
overloading of the power amplifier. A minimum of an 18 dB/octave high-pass filter set to
a –3 dB point of 80 Hz or higher should be used to filter the low frequencies. It is
recommended that the filter be a 24 dB/octave Linkwitz-Riley type set to 65 Hz (-6 dB
point) for maximum reliability and performance.
Specifications
Frequency Range: 65Hz – 20kHz (-10 db, 1 meter on-axis, swept-sine in ½
space environment)
Frequency Response: 92Hz – 18kHz (+/- 4db, 1 meter on-axis, swept-sine in ½
space environment)
Power Handling: 8 Ohm Thru Mode: 40 W continuous, , 80 W program 160 W
peak. Transformer taps for 70.7 volt operation: 16W, 8W, 4W and 2W
Sound Pressure Level, 1 Watt, 1 meter in anechoic environment: 88 dB SPL,
(2.83V input, 8 ohm thru mode) Transformer Losses, Less than 1 dB when in .
70.7V input mode.
Maximum Sound Pressure Level (1 meter, 8 ohm thru mode): 103 dB SPL
continuous, 109 dB SPL peak
Nominal Radiation Angle: 110 degrees horizontal by 110 degrees vertical
Transducer Complement: Low Frequency Section: 1x 5” high performance
water-resistant woofer with rubber surround. High Frequency Section: 1x1”
polydome dynamic tweeter with built-in diffusion cap.
Crossover Frequency (internal passive): 7.4 kHz
Crossover Type & Slope: Internal passive; 12 dB/octave (2
nd order), High pass
for tweeter, and 6 dB/octave (1
st order) Low pass for woofer
Impedance (Z) for 8 ohms Thru connection: Nominal: 8 ohms
Minimum: 6.6 ohms
Input Connections: Spring-loaded push terminals
Transformer Taps (Transformer Input Mode): 70.7V taps: 16W, 8W, 4W, 2W
Caution: When using transformer input, an infra-sonic (high-pass) filter
should be used to prevent transformer saturation and overload. This will
increase reliability and decrease distortion. We recommend a setting of 80
Hz –3 dB point.

Especificaciones del producto

Marca: Peavey
Categoría: Vocero
Modelo: ISM 5Tx

¿Necesitas ayuda?

Si necesitas ayuda con Peavey ISM 5Tx haz una pregunta a continuación y otros usuarios te responderán


Vocero Peavey Manuales

Peavey

Peavey RBN 215 Manual de Usario

19 Septiembre 2024
Peavey

Peavey PVs 18 Manual de Usario

15 Septiembre 2024
Peavey

Peavey SP 218P Manual de Usario

14 Septiembre 2024
Peavey

Peavey S-12825 RB Manual de Usario

13 Septiembre 2024
Peavey

Peavey SSE 10 Manual de Usario

4 Septiembre 2024
Peavey

Peavey RBN 118 Manual de Usario

29 Agosto 2024
Peavey

Peavey PHR 860S Manual de Usario

27 Agosto 2024
Peavey

Peavey ISM 5Tx Manual de Usario

23 Agosto 2024
Peavey

Peavey PV 115D Manual de Usario

23 Agosto 2024
Peavey

Peavey RBN 110 Manual de Usario

20 Agosto 2024

Vocero Manuales

Últimos Vocero Manuales

Continental Edison

Continental Edison CELED53HP20V2B4 Manual de Usario

27 Octubre 2024
Canton

Canton Vento 830.2 Manual de Usario

27 Octubre 2024
Jamo

Jamo S7-25C Manual de Usario

27 Octubre 2024
Bowers Wilkins

Bowers Wilkins 707 S2 Manual de Usario

27 Octubre 2024
Monacor

Monacor GLS-301/GR Manual de Usario

27 Octubre 2024
Monitor Audio

Monitor Audio Silver C150 Manual de Usario

26 Octubre 2024
FBT

FBT MITUS 210M Manual de Usario

26 Octubre 2024
CyberData Systems

CyberData Systems SIP 011398 Manual de Usario

26 Octubre 2024
Lamax

Lamax PartyGo1 Play Manual de Usario

26 Octubre 2024
IKEA

IKEA SYMFONISK 405.847.50 Manual de Usario

26 Octubre 2024