Phanteks Glacier R220C Manual de Usario

Phanteks No categorizado Glacier R220C

Lee a continuación 📖 el manual en español para Phanteks Glacier R220C (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
MANUAL V1.0
STEP 1. OVERVIEW
PH-R160C_02/PH-R220C_02
INSTALLATION
PACKAGE CONTENTS
R160C or R220C
Fan Bracket
160/220 D-RGB strip
Stop Fitting
(pre-installed)
M4x25 Pump Screws
M4x10 Bracket Screws
M4x6 LED-strip Screws
Fan Screws
3mm Allen Key
D-RGB cable
D-RGB Motherboard cable
3x
4x
2x
2x
4x
STEP 2. INSTALL DDC PUMP
A. Remove the original DDC pump top.
B. Install the DDC pump using the M4x25mm screws
and the original O-ring.
FILL PORT
OUTLET
INLET
-DRAIN PORT
-SENSOR PORT
INLET-
DRAIN PORT-
SENSOR PORT-
Make sure the DDC pump is mounted
correctly and no cables are pinched.
M4x25mm
The R160C/R220C is equipped with multiple ports to
allow for more exibility. Please plan your water
loop before proceeding with installation.
DISCLAIMER - This product is intended for advanced users.
Please consult with a qualied technician for installation. Phanteks
assumes no liability for any damages occurring as a result of using
Phanteks cooling products.
WARNING - Power down the system before installation.
- Do not disassemble the reservoir. Warranty will be voided.
- Perform a leak test before turning on the system.
- Check our website for the latest installation guide.
GLACIER R220
GLACIER R160
DDC pump
4x
42mm pitch mounting holes
Tighten the pump screws evenly in a
diagonal pattern for an even pressure.
B.A.
The R160C/R220C can be used in 3 orientations:
MANUAL V1.0
STEP 3. INSTALL LED-STRIP AND BRACKET
STEP 5. MOUNT ON FAN
STEP 6. POWER ON
Daisy chain Phanteks D-RGB products D-RGB Motherboard Cable
MOTHERBOARD
D - R G B E A D EH R
M4x10mm
For optimal performance please check the following:
- Make sure the pump never runs dry.
- Close any unused ports with Stop Fittings.
- Always perform a leak test before turning on the system.
1. Choose the desired mounting alignment on your reservoir.
2. Place the LED-strip on the bracket with the LED’s facing the reservoir.
3. Use two M4x10 Bracket screws to secure the bracket to the reservoir.
4. use two M4x6mm screws to secure the LED-strip.Optional:
The bracket can be mounted directly to a 120 or 140mm fan with the four
included Fan Screws.
- Make sure all connectors and ttings are tightened.
- Connect the pump to a power source.
- Fill the reservoir and let the pump run until all air is released.
2x
1
2
3
4
5
M4x6mm
2x
M4x10mm
Connect D-RGB LED-strip to D-RGB motherboard and Phanteks products:
STEP 4. CONNECT D-RGB LIGHTING
Connect D-RGB cable:
4x
Let the pump run for multiple hours. Tilting the system
can help to release air bubbles.
Thanks to the 42mm pitch mounting holes you can install the
reservoir on many pump brackets such as the “Universal
Pump Bracket” from Phanteks. It is included with many Phanteks
cases and available separately.
Adjust the vertical position of the bracket to nd the perfect
position in your system. Both the bracket and the reservoir has
multiple mounting holes to move the position up and down.

Especificaciones del producto

Marca: Phanteks
Categoría: No categorizado
Modelo: Glacier R220C

¿Necesitas ayuda?

Si necesitas ayuda con Phanteks Glacier R220C haz una pregunta a continuación y otros usuarios te responderán




No categorizado Phanteks Manuales

No categorizado Manuales

Últimos No categorizado Manuales