Premier Mounts MM-BE426 Manual de Usario
Premier Mounts
soporte de panel plano
MM-BE426
Lee a continuación 📖 el manual en español para Premier Mounts MM-BE426 (2 páginas) en la categoría soporte de panel plano. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Page 1 Installation Instructions
Installation Instructions
9531-000-041-00
Parts List
MM-CB2
Dual Multi-Monitor Mounting Arm
(Qty 1)
The MM-CB2 is a dual multimonitor mount arm that works with any
2” tubing. Each mounting head provides 90° of omnidirectional tilt.
The mounting heads include both 75x75mm and 100x100mm VESA
mounting patterns. The arm includes integrated cable management
tabs to keep wires and cables protected and organized. The mounting
heads can be horizontally adjusted.
Step 1
1. Slide your mounting arm over the pole and base (Figure 1)
(not included, but should be previously installed).
Determine the position on the pole desired for your mounting arm.
2. Once in desired position,tighten the two (2)
pre-intalled M8 x 6mm set screws in the
holes in the back of the MM-CB2. Tighten
with included allen key (Figure 2).
Step 2
M4 x 10mm Combo Screws
(Qty 8)
Introduction
MM-CB2
(Figure 1)
(Figure 3)
Are you installing to a 75x75mm or
100x100mm VESA moutning pattern?
For 75x75mm, use mounting points A. For
100x100mm use points B in gure 3.
1) Thread the M4 screws to one-half of their
length into the top two mounting holes on
each display, but do not tighten the M4
screws at this time.
Step 3
(Figure 2)
A A
A A
B B
B B
Thread Insert in Flat
Panel or Adapter Plate
M4 Screw Partially
Threaded Into Flat Panel
Keyhole Slot
MM-CB2 Mount
1) Insert the heads of the M4 screws through the keyhole slots on the
mounting head (Figure 5).
2) Insert the remaining two (2) M4x10mm screws, into the bottom mounting
points (Figure 4)
3) Repeat sub-steps 1 & 2 for the second display.
4) Tighten all M4 screws.
Do not overtighten the mounting hardware
Figure 4
Figure 5
Step 4
To adjust the position of your displays horizontally
1. Turn the mounting head adjustment knob counter clockwise until the
mounting head is lose enough to slide easily along the pole.
2. Slide the display (or mounting head) to the desired position.
3. When in place, turn the adjustment head clockwise to tighten it. Make sure
it is completely secure and does not move before you move on to the next
display or nish.
4. Repeat steps for other displays if desired.
Loosen
& Adjust
Tighten
& Secure
5/32” Allen Key
(Qty 1)
Socket Wrench
(Qty 1)
4” Cable Ties (Qty 2)
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | +44 (0) 2476 644105 | F +44 (0) 2476 644165
Page 2 Installation Instructions
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of the
original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will be
shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS,
PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM
IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER MOUNTS
IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED
TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE
PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the
address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer
purchaser must accompany all warranty claims. Warranty claims must also include a description of the problem,
the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier Mounts
Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS
WHICH VARY FROM STATE TO STATE.
Step 4
To adjust the tension and/or tilt angle of the mounting head:
1) Adjust the mounting head by utilizing the 90 continuous tilt, until it is in the °
desired position.
2) Remove the side and bottom cosmetic cap from the mounting
head (Figure 6)
3) Use the supplied socket wrench to tighten both nuts.
4) The side nut secures the tilt position (Point A), while the bottom nut secures
the pivot (Point B).
Do not overtighten the mounting hardware
A
B
(Figure 6)
Bottom View
Installation Instructions
3100 E. Miraloma Avenue, Anaheim, CA 92806 | 800.368.9700 USA | F 800.832.4888 | www.mounts.com
Unit 3, The Moorings Business Park, Channel Way | Longford, Conventry, CV6 6RH, UK | +44 (0) 2476 644105 | F +44 (0) 2476 644165
Especificaciones del producto
| Marca: | Premier Mounts |
| Categoría: | soporte de panel plano |
| Modelo: | MM-BE426 |
¿Necesitas ayuda?
Si necesitas ayuda con Premier Mounts MM-BE426 haz una pregunta a continuación y otros usuarios te responderán
soporte de panel plano Premier Mounts Manuales
1 Septiembre 2024
1 Septiembre 2024
1 Septiembre 2024
1 Septiembre 2024
31 Agosto 2024
31 Agosto 2024
30 Agosto 2024
30 Agosto 2024
30 Agosto 2024
30 Agosto 2024
soporte de panel plano Manuales
- soporte de panel plano Samsung
- soporte de panel plano HP
- soporte de panel plano Abus
- soporte de panel plano Acco
- soporte de panel plano Icy Box
- soporte de panel plano Hitachi
- soporte de panel plano SilverStone
- soporte de panel plano 3M
- soporte de panel plano GPX
- soporte de panel plano Manhattan
- soporte de panel plano Vision
- soporte de panel plano Kensington
- soporte de panel plano Nec
- soporte de panel plano Techly
- soporte de panel plano BlueBuilt
- soporte de panel plano Da-Lite
- soporte de panel plano Luxor
- soporte de panel plano Steren
- soporte de panel plano Iiyama
- soporte de panel plano Barkan
- soporte de panel plano Digitus
- soporte de panel plano Insignia
- soporte de panel plano Sanus
- soporte de panel plano Peerless-AV
- soporte de panel plano Vogels
- soporte de panel plano Fellowes
- soporte de panel plano Planar
- soporte de panel plano Sven
- soporte de panel plano Konig
- soporte de panel plano Valueline
- soporte de panel plano One For All
- soporte de panel plano Ematic
- soporte de panel plano Newstar
- soporte de panel plano Ewent
- soporte de panel plano BakkerElkhuizen
- soporte de panel plano Ultimate
- soporte de panel plano Wentronic
- soporte de panel plano Peerless
- soporte de panel plano Proaim
- soporte de panel plano Monoprice
- soporte de panel plano Chief
- soporte de panel plano Ergotron
- soporte de panel plano Gabor
- soporte de panel plano Konig & Meyer
- soporte de panel plano Premier
- soporte de panel plano Atdec
- soporte de panel plano StarTech.com
- soporte de panel plano SIIG
- soporte de panel plano Bell'O
- soporte de panel plano B-tech
- soporte de panel plano Speaka
- soporte de panel plano Crimson
- soporte de panel plano Kogan
- soporte de panel plano Panduit
- soporte de panel plano Schwaiger
- soporte de panel plano Cabstone
- soporte de panel plano Elite Screens
- soporte de panel plano V7
- soporte de panel plano Kondator
- soporte de panel plano Bretford
- soporte de panel plano SmartMetals
- soporte de panel plano Unicol
- soporte de panel plano Equip
- soporte de panel plano Zaor
- soporte de panel plano Dataflex
- soporte de panel plano Multibrackets
- soporte de panel plano Anthro
- soporte de panel plano AMX
- soporte de panel plano Rocstor
- soporte de panel plano CTA Digital
- soporte de panel plano Amer
- soporte de panel plano Avteq
- soporte de panel plano Walker Edison
- soporte de panel plano My Wall
- soporte de panel plano Mount-It!
- soporte de panel plano LTN Technologies
- soporte de panel plano Heckler
- soporte de panel plano Helder
Últimos soporte de panel plano Manuales
27 Octubre 2024
15 Octubre 2024
15 Octubre 2024
4 Octubre 2024
2 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024