Projecta HDBT350 Manual de Usario

Projecta No categorizado HDBT350

Lee a continuación 📖 el manual en español para Projecta HDBT350 (8 páginas) en la categoría No categorizado. Esta guía fue útil para 13 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/8

Tray Fitting Instructions to suit Auxiliary battery for

Holden Colorado & Colorado 7

Years: 2011 onwards

Models: RGD 2.8 Litre Diesel

HEAVY DUTY DUAL BATTERY TRAY

P/No. HDBT350

IMPORTANT SAFETY INFORMATION

Please read this instruction thoroughly before fitting the tray.

This product is recommend to be fitted by a workshop or qualified mechanical person.

WARNINGS

• Before installation, make sure that the vehicle is stationary and the wheels chocked.

• Be careful when laying wires, not to cause any electrical shorts or wire breakage.

• After installation ensure the bonnet can close without hitting the newly installed battery

and battery tray.

SPECIFICATIONS

Max Battery Size (mm) L265 x W174 X H200

Max Battery Weight 19.6Kg

Recommended batteries Optima D34 & Exide Orbital

(Fully Sealed AGM type due to close proximity to wiring and computer)

Approximate fitting time 2 hours

Special tools Right Angle Drill

Recommended Dual P/n: IDC25, DBC150, VSR200

Battery System

Tray Location Engine Bay, Passenger side near firewall

KIT INCLUDES

Hardware

7 x M6 Bolts

1 x M6 Bolt Long

4 x M6 Nuts

1 x M6 Washer

2 x M8 Bolts

1 x M8 Nut

1 x M8 Body Washer

*Need to supply

1 x Cushion Clamp

2 x M6 RIVNUTS are

for isolator mount

Hardware

3 x M6 Bolts Counter Sunk

2 x M6 Bolts, Hex head Short

4 x M6 Nuts

1 x M6 Body Washer

Special Top

Mount

Tray

Isolator

Mount

Bolt Bracket

Right Angle

Bracket

T Bracket

J Bolts

Computer Mount Bracket for late 2013 models

FITTING INSTRUCTIONS

1. Make sure that the vehicle is stationary, the engine is switched off and cool.

Disconnect the negative and positive battery terminal from the main battery.

2. Remove the original battery & battery tray and 1 bolt only from the computer

mount closest to the tray.

3. Disconnect multi-pin plug behind computer and move to fit along firewall and

secure (Temporarily).

4. To allow clearance of the new battery tray.

a. You may need to bend L bracket on firewall.

b. Manipulate air-con pipe.

c. Unclip the loom behind factory tray.

5. Fit Tray with lower arm between brake lines and inner guard.

6. Place 3 x M6 Bolts through special bolt bracket then into the existing holes on the

inner guard, now push the bolts through the lower arm of the tray and hand

tighten M6 Nuts.

7. Place 2 x M6 Bolts into plate on the front of tray. Do not tighten yet. If fitting

this to a July 2012 or older Colorado go to step 12. Follow these steps for

August 2012 onwards.

Especificaciones del producto

Marca:	Projecta
Categoría:	No categorizado
Modelo:	HDBT350
Color del producto:	Chrome, Green
Ancho:	63 mm
Profundidad:	82.6 mm
Altura:	63 mm
Longitud del cable:	6.1 m
Amable:	Microfoon voor podiumpresentaties
Tecnología de conectividad:	Bedraad
Conexión:	6.35 mm (1/4")
Frecuencia del micrófono:	100 - 50000 Hz
Impedancia de entrada del micrófono:	100000 Ohm
Peso del micrófono:	737 g