Pyle PLMRC400X4 Manual de Usario

Pyle receptor PLMRC400X4

Lee a continuación 📖 el manual en español para Pyle PLMRC400X4 (12 páginas) en la categoría receptor. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/12

4-Channel Weather-Resistant Audio Amplifier System

PLMRC400X4

Class D Compact Designed Suit for Car, ATV,

UTV, 4X4, Jeep, Motorcycle and Marine,

and any other Weather Resistant Application

www.PyleUSA.com

INTRODUCTION

This power amplier has been designed to provide high quality performance

with a minimum of maintenance. However, it's performance will only be as good

as the care and quality of components with which is installed.

We therefore advise that you read these instructions very carefully to familiarize

yourself with the product and it's features.

Before installing the power amplier please read this instruction manual

carefully. The instructions for mounting and connecting the set have to be

followed precisely. If necessary, a service center should be consulted.

All connections for DC power, signal input and speaker outputs can be carried

out easily and safely byway of RCA and screwed terminals.

INSTALLATION INSTRUCTIONS

Please choose a mounting place without any direct weather inuences.

Note that the amplier generates heat so that a well ventilated place is necessary.

According to your car's construction the set can be made very carefully in order

to ensure the amplier's full performance and reliability.

Keep the wire connections as short as possible with sucient dimensions in

order to minimize power losses and provide a higher audio output of the system.

For safety reasons route all power and speaker wiring by using the exiting wire

channels. To minimize damage to the cables, take care that they do not pass

sharp edged metal. Lay all cables as far away as possible from the ignition cables,

modules in the boot and under the key dashboard, as this create interference.

Add a fuse into the (+) power cable in a distance of not more than 30 cm from

the positive battery pole.

Keep the length of the power wires as short as possible. It is better to use power

cables which are short and then longer speaker cables.

In order to reduce interference, also pay attention to the instructions.

www.PyleUSA.com 3

PRECAUTIONS

• This unit is designed for negative ground 12-14.50 VoIts (DC) operation only

• Use speakers with an impedance of 2 or 4 Ohms (4 to 8 Ohm when used as

bridged amplier)

• Avoid installing the unit where:

•It would be subject to high temperatures, such as from direct sunlight or hot

air from the heater.

•It would be exposed to rain or moisture.

•It would be subject to dust or dirt.

• If your car is parked in direct sunlight and there is a considerable rise in

temperature inside the car, allow the unit to cool o before operation.

• When installing the unit horizontally, be sure not to cover the heatsink ns

with the oor carpet.

• If this unit is placed too close to the car radio, an interference may occur in this

case, separate the amplier from the car radio.

• This power amplier employs a protection circuit to protect the transistors and

speakers if the amplier malfunctions.

• Do not attempt to test the protection circuits by covering the heatsink or

connecting improper loads.

• Do not use the unit with a weak auto battery as its optimum performance

depends on a normal battery supply voltage.

• For safety reasons, keep the volume of your car audio system moderate so that

you can still hear normal trac sounds outside your car.

FUSE REPLACEMENT

If the fuse blows, check the power connection and replace the fuse. If the fuse

blows again after replacement, there may be an internal malfunction.

In this case, consult your dealer.

WARNING: Use the specied amperage fuse. Use of a higher amperage fuse

may cause serious damage.

PROTECTION CIRCUIT

This amplier is provided with a protection circuit which operates in the

following cases when:

• the unit is overheated.

• the speaker terminals are short circuited.

Especificaciones del producto

Marca:	Pyle
Categoría:	receptor
Modelo:	PLMRC400X4
Color del producto:	Black, Grey
Peso.:	903 g
Ancho:	240 mm
Profundidad:	420 mm
Altura:	60 mm
Amable:	Multifunctionele pan
Diámetro:	240 mm
Temperatura (máx.):	175 °C
Cantidad de embarcaciones:	1
Forma:	Rond
Material:	Roestvrijstaal
No contiene:	Perfluoroctaanzuur (PFOA)
Recubrimiento antiadherente:	Ja
Incluye tapa:	Nee
Aptas para el lavavajillas:	Nee
Material-del-mango:	Bakeliet
Recubrimiento interno:	Titanium
Apto para todo tipo de fuegos:	Ceramic, Gas, Halogen, Induction, Sealed plate
Indicador de calor:	Ja
Indicador-de-calor:	Thermo-Spot