Pyle PLMRSBA8 Manual de Usario

Pyle receptor PLMRSBA8

Lee a continuación 📖 el manual en español para Pyle PLMRSBA8 (5 páginas) en la categoría receptor. Esta guía fue útil para 10 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/5
PLMRSBA8
Marine Grade Slim Active Subwoofer
8” 600 Watts Low-Prole Active Amplied Marine
and Waterproof Subwoofer System
Suitable for Under-seat Installations
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: support@pyleusa.com
www.PyleUSA.com
2www.PyleUSA.com 3
Introduction
With the , we are introducing a low-prole amplied subwoofer. Low enough to PLMRSBA8
easily t below the seat of your car. This system oers you a quick and easy way to add a
high-powered subwoofer system to your audio system.
The integrated amplier in the features low pass crossovers, and a control forPLMRSBA8
adjusting the input sensitivity from 0.12V to 3.5V.
Both high level (speaker level) and low level (RCA type) inputs are present, making this a
universal solution for use with any head unit or other input source.
For further exibility in the use of a subwoofer, a variable bass boost control has been
included. You can control the subwoofer level with the remote level control module.
Mounting the Subwoofer
1. Find a suitable location in the vehicle in which to mount the amplier.
A typical location is shown below:
2. Make sure there is sucient air circulation around the intended mounting location.
3. Mark the location for mounting hole screws by positioning the cabinet where you wish to
install it. Make a small mark to identify the position and remove the unit. Thoroughly clean
the area you plan to attach the subwoofer, using a vacuum cleaner and press down on it
securely.
Vehicle seat
Control Panel and Features
1. POWER ON LED INDICATOR
2. PROTECT LED INDICATOR
3. PHASE SHIFT: Use this switch to help compensate for time alignment problems in the
system. Such problems usually result from having the subwoofer at a dierent distance
from the listener than the other speakers in the system.
4. AUTO POWER ON: In OFF mode, It’s not necessary to connect the remote cable if you’re
using the high level inputs. Do not function with the RCA inputs. However, we prefer the
direct remote wiring on a “plus after contact”.
5. LOW PASS FILTER: This control permits you dene the frequency range you want the
subwoofer amplier to receive. The subwoofer will reproduce all sound BELOW the
frequency you set. If the rest of your system is weak on the mids, you may wish to set this
control relatively high. If the midrange is well covered by the rest of your system, you will
probably want the subwoofer to only receive lower frequency signal.
6. BASS BOOST: The bass boost feature will increase the sound level the bass frequencies.
7. INPUT GAIN CONTROL: After you have installed your system, turn this control to minimum.
Turn the head unit on (and the subwoofer will turn on via the remote connection).
Turn the head unit volume to about 2/3 full level. Slowly turn up the subwoofer input gain
control until you hear a small amount of distortion. Then reduce the level until the
distortion is completely gone. Leave the control at this setting.
8. REMOTE LEVEL CONTROL PORT: Attach the included remote level control to cotrol the
volume level of the subwoofer independently.
9. HIGH LEVEL (speaker level) INPUTS: If your head unit does not have RCA outputs, you
can use the speaker outputs for the audio source for the PLMRSBA8. Use the supplied cable
and connect the outputs properly as shown in the connection diagram in this manual.
10. LOW LEVEL RCA INPUTS: Low level inputs are the recommended way to introduce the
audio signal to the subwoofer if RCA outputs are present on your head unit or other
signal source (such as a sound processor).
11. FUSE: The fuse is rated at 25A. Do not use a fuse with a dierent value and NEVER replace
the fuse with a wire or coin.
12. POWER TERMINALS
3
1 2 54 6 7 8 9 10 11 12
www.PyleUSA.com
4www.PyleUSA.com 5
Low Level Input Wiring
Low-level (RCA) input wiring is preferred for best audio performance.
Most trunk or hatchback installations will require a 15-20 foot RCA cable, while pickup trunks
and under-seat installations will require a 6-12 foot RCA cable. Always use a high quality
cable.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
High Level Input Wiring
The high level input(s) should only be used when your receiver lacks RCA outputs.
If the RCA outputs are not present, connect the speaker outputs from the receiver to the
high level input connector of the amplier. Be sure to observe polarity to avoid audio phase
problems.
NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your
amplier at the same time!
Power Connections
Connect the ground terminal to the closest point on the chassis of the vehicle.
Keep this ground wire to less than 39” (100 cm) inlength. Use 8 gauge (or heavier) wire.
Connect the remote terminal to the remote output of the head unit using 16 gauge
(or heavier) wire. Connect an empty fuse holder within 18” (45 cm) of the car battery, and run
8 gauge (or heavier) cable from this fuse to the amplier location. Then connect the fuse
holder to the “ ” connection on the subwoofer rear panel.BATT+
Remote Level Control Connection
To Audio outputs of head
unit or signal processor
White L+ Black L-
Grey R+ Black R-
To Speaker Terminals
of head unit
Chassis
ground
point
To REMOTE TURN-ON
terninal of head unit
FUSE
+
Remote
Level Control
Instal the remote control securely under the
dash or in a similar location where using it will
not distract the driver.

Especificaciones del producto

Marca: Pyle
Categoría: receptor
Modelo: PLMRSBA8

¿Necesitas ayuda?

Si necesitas ayuda con Pyle PLMRSBA8 haz una pregunta a continuación y otros usuarios te responderán


receptor Pyle Manuales

Pyle

Pyle PFMRA340BB.5 Manual de Usario

17 Octubre 2024
Pyle

Pyle PLA2200 Manual de Usario

30 Septiembre 2024
Pyle

Pyle PTAU45.5 Manual de Usario

22 Septiembre 2024
Pyle

Pyle PWMA3003BT Manual de Usario

21 Septiembre 2024
Pyle

Pyle PDC22 Manual de Usario

19 Septiembre 2024
Pyle

Pyle Pro PTAU23 Manual de Usario

18 Septiembre 2024
Pyle

Pyle PFA320BT Manual de Usario

18 Septiembre 2024
Pyle

Pyle PTAUWIFI46 Manual de Usario

16 Septiembre 2024
Pyle

Pyle PPG-460A Manual de Usario

13 Septiembre 2024
Pyle

Pyle PLAM2001D Manual de Usario

12 Septiembre 2024

receptor Manuales

Últimos receptor Manuales

Crown

Crown CDi DriveCore 2|300BL Manual de Usario

27 Octubre 2024
Boss

Boss PT3000 Manual de Usario

27 Octubre 2024
Speco Technologies

Speco Technologies PBM120AT Manual de Usario

27 Octubre 2024
Fosi Audio

Fosi Audio V3 Manual de Usario

26 Octubre 2024
Jensen

Jensen CAR710-4BC Manual de Usario

25 Octubre 2024
Onkyo

Onkyo TX-RZ830 Manual de Usario

24 Octubre 2024
Pioneer

Pioneer VSX-1122K Manual de Usario

22 Octubre 2024
Yamaha

Yamaha HTR-5072 Manual de Usario

21 Octubre 2024
NAD

NAD C 355BEE Manual de Usario

20 Octubre 2024
Yamaha

Yamaha RX-A810 Manual de Usario

20 Octubre 2024