Qazqa 90502 Manual de Usario

Qazqa Alivio 90502

Lee a continuación 📖 el manual en español para Qazqa 90502 (4 páginas) en la categoría Alivio. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/4

Dark WL III PIR LED Solar

MODEL: 90502

HOW TO DETERMINE WHERE TO MOUNT YOUR SOLAR

PIR SENSOR LIGHT

Please be noted that: DIRECT SUNLIGHT is important for the opera-

on of SOLAR PIR SENSOR LIGHT. The more direct sunlight the solar

cell receives in dayme, the longer the light will operate.

Main Unit:

The main unit contains the lamp (2pcs 0.5W LED), moon sensor and

baery (NI-MH Rechargeable baery, 3.6V, 600mAh). When determi-

ning where to mount this unit, please consider that the moon

sensor with detecon scope of max. 8 meters (in front of the light)

and about 120º (horizontal) at 25℃ environmental temperature. The

detecon range of the unit may alter with temperature change, the

mounng height and locaon. All Passive Infra-Red detectors are

more sensive in cold and dry weather than warm and humid

weather.

To mount the unit vercally as a security light, aach the unit to a

solid surface as shown in ﬁgure . Use the two screws provided in the

package.

Solar Cell:

The solar cell is one of the main power source for the SOLAR PIR

SNESOR LIGHT. It converts the sunlight’s energy into electricity that

charges the baery in main unit. It requires DIRECT SUNLIGHT onto

the surface of solar cell for as long as possible during the dayme.

Use the two screws provided in the package to mount the solar cell

unit onto a solid surface. Make sure it is ﬁxed into the solid surface.

You can adjust the angle of the solar cell. It should face as much

DIRECT SUNLIGHT as possible during the dayme.

At last route the solar cell’s power cord to the main unit and plug it

into the the side hole for solar cell.

FINAL ADJUSTMENT AND START-UP

Aer you successfully installed your SOLAR PIR SENSOR LIGHT, you

are almost ready for carefree operaon with a few ﬁnal steps:

Inial 2-days Charge:

On the main unit there is a switch with 2 posions:

● OFF ● ON

ON —

Posion for normal operaon

OFF ---

1) Posion for delivery or long periods of non-use

2) Posion for inial 2-day charge before ﬁrst adjustment and use.

Then, turn the slide switch to OFF posion. The solar cell will charge

the baery without acvang the unit. Leave the switch in this posi-

on for 2 sunny days to ensure that the baery has a full charge for

moon sensor adjustment and normal operaon.

HOW TO ADJUST THE MOTION SENSOR

Aer the inial 2-day charge, turn the switch to AUTO posion.

On the moon sensor there are two adjusng knobs: TIME / LUX

1) TIME --- Duraon me: For how long you

wish the light to run aer moon is

detected in the ﬁeld, the duraon me is

from 10 seconds to 1 minute adjustable.

Note: Once the light is acvated by the PIR

sensor, any subsequent detecon will restart

the med period again from the beginning.

Ø6mm

30mm

Ø6x27mm

M4x30mm

87.8

40.00

76.00

42.30

Ø6mm

30mm

42.30

Ø6mm

30mm

7 8

3 4 5

207 mm

106 mm

157 mm

93 mm

185 mm

54 mm

2) LUX – Lux control level: The Lux control module has a built-in sen-

sing device (photocell) that detects daylight and darkness. ( )

posion denotes that the loading will be turned on by PIR during

day and night, ( ) posion denotes that the loading will be

turned on by PIR only at night. You can set desired level to run the

unit the by adjusng the LUX knob.

Note: If, in daily posion, the unit turns on when it is too light out-

side, turn the control towards ( ). however, if the light is not acva-

ng during nighme because of a street light or bright house light,

turn this control towards ( ).

Walking-test:

Point the moon sensor to face the area you want to detect moon

in and set the TIME knob to minimum (-) posion and LUX knob to

“light”( ) posion. Walking slowly in its detecon area, the sensor

can detects moving invisible infra-red radiaon given oﬀ by a human

body and then turn on the light. Test the coverage of the area by

walking slowly around unl not to switch on the light.

ADJUSTMENT OF THE LAMP HOUSING:

Point the lamp housing to face the area you wish to illuminate.

GENERAL ELECTRICAL AND SAFETY WARNINGS

1) Do not cut the solar cell wire. Disconnue use if the wire becomes

frayed or broken.

2) Do not immerse components in liquid.

3) Do not use any other charge than the single solar charging panel

provided with the SOLAR PIR SENSOR LIGHT. This may result in

injury or damage to the light and voids any warranty.

4) Posion so that the cord is securely fastened and will not result in

a hazard (such as tripping).

5) When changing the baery, be careful of any sharp edges that

could cut you or the wires. Do not pull on wires.

CLEANING

It is important that the solar panel is kept free of dirt and debris. A

dirty solar panel will not allow the baery to fully charge and this will

shorten the life of baery and cause the light to malfuncon.

STORAGE

If you wish to store your light indoors for more than two or three

days, follow these steps to prevent damage to baery:

1. Turn the switch to OFF posion

2. Store the light and solar panel where it can receive some sunlight

Especificaciones del producto

Marca:	Qazqa
Categoría:	Alivio
Modelo:	90502
Color del producto:	Wit
Peso.:	94 g
Ancho:	60 mm
Profundidad:	66 mm
Altura:	104 mm
Manual de usuario:	Ja
Indicadores LED:	Ja
Tipo de embalaje:	Doos
Modos de vídeo compatibles:	720p
Iluminación mínima:	0.01 Lux
tipo LED:	IR
Velocidad de fotogramas máxima:	- fps
Tamaño del sensor óptico:	1/3 "
Megapíxeles:	1.3 MP
Resolución máxima de imagen:	1280 x 960 Pixels
Tipo de sensor de imagen:	CMOS
Resolución máxima de vídeo:	1280 x 960 Pixels
balance de blancos:	ATW, AWC, Auto, Indoor, Manual, Outdoor
Resoluciones de gráficos compatibles:	1280 x 720 (HD 720)
Conecta y reproduce:	Ja
Reducción de ruido:	Ja
Visualización en pantalla (OSD):	Ja
Número de idiomas de visualización en pantalla:	11
Función de detección de movimiento:	Ja
El consumo de energía:	212 mA
Abarcando:	12 V
Exploración progresiva:	Ja
Relación señal-ruido:	60 dB
Modo día/noche:	Ja
Función de foto:	Ja
Alcance de visión nocturna:	10 m
Número de iluminación LED:	18
Compensación de retroiluminación:	Ja
Número de píxeles efectivos (H x V):	1280 x 960 Pixels
Tipo de lente:	Gaatje
Temperatura de funcionamiento (TT):	-10 - 50 °C
Máscara zona privada:	Ja
Diámetro de la lente:	3.7 mm
Tecnología de reducción de ruido:	2D noise reduction, 3D noise reduction
Supresión de resaltado BLC (HSBLC):	Ja
Activar/desactivar desempañado:	Nee