QTX QR12K Manual de Usario

QTX Vocero QR12K

Lee a continuación 📖 el manual en español para QTX QR12K (4 páginas) en la categoría Vocero. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
QRK
Active Speaker Cabinets
Order ref: QR8K (178.310UK)
QR10K (178. ) 311UK
QR12K (178.313UK)
QR15K (178.316UK)
User Manual
Version 1.1
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
QRK Active Speaker User Manual
Introduction
Thank you for choosing the Q active speaker as part of your sound system This speaker is designed tRK . o
offer clear and reliable sound reinforcement for leisure and entertainment applications.
Package Contents
Please check the contents to ensure that the product has been received in good condition with the
appropriate mains lead(s). If you find any accessory is missing or the product has arrived with any
problems, please contact your retailer at once.
Warning
This product contains no user-serviceable parts so make no attempt to try to fix or modify this item
yourself as this will invalidate the warranty. We recommend you keep the original package and proof of
purchase for any possible replacement or returned demand. To prevent the risk of fire or electric shock, do
not expose this appliance to rain or moisture. To prevent electric shock do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service personnel.
Safety: Labelling Conventions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
This symbol indicates that dangerous voltage constituting a risk of electric shock
is present within this unit
This symbol indicates that there are important operating and maintenance
instructions in the literature accompanying this unit.
Prior to connecting mains, check the supply voltage is correct and the mains lead is OK.
Avoid ingress of water or particles into the enclosure.
If the mains fuse blows continually, refer the unit to qualified service personnel.
Placement
Keep the unit out of direct sunlight and away from heat sources.
Keep the unit away from moisture or dusty environments.
Mount the cabinet on a stable surface, 35mm pole mount or suspend using the integral flying points.
Ensure that any supporting structures have adequate load capacity for the weight of the uni t.
Cleaning
Use a soft cloth with a neutral detergent to clean the cabinet, panel and controls.
To avoid damage, do not use solvents to clean this equipment.
QRK Active Speaker User Manual
Rear Panel Layout
Setup & Operation
Before connecting any leads, ensure that the POWER switch (12) is in the OFF position.
MIC VOL, LINE VOL and VOLUME controls (2, 6, 7) should be turned fully down.
TONE or BASS and TREBLE controls (1, 4, 5) should point vertically (12-o-clock position ).
For QR12K and QR15K, the ECHO control (3) should be turned fully off.
Connect any microphones to be used via the 6.3mm jack input(s) on the rear panel (7).
Connect any line level input to the RCA LINE connectors on the rear panel (9). Since both RCA
connectors are parallel to mono input, one can be used for input and the other to connect ed a
the line signal to additional active cabinets. If a complete mix including microphones is to be on
fed onto further cabinets, this can be connected from the MIX OUT RCA connectors (10).
The QR12K and QR15K models have a SPEAKER OUT connector (14). This may be connected
to a passive speaker which has a minimum impedance of 8Ω and a power handling of 90W.
QR12 or QR15 passive models (178.212UK, 178.213UK) are recommended extension speakers.
Using the mains lead provided (or a suitable equivalent), connect the IEC or Fig.8 inlet to the
mains, ensuring correct voltage and that the outlet is earthed (for IEC connection).
Press the power switch on and gradually increase the VOLUME or LINE VOL control (2, 6),
whilst playing the line signal into the input. Check the output from the speaker and any
connected extension speakers. Alternatively, for microphone inputs, gradually increase the MIC
VOL control (7) and test the microphone(s) for output through the speaker. Once all outputs
are checked, increase controls to deliver the maximum required level.
1. TONE control for main output
2. LINE VOL level for line inputs
3. ECHO effect level for mics
4. TREBLE control for main output
5. BASS control for main output
6. VOLUME control for main output
7. MIC VOLUME for mic inputs
8. MIC inputs 6.3mm jack (unbal)
9. LINE IN (parallel OUT) RCA
10. MIX OUT RCA main outputs
11. POWER LED indicator
12. POWER ON/OFF switch
13. FIG.8 mains inlet
14. SPEAKER OUT cab to 8Ω ext.
15. IEC mains inlet & fuse holder

Especificaciones del producto

Marca: QTX
Categoría: Vocero
Modelo: QR12K

¿Necesitas ayuda?

Si necesitas ayuda con QTX QR12K haz una pregunta a continuación y otros usuarios te responderán




Vocero QTX Manuales

Vocero Manuales

Últimos Vocero Manuales