Rangemaster LU9852 Manual de Usario
Rangemaster
Hundir
LU9852
Lee a continuación 📖 el manual en español para Rangemaster LU9852 (4 páginas) en la categoría Hundir. Esta guía fue útil para 17 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/4
Instructions for Cubix, Cubix Gemini & Lunar
COMPOSITE INSET SINKS
WITH FIXED POSITION CLIPS
Installation Instructions
&
Aftercare Information
INSTALLATION
Installer
Please leave this leaet with the user, as it contains valuable
after care advice.
Notes
During installation, take care to protect the sink
from scus and scratches.
Avoid straining and overtightening of all plumbing
xtures connected to the sink.
Carefully check that the moulding and edges of the
sink are dead level so that water will ow o the
drainer.
We recommend that the worktop opening is sealed
using waterproof sealant, paint or a similar material.
The clamping brackets are suitable for worktops of
between 28–40 mm thickness. If your worktop is a
dierent size then it may require packing under the
clips or rebating.
Preparing the Worktop
Marking out the opening
We recommend that you t the inset sink to the worktop
before permanently xing the worktop to the cabinet.
1. Place the sink upside down on the worktop. Position
the sink on the worktop as required. Make sure the
cabinet framework will clear all parts of the sink. Using a
soft, sharp pencil draw around the sink as accurately as
possible (Fig.1). Remove the sink.
Alternatively, you can use a sink template. For details go
to www.rangemaster.co.uk.
2. Draw another line 10mm inside the sink top outline –
this is the cutting line for the opening (Fig.2).
3. Drill as large a hole as possible inside the cutting line.
Using a padsaw, jigsaw or similar, cut out the opening
up to the cutting line.
Preparing the sink
Drilling a taphole
Before drilling please read safety instructions
supplied with hole saw.
The front face must be fully supported to prevent
cracking when drilling or cutting.
WARNING!
Composite sink products include a silica ller. Any
machining operation will produce ne particles of
dust. Drilling or cutting be carried out in a MUST
well-ventilated area.
Worktop
Final position
of sink
Cutting line for opening
10 mm
Fig.1
Fig.2
Due to our policy of continual improvement, we reserve the right to change specications without prior notice.
Fig.3
Fig.4
If a taphole is required, but has not been supplied in the sink,
proceed as follows:
1. Decide whether the bowl is to be left or right handed
when the sink is tted. You will require a 35 mm hole
saw (supplied with selected products).
2. On the reverse side of the sink you will nd a location
point for tap cut-out (Fig.3).
3. Using the 35 mm hole saw, carefully cut out the tap
hole.
Fitting the clips
There are two methods of tting the clips:
• Screw down xing or,
• Pin xing
Screw down xing
1. Using the screws supplied, t the mounting clips to the
sink (Fig.4).
2. Hinge the clips away from the sink edge.
Pin xing
1. Position the clips over the pins molded in the sink. Pull
and twist the clip towards the edge of the sink (Fig.5)
until it snaps into place.
2. If a clip is tight then, using a at screwdriver, tap on the
base until it snaps into place (Fig.6).
3. Hinge the clips away from the sink edge.
At this stage, test t the sink in the worktop opening. You may
need to enlarge the opening around the clips.
Fit the tap and waste ttngs to the sink using the instructions
supplied with them.
Fitting the seal or sealant
There are 2 methods of sealing your sink to the worktop:
• Foam seal or,
• Silicon sealant
Foam seal
Peel o the backing strip and stick the seal to the recess in
the sink (Fig.7). Make sure that a neat butt joint is achieved
where the ends of the seal meet.
Silicon sealant
Apply silicone sealant (not supplied) to the underside of the
sink rim (Fig.8).
Fitting the sink
1. Turn the sink upside down and lay the worktop over
the sink. Swing each clip into place (Fig.9) – this is the
most eective method, although if the worktop has
been tted to the cabinet the sink can be placed in the
opening and xed in position from underneath.
2. Centre the sink. Tighten the xing screws.
DO NOT tighten fully at rst attempt.
Remove any surplus sealing material or wipe away any excess
sealant.
Tap on clip base with
a at screwdriver
Fig.5
Fig.6
Fig.7
ArtNo.512-0001 - Gemini applying sealant
Fig.8
SinkWorktop
1 2 3
Fig.9
Especificaciones del producto
| Marca: | Rangemaster |
| Categoría: | Hundir |
| Modelo: | LU9852 |
¿Necesitas ayuda?
Si necesitas ayuda con Rangemaster LU9852 haz una pregunta a continuación y otros usuarios te responderán
Hundir Rangemaster Manuales
16 Octubre 2024
1 Octubre 2024
2 Agosto 2024
Hundir Manuales
- Hundir Smeg
- Hundir Teka
- Hundir Hotpoint-Ariston
- Hundir Kernau
- Hundir Concept
- Hundir CDA
- Hundir Blanco
- Hundir Gustavsberg
- Hundir Franke
- Hundir Leisure
- Hundir Nodor
- Hundir Elkay
- Hundir Schock
- Hundir Caple
- Hundir Roca
- Hundir Foster
- Hundir Advance Tabco
- Hundir Sani-Lav
- Hundir Deante
- Hundir Artusi
- Hundir Kuchinox
- Hundir Oliveri
- Hundir Shaws
Últimos Hundir Manuales
14 Octubre 2024
13 Octubre 2024
13 Octubre 2024
13 Octubre 2024
13 Octubre 2024
5 Octubre 2024
4 Octubre 2024
4 Octubre 2024
3 Octubre 2024
2 Octubre 2024