Remington XR1391 Manual de Usario

Lee a continuación 📖 el manual en español para Remington XR1391 (14 páginas) en la categoría Maquinilla de afeitar. Esta guía fue útil para 12 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/14
$
Face Saver: Pre-shave Powder Stick
SP4
SP5 $11.95 AUD $14.95 NZD $
$
Shaver Saver: Aerosol Spray Cleaner $11.95 AUD $14.95 NZD
Article Price each
AUD
Price each
NZD Qty Amount
$
$
$
Sub Total
Postage &
handling
TOTAL
7.50
Replacement Shaving Head & Cutters for XR1391AU SPR-XRAU $37.95 AUD $49.95 NZD
$
Beard Trimmer Attachment for XR1391AU SPR-XTAU $37.95 AUD N/A
Remington is a Registered Trademark
of Spectrum Brands, Inc., or one
of its subsidiaries.
Spectrum Brands Australia Pty Ltd
Locked Bag 3004
Braeside, VIC 3195
Australia
CLEANING & MAINTENANCE
The shaver is a washable apliance. The head and body may be cleaned
under warm water.
NOTE: When cleaning your shaver, make sure the shaver is turned off and
disconnected from the power cord.
CAUTION:
When cleaning the external surfaces of the shaver, do not use strong
detergents or other chemicals.
To dry, wipe the surface of the shaver with a dry towel. Do not use a hair dryer
or heater to dry the shaver.
NOTE: The shaver head and neck assembly is designed to be detachable from the
shaver body. Simply pull upwards from the neck of the shaver for easy release.
To reattach neck, align it with the neck attachment cavity so that it clips back into
position.
Daily Cleaning:
1. Locate the detachment grooves on the head & cutter assembly. Gently pull to
detach the hair pocket from the neck assembly. (Diagram L)
2. Tap out excess hair shavings.
3. Rinse the head of the shaver in running water.
4. Gently reattach the hair pocket to the neck assembly until it locks in place on
all three sides. The hair pocket may be reattached in any conguration.
10
1. Head & cutter (hair pocket) assembly
2. Detachment grooves
3. Neck assembly
4. Neck attachment cavity
1234
Weekly Cleaning:
1. Perform the daily cleaning steps 1 and 2.
2. Remove the hair pocket from the head & cutter assembly. (Diagram L) Place
the body of the shaver aside.
3. Slide the blue cutter support frame upwards towards the direction of the two
cutters to release it from the assembly. (Diagram M)
4. Lift and remove the cutter support frame away from the cutters.
5. Remove the cutters. (Diagram N)
6. Thoroughly rinse away any debris from inner and outer cutters with warm
water.
7. Replace the inner cutters. (Diagram O) The inner and outer cutters are colour
coded (grey, blue and black) to ensure each cutter is returned to its original
and most effective position on the cutter assembly.
8. Hold the cutter support frame with the raised center section facing upwards.
Place it over the cutters so that the centre mouth opening is facing the blue
cutter. Slide the cutter carrier towards the blue cutter until the locking tab
locks under the centre triangle. (Diagram P)
9. Lubricate each cutter with Remington Shaver Saver (SP4).
10. Gently reattach the hair pocket to the neck assembly until it locks in place
on all three sides. The hair pocket may be reattached in any configuration.
(Diagram Q)
11
LM N O
Q
P

Especificaciones del producto

Marca: Remington
Categoría: Maquinilla de afeitar
Modelo: XR1391

¿Necesitas ayuda?

Si necesitas ayuda con Remington XR1391 haz una pregunta a continuación y otros usuarios te responderán




Maquinilla de afeitar Remington Manuales

Maquinilla de afeitar Manuales

Últimos Maquinilla de afeitar Manuales