Sani-Lav 705B Manual de Usario

Sani-Lav Hundir 705B

Lee a continuación 📖 el manual en español para Sani-Lav 705B (9 páginas) en la categoría Hundir. Esta guía fue útil para 7 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/9

A C O R B AT T E R Y P O WERE D

S I N K W I T H E L E C T R O N I C S E N S O R

Operating Manual for Hands-Free Wall Mount Stainless Steel Sink

AC Models 705A and 705A-0.5

Battery Models 705B and 705B-0.5

of Domestic and Foreign Parts

Columbia does not recommend use with harsh chemicals.

Product Compliance

NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Lead-Free Compliant, ASME A112.18.1

COLUMBIA SPECIFICATIONS

A C O R B AT T E R Y P O W E R E D

S I N K W I T H E L E C T R O N I C S E N S O R

800.626.2117 columbiasinks.com info@columbiasinks.com

Installation Instructions

Step 1

1. Establish sink location on the wall.

2. Determine desired height for the top of the backsplash from finished floor and draw a level

line which will be the top edge of the wall mounting bracket.

3. Hold the wall mounting bracket against the wall and mark the wall where the holes are. Drill

holes and secure bracket to the wall as shown in illustration A. Screws are not provided.

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Position the sink onto wall bracket.

2. Loosely attach support brackets under sink and push against wall then mark holes for

drilling as shown in illustration B.

3. Remove support brackets from sink and drill holes for mounting fasteners (not provided).

4. Re-mount support brackets to sink and fasten to wall.

Step 4

1. Connect waste line to strainer assembly (s).

2. Mount sensor control box at desired location on wall.

3. Connect power line from sensor to control box.

4. Attach supply tube from faucet to control box.

5. Connect hot and cold water from the source to mixing check valve (s).

6. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor

installation instructions)

7. Check connections for leaks.

8. Replace aerator onto the spout (s).

9. We recommend sealing top of backsplash to wall as shown in illustration C.

Parts List

(1) Wall mount sink

(1) AC or Battery powered sensor faucet assembly

(1) Wall-mounting bracket

(2) Support brackets

(4) Support bracket mounting bolts and washers

(1) Mixing check valve

(1) Strainer assembly with basket

Tools Required

Tape measure

Adjustable wrench

Drill motor and drill bits

Pipe wrench

Level

Safety glasses

Screw drivers: phillips and standard

Pencil

Socket wrench

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Go to for more information on replacement parts and installation videos.columbiasinks.com

Illustration A

Illustration B

Illustration C

COLUMBIA SPECIFICATIONS

A C O R B AT T E R Y P O W E R E D

S I N K W I T H E L E C T R O N I C S E N S O R

800.626.2117 columbiasinks.com info@columbiasinks.com

10in

254mm

10in

254mm

9.5in

241.3mm

7in

178.9mm

18.828in

478.2mm

R.75in

19.1mm

.75in

19.1mm

45deg

7.087in

180mm

Hole Conﬁguration

.875” [22mm]

dia. hole

10in

254mm

10in

254mm

3.25in

82.6mm

4in

100mm

Front Side

Top

2”

(51mm) .875”

(22.22mm)

Back

Splash

.375”

dia. hole

Wall-mounting

bracket

6.25in

158.8mm

14”

(355.6mm)

2in

50.8mm

14in

355.6mm

1.5in

38.1mm

17.5in

444.5mm

2” drain

hole

R.5in

12.7mm

6in

152.4mm

20in

508mm

1.5in

38.1mm

17in

431.8mm

Wall Mounting Detail

Especificaciones del producto

Marca:	Sani-Lav
Categoría:	Hundir
Modelo:	705B
Color del producto:	Zwart, zilver
Pantalla incorporada:	Ja
Amable:	DECT-telefoon
Cargador:	Ja
Método de montaje:	Bureau
Vocero:	Ja
apoyar:	Ja
Identificador de llamadas:	Ja
Posible conferencia telefónica:	Ja
Control del volumen:	Digitaal
Incluye estación base:	Ja
Teclas retroiluminadas:	Ja
Color de retroiluminación:	Blauw
Escribe tono de llamada:	Polyfonisch
Reloj con calendario:	Ja
Tonos polifónicos:	Ja
Intercomunicador:	Ja
Capacidad de la agenda telefónica:	50 entries
Identificador de llamadas para llamada en espera:	Ja
Llama de nuevo:	Ja
Respuesta con cualquier tecla:	Ja
Conexiones inalámbricas:	Ja
Contestador automático:	Nee
Colocar llaves:	Handset
Transferencia de llamada explícita:	Ja