Sani-Lav 727A Manual de Usario

Sani-Lav Hundir 727A

Lee a continuación 📖 el manual en español para Sani-Lav 727A (6 páginas) en la categoría Hundir. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/6

A C O R B AT T E R Y P O WERE D

S I N K W I T H E L E C T R O N I C S E N S O R

Operating Manual for Hands-Free Floor Mount Stainless Steel Sink

AC Models 727A and 727A-0.5

Battery Models 727B and 727B-0.5

of Domestic and Foreign Parts

Columbia does not recommend use with harsh chemicals.

Product Compliance

NSF/ANSI 2 Food Equipment, NSF/ANSI 372 Lead-Free Compliant, ASME A112.18.1

A C O R B AT T E R Y P O W E R E D

S I N K W I T H E L E C T R O N I C S E N S O R

COLUMBIA SPECIFICATIONS

800.626.2117 columbiasinks.com info@columbiasinks.com

Installation Instructions

Step 1

1. Attach upper and lower leg support brackets to legs with hardware (provided).

2. Place wash station sink on leg assembly and secure with hardware (provided).

3. Establish sink location.

4. Mark the floor where the four holes are at the base as shown in illustration A.

5. Drill holes as required for mounting hardware. (Hardware not included).

Step 2

1. Install strainer assembly.

2. Install faucets to the sink following the instructions provided with sensor unit.

3. Attach supply tube with elbow to back of faucet.

4. Install mixing check valve and compression fitting to control box of each sensor faucet.

Step 3

1. Secure wash station to floor.

2. Connect waste line to strainer assembly (s).

3. Mount sensor control boxes at desired location on wall.

4. Connect power line from sensor to control box.

5. Attach supply tube from faucet to control box.

6. Connect hot and cold water from the source to mixing check valve (s).

7. Remove aerator from the spout assemblies and flush water system. (see step 7 sensor

installation instructions)

8. Check connections for leaks.

9. Replace aerator onto the spout (s).

Step 4

1. Seal gap between bowl and leg assembly as shown in illustration B.

2. We recommend sealing top of backsplash to wall if applicable as shown in illustration C.

Parts List

(1) Floor mount sink

(1) Leg assembly set

(6) Nuts, bolts and washers for leg assembly

(4) Nuts and washers for connecting sink to leg assembly

(1) AC or Battery powered sensor faucet assembly

(1) Mixing check valve

(1) Strainer assembly with basket

WARNING: This product can expose you to chemicals including Chromium (hexavalent compounds),

Lead, and Phthalates (DEHP) which are known to the State of California to cause cancer and birth defects

or other reproductive harm. For more information go to www.P65Warnings.ca.gov.

NOTE: Lead content originates from Brass components in valves and faucets and is certied under

NSF/ANSI 372 as containing less than 0.25% lead in wetted surfaces.

Notice for California Consumers

Tools Required

Tape measure

Adjustable wrench

Drill motor and drill bits

Pipe wrench

Level

Safety glasses

Screw drivers: phillips and standard

Pencil

Socket wrench

Go to for more information on replacement parts and installation videos. columbiasinks.com

Illustration A

Illustration B

Illustration C

A C O R B AT T E R Y P O W E R E D

S I N K W I T H E L E C T R O N I C S E N S O R

COLUMBIA SPECIFICATIONS

800.626.2117 columbiasinks.com info@columbiasinks.com

10in

254mm

10in

254mm

6.25in

158.8mm

Front Side

Top

Hole Conﬁguration

.875” [22mm]

dia. hole

.5” dia. Floor

Mounting

Holes 7.5”

on Center

1.5” Leg

Thickness

.75” From

Edge of Leg

to First Hole

Floor Mounting Detail

10in

254mm

10in

254mm

9.5in

241.3mm

7in

178.9mm

27in

685.8mm

15.25in

387.4mm

6.25in

158.8mm

20in

508mm

2in

50.8mm

14in

355.6mm

1.5in

38.1mm

17in

431.8mm

17.5in

444.5mm

R.5in

12.7mm

1.5in

38.1mm

2in

50.8mm

3.937in

100mm

45deg

12in

304.8mm

3in

76.2mm

R.75in

19.1mm

.75in

19.1mm

7.5in

190.5mm

2.25in

57.2mm

2.5in

63.5mm

15.5in

393.7mm

11in

279.4mm

Especificaciones del producto

Marca:	Sani-Lav
Categoría:	Hundir
Modelo:	727A
Color del producto:	Zwart
Tecnología de conectividad:	Bedraad
Número de teclas, teclado:	104
Destinado a:	Pc/server
Soporta Windows:	Ja
Número:	1
Temperatura de almacenamiento:	-20 - 65 °C
Iluminar desde el fondo:	Nee
Conexión:	USB
Atajos:	Ja
Teclado numérico:	Ja
El consumo de energía:	250 mA
Incluye ratón:	Nee
Teclas de Windows:	Ja
Teclado de tamaño completo:	Ja
Color de superficie:	Monochromatisch
Diseño del teclado:	QWERTY
Soporte de la muñeca:	Nee
Tamaño del teclado:	Volledige grootte (100%)
Teclado de estilo:	Recht
Temperatura de funcionamiento (TT):	0 - 55 °C
Humedad relativa de funcionamiento (VV):	10 - 95 procent
Lenguaje del teclado:	Engels
Lector de tarjetas magnéticas:	Ja