SEADA G88-HDMI Manual de Usario
SEADA
Procesador
G88-HDMI
Lee a continuación 📖 el manual en español para SEADA G88-HDMI (2 páginas) en la categoría Procesador. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
G Quick Start Manual 88
SD- -014 EN V01
Note
1. Do not fix the device to any surface which is a heat source to avoid over heating
2. Do not cover the surface or ventilation grills of the device to avoid over heating
1. Verify the package contents
Please verify the package contents against the List Below
1. G88 Controller x1
2. Power Cable x1
3. Software Disk x1
4. Serial Cable x1
5. Network Cable x1
6. Remote Contr ol x1
2. Set up the G88
I. Connect the power cable to the unit and power it up
II. Connect the outputs to the screens of the video wall
III. Connect all the video sources to the inputs of the devices
Note: G88 remembers the settings used on the device before power off. The default setting for the new unit is 2x4
video wall with across the 8 screens. All outputs are set at resolution of 1920 x 1080@60. input 1
3. Run the software on control PC
Users can run the G88H.exe software directly without installation. Software is on the disk in the package or you can
download it from the SEADA website. Double click the G88H software to get the Dialog box as below
Default password for Administrator:111111
Default password for User: 000000
Type in the password and log in
4. Connect through Serial Port
Connect the G88 with a serial cable to the control PC (cable included in
the package)
If the software was connected via UART (RS232) last time, software will connect to the G88 automatically vis RS232. If
it was used at Network last time error message will be shown on screen and users need to set up , a ‘Network Timeout’
as below for RS232 connection in the software
• Choose ‘ ’ instead of ‘ ’UART Network
• Select the from the dropdown menu COM port Port
• Press button to connect ‘Disconnected’
5. Connect through Network
The default IP address for G88 controller is Users need to change the IP address of the control PC to 192.168.0.247,
static TCP/IPv4 Ethernet Properties IP address and the same network segment as the G88 at in
IP address: any address between and except the address which has been taken by the 192.168.0.2 192.168.0.254
G88
Subnet mask: Default Gateway: 255.255.255.0, 192.168.0.1
G Quick Start Manual 88
SD- -014 EN V01
Connect the G88 with a CAT cable to the control PC
(cable included in the package)
If the software was connected via Network last time,
software will connect to the G88 automatically via
network. If it was used at serial port Please last time, a ‘
select COM port’ error message will be shown on screen
and users need to set up as below for Network connection in the software
• Choose ‘ ’ instead of ‘ ’Network UART
• Press button to find the G88 on the network ‘Search Device’
• Highlight the device Press button to connect ‘Disconnected’
6. Set up the video wall
Once connected, G88 will load the settings used from last
time. The default setting for the new unit out of package
is 2x4 video wall with input 1 across the 8 screens. All
outputs are set at resolution of 1920 x 1080@60.
Select the and users can set up the video ‘Video Wall’ tab
wall layout in , Bezel correction in ‘VideoWall Setting’
‘Bezel Setting’ and Save/Load preset video wall layouts in
‘Layout Save/Load’
Right click on the video wall, users can use the tools in
‘Dropdown menu’ to set up the video walls.
• Screen Splicing - This combines the selected screens into
one and displays the selected input across all the splicing
screens. For example, in the setup 2x4 at left, if all of them
are spliced, then the input selected by the user will be
displayed across all the 8 screens.
(Users can create more than one video wall on G88. e.g. they
can create two 2x2 video walls instead of one 2x4 video wall
or 3, 4 independent video walls)
• Cancel Splicing –This will cancel the video wall and revert
to the matrix switching mode
• Screen Cancel Splicing – – This will cancel the very screen
and revert only that screen to the matrix switching mode to
form a Picture in Picture effect
• Input Select –This allows the user to control which input is
displayed on video wall
• Output Select –The user can control which screen should
be mapped to which output (only available in matrix mode)
• Output Type –Allows the user to adjust the type of the output (only available in matrix mode)
• Output Format – Controls the resolution of the output (only available in matrix mode)
• Sync lock –to form sync between different screens in the same video wall
This quick start manual provides basic instructions for setting up SEADA G video wall controllers. For additional 88
information about how to use the controllers, please refer to the G User Guide ( - - ), which is available 88 SD EN 015
on the CD included in this package.
Especificaciones del producto
| Marca: | SEADA |
| Categoría: | Procesador |
| Modelo: | G88-HDMI |
¿Necesitas ayuda?
Si necesitas ayuda con SEADA G88-HDMI haz una pregunta a continuación y otros usuarios te responderán
Procesador SEADA Manuales
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
14 Septiembre 2024
Procesador Manuales
- Procesador HP
- Procesador Yamaha
- Procesador Alpine
- Procesador Black And Decker
- Procesador Lenovo
- Procesador Toa
- Procesador Roland
- Procesador Summit Audio
- Procesador LD Systems
- Procesador Bogen
- Procesador Matrox
- Procesador Allen & Heath
- Procesador Bose
- Procesador Fujitsu
- Procesador Rupert Neve Designs
- Procesador Intel
- Procesador Chandler
- Procesador Zoom
- Procesador Eventide
- Procesador Radial Engineering
- Procesador RGBlink
- Procesador DBX
- Procesador Solid State Logic
- Procesador Mathew Lane
- Procesador SPL
- Procesador Drawmer
- Procesador Smart-AVI
- Procesador SIIG
- Procesador Sonifex
- Procesador Manley
- Procesador KanexPro
- Procesador Ashly
- Procesador Dangerous Music
- Procesador Helix
- Procesador TC Helicon
- Procesador Atlas Sound
- Procesador Neutrik
- Procesador AMD
- Procesador CEDAR
- Procesador Lectrosonics
- Procesador Vivolink
- Procesador AudioThing
- Procesador Avenview
- Procesador Phoenix Gold
- Procesador BSS Audio
- Procesador AMX
- Procesador MuxLab
- Procesador FabFilter
- Procesador Metric Halo
- Procesador Datapath
- Procesador Henry Engineering
- Procesador MyMix
Últimos Procesador Manuales
21 Octubre 2024
1 Octubre 2024
27 Septiembre 2024
21 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024
18 Septiembre 2024