Sekonic L-558 Manual de Usario
Sekonic
medidor de luz
L-558
Lee a continuación 📖 el manual en español para Sekonic L-558 (2 páginas) en la categoría medidor de luz. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
Sekonic L-558 / CINE
Quick Guide
LCD Display / Custom Settings Sekonic L-558
To set Custom Settings:
1. Turn power off.
2. Press down Mode key while turning on meter.
3. “CS” (Custom Settings) will appear in upper right hand corner.
4. Use the JOG WHEEL to select Custom Setting number (No.)-see chart below.
5. Press Mode Key to Select Item Number (Item #)-see chart below.
6. Turn meter off and then back on to activate functions.
7. NOTE: L-558 - Pressing M.CLEAR in CS mode will reset all settings to default (No. 0)
L-558 CINE - Same as L-558 except for items 8 & 9 which are set to
selection (No. 3).
Measuring
Modes Incident / Reflected
Spot Function Icons
ISO Display
Analyzed %
of Flash
Indicator
Luminance
Indicator
Exposure
Compensation
Memory/Multi
Flash Indicator
Battery
Indicator
Shutter
Priority
Indicator,
Shutter
Speed &
f.p.s Display
Analog Scale Digital Aperture Value, Aperture Priority, EV
Brightness Difference, Average Function, EV Display
Radio Trigger Mode
#401-970 € D05-03-5
0 1 2 3
1 558 Ambient & Flash ISO 2 Setting Film Sensitivity
1/3 Step
Filter
Compensation (1)
0.1 EV Step
(±5EV)
- -
CINE Film Sensitivity
1/3 Step
Filter
Compensation (1)
0.1 EV Step
(±5EV)
Filter
Compensation
(2) 7 Filter
Factor
Numbers
2 558 & CINE Ambient & Flash Exposure Compensation Display Setting Always Displayed Not Displayed - -
3* 558 & CINE Ambient & Flash Increments of Reading Full Stop 1/3 Stop 1/2 Stop -
4 558 & CINE Ambient Aperture (F) priority mode Available Not Available - -
5 558 & CINE Ambient EV Mode Available Not Available - -
6 558 & CINE Flash Multiple Flash Mode (cumulative) Available Not Available - -
7** CINE Ambient Illuminance or Luminance
(CINE only) Display
Compound +
Individual Compound Individual -
8 CINE Ambient Illuminance Measurement in Incident Mode Not Available LUX FC LUX, FC
9 CINE Ambient Luminance Measurement in Reflected Mode Not Available cd/m2FL cd/m2, FL
* 1/10 stop fractions are displayed in full, 1/2 and 1/3 step increments.
** Individual: LUX, FC, cd/m2, or FL Compound: LUX+T+F, FC+T+F, cd/m2+T+F or FL+T+F (combination)
Custom Setting List
Item
Custom Setting NameLightingNo. Model
Advanced Functions - Sekonic L-558
Motion Picture (CINE)
Turn JOG WHEEL (in T Priority Mode) past shutter speeds
8000, 1/200, 1/400 to select f/s (frames per second). Press
measure button.
Averaging Function
After two or more measurements are memorized, toggle
AVE/ key. Averaged exposure will be displayed in digital
and analog readouts. Operates in all measuring modes.
Brightness Difference Function
Can be used in all modes (incident, reflected, ambient and
flash). Take measurement(s), press the AVE/ button
will display. Press and hold down the Measure button. The
difference between the last memorized reading or averaged
reading and new area measured is displayed in +/- 1/10th
steps of EV.
Flash Analyzing
In all flash modes: Take a flash measurement. A combined
reading of both ambient and flash will be displayed. Turn the
JOG WHEEL to adjust ratio between ambient and flash.
Adjust aperature and shutter as required on camera.
EV Readout - Option 5 in Custom Settings Chart
Select item O (EV) in the CS software settings to turn "ON"
EV mode. Select Ambient Mode. Hold down Mode key and
turn JOG WHEEL until EV readout shows. Press measure
button.
Multi Flash Mode - Option 6 in Custom Settings Chart
Hold down Mode key and turn JOG WHEEL to select Cord,
Cordless or Radio Trigger Mode with MLT shown on display.
Trugger flash repeatedly until target f/stop is achieved.
Exposure Compensation
Hold in both ISO 1 and ISO 2 simultaneously and turn the
JOG WHEEL to exposure compensation needed between
+/- 9.9 EV.
Calibration
Meter must turned off. Tap Power button once while holding
in ISO 1 and ISO 2 keys. CAL will be displayed on panel.
Turn the JOG WHEEL while holding down both ISO keys to
compensate between +/- 1.0 EV.
Quick Guide to the Sekonic L-558 Basic Operation - Sekonic L-558
On/Off
Press down power key to turn on meter. Battery icon will
appear Monitors Battery level. Press and hold Power key
to turn off.
Set ISO 1 or ISO 2
Hold down ISO 1 or ISO 2 while turning the JOG WHEEL.
1° Spot meter mode
Turn SPOT/INCIDENT SELECTOR SWITCH to to select
Spot. Press measure button.
Incident meter mode
Turn SPOT/INCIDENT SELECTOR SWITCH to to select
Incident. Turn Lumisphere retracting ring counter-clockwise
to the full UP right position. Press measure button.
Measure Brightness / Contrast Difference
Turn Lumisphere retracting ring clockwise to lower the
Lumisphere to the DOWN position. Select measuring mode
then press measure button.
Ambient Reading
Select Ambient Mode by holding down the Mode key and
turning the JOG WHEEL. Press the measure button.
Cord Flash Reading
Select Cord Flash Mode. Connect flash cord. Press
measure button,to trigger flash and measure light.
Cordless Flash Reading
Select Cordless Flash mode. Press measure button, trigger
flash manually, meter measures light, automatically resets.
Radio Triggering Mode (with optional RT-32 Module)
Turn power OFF. Remove Connector cover inside battery
compartment. Insert optional RT-32 Module. Turn Power
ON. Hold MODE key in while turning the JOG WHEEL to
RADIO FLASH TRIGGERING MODE, a blinking channel
number will appear. Turn JOG WHEEL to select channel
number. To select Quad-Triggering sub-channels , , , ,
simply press the direct function keys: AVE/ , ISO 1 ,
ISO 2 or M.Clear on the control panel. Pressing the
measure button once returns the screen to the main menu.
Pressing the measure key again simultaneously fires flash
and measures light.
Memory Function
Take measurement, press Memory button. Up to nine
readings can be stored and displayed on the analog memory
scale by repeating the procedure. A tenth measurement can
also be displayed.
RETRACTABLE
LUMISPHERE
RING
1° SPOT
SPOT/INCIDENT
SELECTOR SWITCH
MEMORY
ON/OFF
ISO 2
MODE KEY
Press while turning JOG WHEEL for:
JOG WHEEL
FLASH CORD
SOCKET
MEMORY CLEAR
BUTTON
1/4” TRIPOD
SOCKET
AVERAGE /
BRIGHTNESS
DIFFERENCE
DIOPTER
CORRECTION
RING
MEASURE
BUTTON
AUTO RESET CORDLESS FLASH MODE
DAYLIGHT / AMBIENT MODE
FLASH W/CORD
OPTIONAL PLUG-IN RADIO FLASH TRIGGERING
- - - - - - - - - ->
- - - - - - -
Key Lock and Unlock:
Hold MODE key in. Toggle ISO 1 key to lock or unlock.
“LOc” will display briefly.
ISO 1
bd
c
A
b
cd
A
A b cd
Especificaciones del producto
| Marca: | Sekonic |
| Categoría: | medidor de luz |
| Modelo: | L-558 |
¿Necesitas ayuda?
Si necesitas ayuda con Sekonic L-558 haz una pregunta a continuación y otros usuarios te responderán
medidor de luz Sekonic Manuales
2 Octubre 2024
2 Octubre 2024
3 Septiembre 2024
24 Agosto 2024
16 Agosto 2024
13 Agosto 2024
medidor de luz Manuales
- medidor de luz Pyle
- medidor de luz Extech
- medidor de luz Voltcraft
- medidor de luz Kyoritsu
- medidor de luz Gossen
- medidor de luz Uni-T
Últimos medidor de luz Manuales
2 Octubre 2024
14 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
13 Septiembre 2024
10 Septiembre 2024
11 Agosto 2024
31 Julio 2024
28 Julio 2024
22 Julio 2024