Sharp PN-ZB03H Manual de Usario

Sharp receptor PN-ZB03H

Lee a continuación 📖 el manual en español para Sharp PN-ZB03H (2 páginas) en la categoría receptor. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

PN-ZB03H

Operation Manual HDBaseT Receiver Board

Applicable models

(as of May 2016)

LCD MONITOR

PN-R556/PN-R496/PN-R426

Available models differ according to region.

CAN ICES-3 (A) / NMB-3 (A)

• THANK YOU FOR PURCHASING A SHARP PRODUCT.

Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the

section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be

accessed at any time.

As for how to use the product, refer to the operation manual of the LCD MONITOR.

TIPS

- This product was shipped after strict quality control and inspection; however, if breakage or a malfunction should be found, contact your SHARP dealer

or your nearest customer contact.

- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other

malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

- This product and its accessories may be upgraded without advance notice.

IMPORTANT:

To aid reporting in case of loss or theft, please record the product’s model and

serial numbers in the space provided.

The numbers are located on the product.

Model No.:

Serial No.:

U.S.A. ONLY

WARNING:

FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the manufacturer could void the

user’s authority to operate this equipment.

NOTE:

This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

U.S.A. ONLY

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

U.S.A. ONLY

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take

adequate measures.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: USB terminal, HDBaseT terminal.

To ensure safe and correct use

This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels and incorrectly using the

product could have results as classied below.

Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all instructions.

Warning: Not following these instructions could result in death or serious injury.

•AskyourSHARPdealerorqualiedservicepersonfortheattachment/detachmentofthisproduct.

Attachment/detachment of this product by the customer may result in electric shock or injury.

•Nevertrytomodify,disassemble,orrepairthisproduct.

Doing so may result in re, electric shock, or injury.

•Onlyusetheaccessorieswithspeciedmodels.

Failure to do so may result in re.

CINSE1411MP51 (1)

Supplied accessories

If any component is missing, please contact your dealer.

□ HDBaseT Receiver Board: 1

□ Terminal label: 1

□ Operation manual (this manual)

□ Installation Manual (instructions for SHARP dealers and service

engineers): 1

• HDBaseT is a registered trademark of the HDBaseT Alliance.

• The terms HDMI and HDMI High-Denition Multimedia Interface, and

the HDMI Logo are trademarks or registered trademarks of HDMI

Licensing, LLC in the United States and other countries.



123

1. HDBaseT



Use a commercially available LAN cable (Category 6

or better shielded cable) to connect to an HDBaseT

transmitter.

2. USB



You can connect a USB mouse or keyboard (HID class)

to this terminal to control the computer connected to the

HDBaseT transmitter.*

3. LAN



Use a commercially available LAN cable to connect to

the network. You can use this terminal in place of the

LAN terminal of the monitor.

Do not connect the LAN terminal to the same network

as the LAN that the board is connected to by way of

the HDBaseT terminal. A network loop malfunction will

occur.

You have to use this product with a transmitter that supports the

HDBaseT 2.0 standard. Connections to all transmitters is not guaranteed.



A commercially available HDBaseT transmitter is required to use

this board. Depending on the transmitter, some functions may not be

available. Check with the manufacturer regarding HDBaseT transmitter

specications.



• When you use this device, set the input mode to OPTION.

• In some cases, the power of the HDBaseT receiver board may remain

on even in the standby mode or input signal waiting mode. Power

consumption will be higher when this occurs.

• The power consumption of the monitor with this board attached

increases by up to 12 W.

• To use LAN signals or RS-232C signals via HDBaseT and LAN signals

that have been applied to this board’s LAN terminal, change the

CONTROL ROUTE setting under COMMUNICATION SETTING on the

SETUP menu.

You can also use control commands to change the setting.

Function Direction Reply  

Responsecontents

CONTROL

ROUTE

CTCH 0-1 0-1 0: MONITORWR

1: OPTION

○

“○” indicates a command which cannot be used in standby mode when

POWER SAVE MODE is set to ON.

When CONTROL ROUTE is set to OPTION, the communication speed

is xed to 9600 bps. Also, you cannot set POWER SAVE MODE to ON.

• AUTO INPUT SELECT PRIORITY is not supported.

• You can use the INFORMATION3 screen to check things such as the

communication status of the board as shown below. Set the input mode

to OPTION.

- SIGNAL STRENGTH: This displays the signal strength. The smaller

the value, the stronger the signal. To ensure stable operation, a signal

strength of at least -10 dB (-10 dB, -11 dB, -12 dB, etc.) is necessary.

- LINK STATUS: NO LINK, LINK, LOW POWER, or ETHERNET is

displayed. When LOW POWER is displayed, the link has been

established, but video cannot be transmitted. ETHERNET is displayed

when the cable that should be connected to the LAN terminal is

erroneously connected to the HDBaseT terminal.

- HDMI STATUS: NO HDMI, HDMI, or HDCP is displayed.

NO HDMI: No video data has been received.

HDMI: HDMI/DVI data without HDCP is being received.

HDCP: HDMI/DVI data with HDCP is being received.

*Set the input mode to OPTION before checking the status.

When you connect the HDBaseT Receiver Board, the following become

enabled on the monitor.

• If you are using an Extron device, set EXTRON XTP to ON under

COMMUNICATION SETTING on the SETUP menu.

• The following control commands become enabled.

Function Direction Reply  

Responsecontents

EXTRON

XTP

EXTN WR 0-1 0-1 0: OFF 1: ON ○

“○” indicates a command which cannot be used in standby mode when

POWER SAVE MODE is set to ON.



Model PN-ZB03H

Supported standard HDBaseT 2.0

 HDBaseT terminal

LAN terminal (10BASE-T/100BASE-TX)

USB terminal (USB 2.0 compliant)

Max. resolution (pixels) 4096 x 2160 (30Hz)*



distance

100 m*

Copy protection Supports HDCP (pass through)

 Supplied from the monitor

Input voltage 12 - 19 V

 12 W



 

Approx. 4-15/16(W) x 5-3/8(D) x

1-3/16(H) (124.6 x 136.5 x 30)

  Approx. 0.408(185)

To connect the devices, use a commercially available category 6 or

better shielded cable.

• Use this device within the operating temperature and humidity

conditions of the monitor.

As a part of our policy of continuous improvement, SHARP reserves the

right to make design and specication changes for product improvement

without prior notice. The performance specication gures indicated are

nominal values of production units. There may be some deviations from

these values in individual units.

Printed in China

16G CN1

Especificaciones del producto

Marca:	Sharp
Categoría:	receptor
Modelo:	PN-ZB03H
Número de puertos Ethernet LAN (RJ-45):	9
Certificación:	CE Approval, RoHS
Dimensiones (Ancho x Fondo x Alto):	234 x 138 x 46 mm
voltaje-de-entrada-de-CA:	100-240 V
Frecuencia-de-entrada-de-CA:	50 - 60 Hz