Shop-Vac J200A Manual de Usario

Shop-Vac aspiradora J200A

Lee a continuación 📖 el manual en español para Shop-Vac J200A (9 páginas) en la categoría aspiradora. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/9

ATTENTION!

Read all safety rules careful-

ly before attempting to oper-

ate. Retain for future reference.

Patents Issued and Pending. Printed in U.S.A.

DANGER!

Never operate this unit when

flammable materials or vapors

are present because electrical

devices produce arcs or sparks

that can cause a fire or explo-

sion.

NEVER OPERATE

UNATTENDED!

MSC1896

SHOP-VAC CORPORATION

2323 Reach Road, P.O. Box 3307

Williamsport, PA 17701-0307

(570) 326-3557

Web site: www.shopvac.com

SHOP-VAC CANADA

1770 Appleby Line

Burlington, Ontario L7L 5P8

(905) 335-9730

Web site: www.shopvac.ca

Shop Vac-México, S.A. de C.V.

Calle Niños Héros #1553

Colonia Agua Blanca

45235 - Zapopan, Jalisco

52 (33) 3188 6388

127(7KLVLVDJHQHULFPDQXDO,WHPVVKRZQPD\QRWDSSO\WR\RXUYDFXXP

3OHDVHFRQWDFWFXVWRPHUVHUYLFHZLWKTXHVWLRQV

WARNING!

Do NOT use this vacuum cleaner

to vacuum lead paint debris

because this may disperse fine

lead particles into the air. This

vacuum cleaner is not intended

for use under EPA Regulation

40 CFR Part 745 for lead paint

material cleanup.

When using an electrical appliance, basic precautions should always be followed, including the

following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC

SHOCK OR INJURY:

1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before

servicing. Connect to a properly grounded outlet only. See Grounding Instructions.

2. Do not expose to rain – store indoors.

3. Do not allow to be used as a toy. Close attention is necessary when used by or near children.

4. Use only as described in this manual. Use only Manufacturer’s recommended attachments.

5. Do not use with damaged cord or plug. If appliance is not working as it should, has been

dropped, damaged, left outdoors or dropped into water, contact Shop-Vac Corporation for

assistance.

6. Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around

sharp edges or corners. Do not run appliance over cord. Keep cord away from heated sur-

faces.

7. Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.

8. Do not handle plug or appliance with wet hands.

9. Do not put any object into openings. Do not use with any openings blocked; keep free of dust,

lint, hair and anything that may reduce air flow.

10. Keep hair, loose clothing, fingers and all parts of body away from openings and moving parts.

11. Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.

12. Do not use without dust bag and/or filters in place.

13. Turn off all controls before unplugging.

14. Use extra care when cleaning on stairs.

15. Do not use to pick up flammable or combustible liquids such as gasoline or use in areas

where they may be present.

16. Do not use your cleaner as a sprayer of flammable liquids such as oil base paints, lacquers,

household cleaners, etc.

17. Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as

asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials.

Specially designed units are available for these purposes.

18. Do not pick up soot, cement, plaster or drywall dust without cartridge filter and collection filter

bag in place. These are very fine particles that may pass through the foam and affect the

performance of the motor or be exhausted back into the air. Additional collection filter bags

are available.

19. Do not leave the cord lying on the floor once you have finished the cleaning job. It can become

a tripping hazard.

20. Use special care when emptying heavily loaded tanks.

21. To avoid spontaneous combustion, empty tank after each use.

22. The operation of a utility vac can result in foreign objects being blown into eyes, which can

result in eye damage. Always wear safety goggles when operating vacuum.

23. STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum

cleaner when you are tired, distracted or under the influence of drugs, alcohol or medication

causing diminished control.

24. WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this

may disperse fine lead particles into the air. This vacuum cleaner is not intended for use

under EPA Regulation 40 CFR Part 745 for lead paint material cleanup.

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

When using the appliance at a distance where an extension cord becomes necessary, a 3-con-

ductor grounding cord of adequate size must be used for safety, and to prevent loss of power and

overheating. Use the table below to determine A.W.G. wire size required. To determine ampere

rating of your vacuum, refer to nameplate located on rear of motor cover.

EXTENSION CORDS

the plug illustrated in sketch A. A

temporary adapter that looks like

the adapter illustrated in sketches

B and C may be used to connect

this plug to a 2-pole receptacle

as shown in sketch B if a properly

grounded outlet is not available.

The temporary adapter should be

used only until a properly grounded

outlet (sketch A) can be installed

by a qualified electrician. The

green colored rigid ear, lug or the

like extending from the adapter must be connected to a permanent ground such as a properly

grounded outlet box cover. Whenever the adapter is used, it must be held in place by a metal

screw.

IN CANADA, THE USE OF A TEMPORARY ADAPTER IS NOT PERMITTED BY THE

CANADIAN ELECTRICAL CODE. Make sure that the appliance is connected to an outlet having

the same configuration as the plug. No adapter should be used with this appliance.

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a

path of least resistance for electric current to reduce the risk of electric shock. This appliance is

equipped with a cord having an equipment-grounding conductor and grounding plug. The plug

must be inserted into an appropriate outlet that is properly installed and grounded in accordance

with all local codes and ordinances.

WARNING – IMPROPER CONNECTION OF THE EQUIPMENT-

GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC

SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE

PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS

PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED

WITH THE APPLIANCE – IF IT WILL NOT FIT THE OUTLET, HAVE A

PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN.

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like

GROUNDING INSTRUCTIONS

1. Remove vacuum cleaner and all accessories from the carton.

2. Important: Open tank cover by pushing latches or clamps outward with thumbs and remove

any accessories that may have been shipped in the tank.

3. Assemble dolly or caster system following instructions.

UNPACKING

4. Before replacing cover, please refer to Dry Pick up or Wet Pick up operation to ensure proper

filter installation.

5. Replace cover and make sure latches or clamps are secured over raised area of tank cover.

I=ON, O=OFF



WARNING– DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING. UNPLUG UNIT WHEN NOT IN USE.

Before using appliance, inspect power cord for loose or exposed wires and damaged insulation.

Make any needed repairs or replacements before using your appliance. Use only three-wire out-

door extension cords which have three-prong grounding-type plugs and three-pole receptacles

which accept the extension cord’s plug. When vacuuming liquids, be sure the extension cord

connection does not come in contact with the liquid.

NOTE: STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMID-

ITY OF THE AIR IS LOW. THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE

OF THE APPLIANCE. TO REDUCE THE FREQUENCY OF STATIC SHOCKS IN YOUR HOME,

THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR WITH A CONSOLE OR INSTALLED

HUMIDIFIER.

Volts Total length of cord in feet

120V

Ampere Rating

More Not More

Than Than

0 - 6

6 - 10

10 - 12

12 - 16

25 50 100 150

AWG

Not recommended

ASSEMBLY



TOP HANDLE ASSEMBLY

(Not standard with all models)

To attach top handle, align holes in handle and holes in tank cover and secure

with screws provided (Figure 1).

TOOL HOLDER ASSEMBLY

(Not standard with all models)

1. With rear of unit facing you, take tool holder and position it with tabs facing rear

of unit (Figure 2).

2. Place “J” shaped tabs into the slots on cord wraps (Figure3).

3. Press down until tabs snap into place.

4. Press down on center of tool holder until tab latches on bottom of lid (Figure 4).

1RW DOO XQLWV DUH HTXLSSHG ZLWK WKH VDPH FDVWHU V\VWHP )ROORZ WKH

LQVWUXFWLRQVZKLFKDSSO\WR\RXUVSHFLILFXQLW

Without Caster Feet

You will find four casters with your wet/dry vacuum. Assemble as follows:(Figure 5)

1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so

that bottom is facing up.

2. Insert casters into bottom of tank by placing stem of caster

into holes provided. Apply pressure and twisting motion

until casters snap into place (Figure 6).

3. Return tank to upright position.

CASTER SYSTEM ASSEMBLY

10 U.S. Gallons (37.8L) and Up With Caster Feet

You will find four caster feet, four casters and four screws with your wet/dry vacuum. (Figure 16)

Assemble as follows:

1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so

that bottom is facing up.

2. With front of tank facing you, take caster feet marked with the letter A (Figure 17) and place

in slots on left front and right rear of tank also marked with the letter A (Figure 18). Secure

with screws provided (Figure 19).

3. Take caster feet marked with the letter B (Figure 20) and place in slots on right front and left

rear of tank also marked with the letter B . Secure with screws provided (Figure 21) (Figure

22).

4. If flat washers are included in hardware package place flat washer over stem of caster before

installing casters into feet. NOTE: Flat washers are not required with all units.

5-8 U.S. Gallons (18.9 - 30.2L) With Caster Feet

You will find four caster feet , four casters (Figure 7) (Figure 8), and four screws with your wet/

dry vacuum. Assemble as follows:

1. With cord disconnected from receptacle and tank cover removed, turn tank

upside down so that bottom is facing up.

2. Remove any webbing that attaches the caster feet to each other.

3. With front of tank inlet facing you, take caster feet marked with the letter A

(Figure 9) and insert stem of caster foot into holes on left front and right rear

of tank also marked with letter A (Figure 10). Make sure caster feet are fully

inserted into tank bottom and secure with screws provided (Figure 11).

4. Take caster feet marked with the letter B and insert stem of (Figure 12)

caster foot into holes on right front and left rear of tank also marked with

the letter B (Figure 13). Make sure caster feet are fully inserted into tank

bottom and secure with screws provided (Figure 14).

5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and

twisting motion until casters snap into place (Figure 15).

6. Return tank to upright position.

With Rear Caster Dolly/Tool Holder

You will find four casters , two caster feet , rear caster dolly/tool holder (Figure 24) (Figure 25)

(Figure 26), and four screws with your wet/dry vacuum. Assemble as follows:

1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so

that the bottom is facing up.

2. Take rear caster dolly and place into slots (on rear of tank, opposite of drain) and secure with

screws provided (Figure 27).

3. If flat washers are included in hardware package place flat washer over stem of caster before

installing casters into feet. NOTE : Flat washers are not required with all units.

4. Insert casters into bottom of rear caster dolly by placing stem of caster into holes provided.

Apply pressure and twisting motion until casters snap into place (Figure 28).

5. With tank drain facing you, take caster foot marked with the letter A (Figure 29) and place

in slot on left side of tank also marked with the letter A. Secure with screw provided (Figure

30).

6. Take caster foot marked with the letter B (Figure 31) and place in slot on right side of tank

also marked with the letter B. Secure with screw provided (Figure 32).

7. Insert casters into feet by placing stem of casters into holes provided. Apply pressure and

twisting motion until casters snap into place (Figure 33).

8. Return tank to upright position.

9. Place tool basket (not standard with all models) with curved surface against tank on rear

caster dolly assembly (Figure 34).

5. Insert casters into feet by placing stem of caster into holes provided. Apply pressure and

twisting motion until casters snap into place (Figure 23). Return tank to upright position.

REAR CASTER ACCESSORY CADDY AND

FRONT CASTER FEET ASSEMBLY

(Not standard with all models)

You will find four casters, two caster feet, an accessory caddy and four screws

with your wet/dry vacuum.

If your accessory caddy looks like the one pictured in assemble as (Figure 35)

follows.

1. With cord disconnected from receptacle and tank cover removed, turn tank

upside down so that the bottom is facing up.

2. Insert two caster feet into adjacent slots at front of tank. Secure with screws

provided.

3. Take accessory caddy and place into remaining slots at back of tank. Secure

with screws provided .(Figure 36)

4. Install casters into caddy and feet by inserting the caster stems into the holes

provided. Apply pressure and twisting motion until casters snap into place.

If your accessory caddy looks like the one pictured in assembly as follows.(Figure 37)

1. With cord disconnected from receptacle and tank cover removed, turn tank upside down so

that the bottom is facing up.

2. Take accessory caddy and place into slots (on rear of tank opposite of drain). Secure with

screws provided . (Figure 38)

3. With tank drain facing you, take caster foot marked with the letter A (Figure 39) and place

in slot on left side of tank also marked with the letter A. Secure with screw provided (Figure

40).

4. Take caster foot marked with the letter B (Figure 41) and place in slot on right side of tank

also marked with the letter B. Secure with screw provided .(Figure 42)

Especificaciones del producto

Marca:	Shop-Vac
Categoría:	aspiradora
Modelo:	J200A
Color del producto:	Zwart
Ancho:	450 mm
Profundidad:	39 mm
Altura:	425 mm
Ancho del embalaje:	63 mm
Empaquetadura en profundidad:	50 mm
Altura del embalaje:	550 mm
Método de montaje:	Muur
País de origen:	China
Capacidad máxima de peso:	40 kg
Interfaz de montaje en panel:	50 x 50,75 x 75,75 x 100,75 x 200,100 x 100,100 x 150,100 x 200,100 x 75,120 x 120,200 x 100,200 x 200,200 x 300,200 x 400,300 x 100,300 x 200,300 x 300,350 x 350,400 x 200,400 x 400,400 x 300 mm
Caja de cartón de peso neto:	15000 g
Peso neto del paquete:	1300 g
Compatibilidad de la interfaz de montaje (min):	50 x 50 mm
Compatibilidad de la interfaz de montaje (máx.):	400 x 400 mm
Número de pantallas admitidas:	1
Gestión de cables mejorada:	Nee
Altura del paquete principal (exterior):	570 mm
Ancho del embalaje principal (exterior):	267 mm
Longitud del paquete principal (exterior):	210 mm
Cantidad por caja principal (exterior):	15 stuk(s)
Tamaño máximo de pantalla:	65 "
Código del Sistema Armonizado (SA):	7326909890
Productos por palet (UE):	630 stuk(s)
Tamaño mínimo de pantalla:	32 "
Distancia a la pared (máx.):	39 mm
Período de garantía:	5 jaar
Adecuado para candado:	Ja
Adecuado para televisión:	Ja