SIIG CE-MT0612-S1 Manual de Usario
SIIG
soporte de panel plano
CE-MT0612-S1
Lee a continuación 📖 el manual en español para SIIG CE-MT0612-S1 (8 páginas) en la categoría soporte de panel plano. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/8
04-0528A
Low Profile Universal Mount - 32" to 60"
IMPORTANT: If you don't understand the installation instructions, please consult an installation
specialist
Fixed LCD/TFT TV Wall Mount
Material: 2.0mm Cold Rolled Steel Plate
TV Size: 32-60"
Max load capacity:165 lbs/75 kgs
Installation Instructions
Wall distance: 30mm/1.2"
Bubble level system included
Universal Mounting Pattern
A G
B H
C I
D J
E K
F L
M
(×4) M8 concrete anchor
(×4) M4×35 screw (×6) M8 Washer
(×4) M8 Spacer
(×4) M8×35 screw
The wall structure must be capable of supporting at least the maximum load capacity as indicated. If not, the wall must be
reinforced. Proper installation procedure by yourself or a qualified service technician, as outlined in the installation
instructions, must be adhered to. Failure to do so could result in serious personal injury.
Do not install near heater, fireplace, air conditioning, in direct sunlight, or any other heat producing source. Failure to do so
may result in damage to the display and could increase the risk of fire.
(×4) M4×12 screw
When mounting to a wall that contains wood studs, confirm dead center of the wood stud prior to installation, it is
recommended that the wood studs be a minimum of 16" apart.
(×4) M6×16 screw (×6) Bolt
(×4) M8×16 screw
INSTALLATION AND OPERATING INSTRUCTIONS
(×4) M6×35 screw
Caution
Hardware kit:
It is recommended that two people perform the installation. Injury and/or damage can result from dropping or mishandling
the display.
CAUTION: The maximum load capacity is 165 lbs. Use with products exceeding the maximum load capacity may cause
serious injury. See apparatus instructions.
(×4) M8/M6/M5 Washer
(×4) M4×16 screw
(×4) M5×16 screw
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result in
damage to the display and/or damage to the mounting surface.
Recommended mounting surfaces: wood stud and solid-flat concrete. If the mount is to be installed on any surface other
than wood studs, use suitable hardware (not included but commercially available).
Prior to the installation of this product, the installation instructions should be read and completely understood. The
installation instructions must be read to prevent personal injury and property damage. Keep these installation instructions
in an easily accessible location for future reference.
1
2
3
4
a) Wood Stud Installation
3
4
5
6
7
8
Stud finder for drywall installation
5/16" Socket and Wrench
Electric drill and 5/16" (8mm) masonry bit for concrete/brick installation
Note: Please ensure that the bubble level is mounted on the wall plate prior to mounting the wall plate.
Phillips head screw driver
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive torque.
Mark the right (upper and lower) and the left (upper and lower) positions
of the small horizontalslots that are in alignment with the studs (figure 1
-
b).
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.
Tools Required:
You should mark four positions total.
With the help of an assistant, and using the bubble level to ensure the
wall plate is level, position the wall plate against the wall in the desired
mounting location.
2
1
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.
Step1: Wall Plate Installation
Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level to verify
that the wall plate is level.
For each location, insert a lag bolt (J) and washer (L) into the wall
Tighten the bolt with an open ended socket wrench by turning clockwise until tight.
Use a high-quality electronic stud finder (commercially available) to
locate dead center of two studs and mark their locations with a pencil
(figure 1-a).
Next, pre-drill a 1/4" hole to a depth of 2" in the wall stud at each
marked location.
Especificaciones del producto
Marca: | SIIG |
Categoría: | soporte de panel plano |
Modelo: | CE-MT0612-S1 |
¿Necesitas ayuda?
Si necesitas ayuda con SIIG CE-MT0612-S1 haz una pregunta a continuación y otros usuarios te responderán
soporte de panel plano SIIG Manuales
13 Septiembre 2024
soporte de panel plano Manuales
- soporte de panel plano Samsung
- soporte de panel plano HP
- soporte de panel plano Abus
- soporte de panel plano Acco
- soporte de panel plano Hitachi
- soporte de panel plano SilverStone
- soporte de panel plano 3M
- soporte de panel plano GPX
- soporte de panel plano Manhattan
- soporte de panel plano Vision
- soporte de panel plano Kensington
- soporte de panel plano Nec
- soporte de panel plano BlueBuilt
- soporte de panel plano Da-Lite
- soporte de panel plano Luxor
- soporte de panel plano Steren
- soporte de panel plano Digitus
- soporte de panel plano Insignia
- soporte de panel plano Sanus
- soporte de panel plano Peerless-AV
- soporte de panel plano Vogels
- soporte de panel plano Fellowes
- soporte de panel plano Sven
- soporte de panel plano Valueline
- soporte de panel plano One For All
- soporte de panel plano Ematic
- soporte de panel plano Newstar
- soporte de panel plano Ewent
- soporte de panel plano BakkerElkhuizen
- soporte de panel plano Ultimate
- soporte de panel plano Peerless
- soporte de panel plano Proaim
- soporte de panel plano Monoprice
- soporte de panel plano Chief
- soporte de panel plano Ergotron
- soporte de panel plano Gabor
- soporte de panel plano Atdec
- soporte de panel plano StarTech.com
- soporte de panel plano Bell'O
- soporte de panel plano B-tech
- soporte de panel plano Speaka
- soporte de panel plano Crimson
- soporte de panel plano Kogan
- soporte de panel plano Schwaiger
- soporte de panel plano Cabstone
- soporte de panel plano V7
- soporte de panel plano Bretford
- soporte de panel plano SmartMetals
- soporte de panel plano Unicol
- soporte de panel plano Zaor
- soporte de panel plano Dataflex
- soporte de panel plano Multibrackets
- soporte de panel plano Anthro
- soporte de panel plano AMX
- soporte de panel plano Rocstor
- soporte de panel plano CTA Digital
- soporte de panel plano Amer
- soporte de panel plano Avteq
- soporte de panel plano Walker Edison
- soporte de panel plano My Wall
- soporte de panel plano Mount-It!
- soporte de panel plano LTN Technologies
- soporte de panel plano Heckler
- soporte de panel plano Helder
Últimos soporte de panel plano Manuales
27 Octubre 2024
15 Octubre 2024
15 Octubre 2024
4 Octubre 2024
2 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024
1 Octubre 2024