SKS 10078 Manual de Usario

SKS Accesorio para bicicleta 10078

Lee a continuación 📖 el manual en español para SKS 10078 (1 páginas) en la categoría Accesorio para bicicleta. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/1

MADE IN GERMANY SKS-GERMANY.COM

G E R M A N Y

MOUNTING INSTRUCTION ROWDY SET ¬ 10078

EN. ROWDY SET

ROWDY provides maximum splash protection for youth and mountain bikes with a tire size of 20-24 inches. It can be mounted quickly and easily and is

suitable for most frame geometries with and without suspension.

MOUNTING REAR

1. Loosen the screw and remove the adapter and bracket together from the wheel guard.A B C

2.Loosen the two screws in the bracket and remove the adapter B. comes with two adapters ( + ) for mounting on the seat post and the C ROWDY B1 B2

seat tube. Select the right adapter for your seat post:

- adapter B1 for ø 25-32 mm

- adapter B2 for ø 32-37 mm

(The adapters are marked accordingly on the edge)

3. Put the appropriate adapter and bracket around the seat post or the seat tube of the frame. Reapply the screws and tighten slightly. Adjust the height

of the adapter and the bracket and tighten the screws.

4. Now screw the wheel guard back onto the bracket .C

5. If the wheel guard is too long for the frame it can be shortened by cutting as marked with a sturdy pair of scissors.

6. With the screws A and D, can be optimally adapted to the geometry of your bike. The distance to the tire has to be sufﬁcient.ROWDY

MOUNTING FRONT

7. Bike without a suspension fork. Attach the two mounting brackets E onto the fork as shown using the screw, washer and nut and tighten the screw. Now

push the two wheel guards all the way onto the mounting bracket (the brackets may need to be bent into position).

8. + Bike with suspension fork. The mounting position depends on the geometry of the suspension forkand frame. Select a mounting position that a b

suits your bike and mount the wheel guard with the two mounting brackets according to the illustrations , (the brackets may need to be bent into 8a b

position).

SAFETY NOTE

After mounting, check again that all screws are tightened and the wheel guards are at an adequate distance from the tire. The distance should be suf-

ﬁcient along the entire tire (where applicable, check in the deﬂected state). Check that the wheel guards are properly mounted before every ride. If the

distance of the wheel guard to the tire is not sufﬁcient, this can cause damage to the wheel guard or a fall. Make sure that the brakes and suspension are

able to function properly and that the edge protectors do come into contact with the moving parts of the brake or suspension. If the front wheel guard

is to be removed, the metal bracket should also be dismounted.

ROADALLROAD MOUNTAIN

Mind the minimum

distance between tyre

at full spring travel!

ATTENTION

MAX.Ø

SATTELSTÜTZE

SEATPOST

35 mm

FRONTREAR/FRONT

REAR

WITH SUSPENSION FORK (1st OPTION)

WITH SUSPENSION FORK (2st OPTION)WITHOUT SUSPENSION FORK

Especificaciones del producto

Marca:	SKS
Categoría:	Accesorio para bicicleta
Modelo:	10078
Certificación.:	FCC Class A, CE Class A & CISPR Class A
Tecnología de conectividad.:	Alámbrico
Intervalo de temperatura operativa:	0 - 70 °C
Dimensiones (Ancho x Profundidad x Altura):	122 x 85 x 20 mm
Requisitos de energía:	9V/1A
Rango máximo de transferencia de datos:	100 Mbit/s
Bidireccional completo (Full duplex):	Si
Puertos de entrada y salida (E/S):	1 x RJ-45 MDI & 1 x MDI-X\n1 x SC
Longitud de onda.:	1300 nm