Smeg KE61EBE Manual de Usario

Lee a continuación 📖 el manual en español para Smeg KE61EBE (6 páginas) en la categoría campana extractora. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/6
EN 10
RECOMMENDATIONS AND SUGGESTIONS
The Instructions for Use apply to several versions of this appliance. Accordingly, you may find
descriptions of individual features that do not apply to your specific appliance.
INSTALLATION
The manufacturer will not be held liable for any damages resulting from incorrect or improper
installation.
The minimum safety distance between the cooker top and the extractor hood is 650 mm (some
models can be installed at a lower height, please refer to the paragraphs on working dimensions
and installation).
Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of
the hood.
For Class I appliances, check that the domestic power supply guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum diameter 120 mm. The route
of the flue must be as short as possible.
Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces,
etc.).
If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a
sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of
exhaust gas. The kitchen must have an opening communicating directly with the open air in order
to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances
supplied with energy other than electric, the negative pressure in the room must not exceed 0,04
mbar to prevent fumes being drawn back into the room by the cooker hood.
In the event of damage to the power cable, it must be replaced by the manufacturer or by the
technical service department, in order to prevent any risks.
If the instructions for installation for the gas hob specify a greater distance specified above, this has
to be taken into account. Regulations concerning the discharge of air have to be fulfilled.
USE
The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
Never use the hood for purposes other than for which it has been designed.
Never leave high naked flames under the hood when it is in operation.
Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not
engulf the sides.
Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.
Do not flambè under the range hood; risk of fire
This appliance is not intended for use by persons (including children) with reduced physical, sen-
sory or mental capabilities, or lack of experience and knowledge, unless they have been given su-
pervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
CAUTION: Accessible parts may become hot when used with cooking appliances..
MAINTENANCE
Switch off or unplug the appliance from the mains supply before carrying out any maintenance
work.
Clean and/or replace the Filters after the specified time period (Fire hazard).
Clean the hood using a damp cloth and a neutral liquid detergent.
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative
consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information
about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product .
EN 11
CHARACTERISTICS - INSTALLATION
FIXING OF THE HOOD UNDER THE CABINET
To drill the cabinet follow the indications given in the dimen-
sional drawing in the chapter which regards hood dimensions.
To fix the hood onto the cabinet use the 44,4 mm long screws
inserting and tightening them from the inside of the cabinet.
Connection to air outlet
AIR OUTLET IN THE DUCTING MODE
When installing the hood in ducting version, basing on the in-
staller’s choice, a rigid or a flexible pipe is used in order to con-
nect the hood to the air outlet piping.
Insert the flange on the hood body outlet.
Open the metal grid and make sure that the conversion knob is
in the ducting position.
Connect the hood to the air outlet piping with a pipe.
Fix the pipe with an adequate quantity of pipe clamps. This
material is not supplied together with the hood.
Remove the charcoal filter if present.
EN 12
AIR OUTLET IN THE RECYCLING MODE
Open the metal grid and make sure that the conver-
sion knob is in the recycling position.
Place the charcoal filter. The charcoal filter is not
supplied together with the hood. (Hoods with two
motors needs to be equipped with two charcoal fil-
ters).
INSTRUCTIONS ON OPENING THE SUCTION GRILL
Slide the side stops towards the centre of the hood
and at the same time pull the grill forwards.
The grill will drop down, turning on the two rear
pins, and will remain hanging from them.
To disconnect it completely, pull the right hand part
of the grill forwards slightly so that the pin comes out
of the grill through the slot formed on the body of the
hood.
ELECTRICAL CONNECTION
Connect the hood to the mains through a two-pole switch having a contact gap of at least 3
mm..

Especificaciones del producto

Marca: Smeg
Categoría: campana extractora
Modelo: KE61EBE

¿Necesitas ayuda?

Si necesitas ayuda con Smeg KE61EBE haz una pregunta a continuación y otros usuarios te responderán




campana extractora Smeg Manuales

campana extractora Manuales

Últimos campana extractora Manuales