Sonic Alert DB100 Manual de Usario
Sonic Alert
Seguridad
DB100
Lee a continuación 📖 el manual en español para Sonic Alert DB100 (2 páginas) en la categoría Seguridad. Esta guía fue útil para 9 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
WIRELESS DOORBELL SIGNALER
MODEL DB100
SONIC ALERT’S 5 YEAR LIMITED WARRANTY
The Wireless Doorbell Signaler Model DB100 is
warranted against manufacturing defects in materials and
workmanship for five (5) years from the date of purchase.
Within this period Sonic Alert will replace at our option the
DB100 without charge for parts and labor. Simply send
the DB100 (postpaid) and a copy of your sales slip as
proof of purchase to:
Sonic Alert Inc., 1050 E. Maple Road, Troy MI 48083
Operation
The state-of-the-art Doorbell Signaler will alert you when
someone comes to visit. The DB100 is the only doorbell
signaler that does not require wires and can be installed in
seconds. DB100 signaler will alert you that someone is at your
door by flashing a light plugged into it and any other Sonic
Alert remote receivers you may have. The DB100 is designed
to work in homes with or without an existing doorbell or
chime. Selecting Flash Rate
Other features include a selectable number of flashes (5 or 10),
and different flash code for front door, rear door, or intercom.
Additional sensors (DB100T - sold separately) can be used for
2nd door. There is also a built-in chime for hearing members of
the family. The DB100 receives an RF (radio) signal from the
DB sensor, and flashes the light plugged into the built-in outlet
of the signaler. Use a 300-watt or less incandescent lamp only.
The signaler can send a signal to all Sonic Alert remote
receivers. Note: Must be used only with Sonic Alert
receivers for proper operation. Other manufacturers’
products are not reliable with our products.
DB100 Signaler DB Sensor
INSTALLATION
To install the DB100, follow the diagrams and instructions on the
following page that match the type of installation you need for
your home. If the installation follows diagram 1, a 12-volt
alkaline battery is required in the DB sensor.
Please check the switches on your DB Sensor before installing.
Do not change switches 1-6. These are pre set.
Setting the Dip Switches:
DB Sensor settings (smaller unit) for dip switches 1 thru 6 are set
at the factory and only need to be changed if your neighbor has a
DB100 or DB200. The 8 dip switches should be set as follows:
a) 1 thru 3 dip switches are set in the ON position and 4 thru 6
are set in the OFF position. If you need to change the dip switch
settings to avoid interference with your neighbors, make sure you
change the DB100 Signaler to match the DB Sensor.
b) The 7th switch is for when you are using 2 sensors; this switch
determines the settings for front or back door. If using for one
door only set this switch in the ON position. At this setting your
unit will flash at a fast rate and will make a ding/dong sound. If
using 2 sensors, one for the front door and one for the back door,
the setting for the 2nd sensor would be in the OFF position. In this
position the front door will flash at a different flash rate than the
back door. In the OFF position your back door sensor will flash
at a slow rate with a ding/dong sound.
c) The 8th switch determines the number of flashes when
someone is at your door. In the ON position your unit will flash 5
times and in the OFF position your unit will flash 10 times. This
feature is wonderful when you have an extra sensor for the back
door. One sensor would be set in the ON position and the other
would be set in the OFF position.
ON
OFF
1 2 3 4 5 6 7 8
Setting the Audio Switch:
Top - OFF
Bottom - ON
Located on the DB100 Signaler (larger unit):
The speaker switch allows you to turn the Audio Alarm ON or
OFF. ON is down and OFF is up.
Multi-Function Input Jack:
Located on the right side of the DB Sensor, this input jack is
for installations as shown below in diagram 2 & 3.
DB100 INSTALLATION DIAGRAMS
Battery free installation (diagram 3):
Use wire provided, plug into jack outlet on side of
Transmitter. Remove chime cover and connect the red
and yellow wires to chime box terminal screws common
and front.
Troubleshooting & Help:
If you’ve followed the directions and are still having problems
please try the following suggestions:
1) Check battery in the sensor. Must be a 12-volt alkaline type.
2) Check dip switch settings. Both the sensor and the signaler
must match as shown in figure 1.1 above.
3) Check outlet for power.
4) Move the Signaler to an outlet closer to the sensor unit.
5) If using the Multi-Function input jack make sure that the wires
are not touching each other. See diagram number 2 & 3 for
proper installation.
6) Check that sensor is not further than 50 feet from the receiver.
7) Do not place sensor on steel doors or steel door frames.
For Technical help call 1-248-577-5400
M-F 8:00 a.m. – 5:00 p.m. Eastern Time
Or e-mail us with your questions at sonic-info@sonicalert.com
Warranty:
Thank you for purchasing this high quality Sonic Alert product. We hope you
will have many years of satisfied use. This Sonic Alert product comes with a
limited 5-year warranty so please retain your receipt in a safe place for possible
future reference; you will need in the event of warranty service.
Sonic Alert, Inc.
1050 East Maple Rd.
Troy, MI 48083
V/TTY 1-248-577-5400 fax 248-577-5433
E-mail: sonic-info@sonicalert.com
Web Site: www.SonicAlert.com
REV 1.5 (2008)
This device complies with Part 15 of the FCC Rules and with RSS-210
of Industry Canada. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
WARNING: Changes or modifications not expressively
approved by the party responsible for compliance could void
user’s authority to operate the equipment.
Especificaciones del producto
Marca: | Sonic Alert |
Categoría: | Seguridad |
Modelo: | DB100 |
¿Necesitas ayuda?
Si necesitas ayuda con Sonic Alert DB100 haz una pregunta a continuación y otros usuarios te responderán
Seguridad Sonic Alert Manuales
4 Septiembre 2024
3 Septiembre 2024
30 Agosto 2024
23 Agosto 2024
19 Agosto 2024
18 Agosto 2024
12 Agosto 2024
Seguridad Manuales
- Seguridad Bosch
- Seguridad Panasonic
- Seguridad Grundig
- Seguridad Honeywell
- Seguridad Siemens
- Seguridad Abus
- Seguridad Alphatronics
- Seguridad Aritech
- Seguridad Airbolt
- Seguridad Brennenstuhl
- Seguridad Hikvision
- Seguridad Nedis
- Seguridad Eminent
- Seguridad Ezviz
- Seguridad Elro
- Seguridad Axis
- Seguridad Theben
- Seguridad Profile
- Seguridad Trebs
- Seguridad Fenton
- Seguridad Eufy
- Seguridad Steinel
- Seguridad Somfy
- Seguridad Lamax
- Seguridad Netgear
- Seguridad Grothe
- Seguridad LevelOne
- Seguridad Unitron
- Seguridad Netatmo
- Seguridad Bticino
- Seguridad Topcraft
- Seguridad First Alert
- Seguridad Dahua
- Seguridad Foscam
- Seguridad BRK
- Seguridad Hagenuk
- Seguridad Technaxx
- Seguridad Niko
- Seguridad Gira
- Seguridad Jung
- Seguridad Wanscam
- Seguridad Geemarc
- Seguridad Dymond
- Seguridad Friedland
- Seguridad Golmar
- Seguridad Storage Options
- Seguridad Provision ISR
- Seguridad NetworX
- Seguridad Bitron Video
- Seguridad Monacor
- Seguridad Zmodo
- Seguridad Velbus
- Seguridad Electronics Line
- Seguridad HUMANTECHNIK
- Seguridad Directed Electronics
- Seguridad Oplink
- Seguridad Jablotron
- Seguridad Muller
- Seguridad Home8
- Seguridad AVTech - Velleman
- Seguridad Galaxy
- Seguridad Smartalarm
- Seguridad GE Security
- Seguridad Nor-tec
- Seguridad Entrya
- Seguridad Tegui
- Seguridad Iiquu
- Seguridad Woonveilig
- Seguridad Mikros
- Seguridad FlinQ
- Seguridad Myfox
- Seguridad Bellman
- Seguridad Protector
- Seguridad Ksenia
- Seguridad Mr Safe
- Seguridad Fracarro
Últimos Seguridad Manuales
24 Octubre 2024
22 Octubre 2024
21 Octubre 2024
20 Octubre 2024
20 Octubre 2024
18 Octubre 2024
18 Octubre 2024
18 Octubre 2024
5 Octubre 2024