Speco Technologies AP200M Manual de Usario

Speco Technologies repetidor wifi AP200M

Lee a continuación 📖 el manual en español para Speco Technologies AP200M (4 páginas) en la categoría repetidor wifi. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/4
A
AP
P2
20
00
0M
M/
/A
AP
P3
30
00
0M
M 300Mbps, Outdoor Network Video Bridge w/DIP
function
Thank you for your choice of Speco Technologies’ point-to-point AP. These units are designed AP200M or AP300M
and manufactured to provide an efficient way to connect from two to five networking points directly and securely
at a distance of up to 7000’ line of site.
INCLUDED IN PACKAGE:
(1) AP dish
(1) Mount Assembly
(1) PoE Power Adapter
(1) AC Cord
(1) Package Mounting Hardware
OPERATING INSTRUCTIONS:
1) You will need two Cat5 cables for each dish to complete assembly
2) The PoE power adapter has 3 inputs. One is for the AC cord, and two are for networking. Please note the
PoE adapter and power cord are not designed for outdoor use and should be used indoors only.
a. The bottom of the adapter has two RJ45 connections. One marked POE and one marked LAN.
b. Using one Cat5 cable, connect one end to “LAN” and the
other end to your camera, recorder, PC, etc.
c. Use the other Cat5 cable to connect your AP dish to the
POE input.
3) Antennas should be mounted level with each other, and
transmission distance is greatly reduced if line of site is not clear
4) Antenna should always be mounted upright (RJ45 ports facing down) with port cover connected to ensure
maximum weather resistance.
5) Both RJ45 ports (black and yellow) on antenna are LAN connections.
6) DIP switch instructions:
Toggle 1 changes the mode of the dish. UP is access point (AP) mode for use with your recorder,
PC, etc.. DOWN is for use with your camera.
Toggles 2 through 6 are for matching AP dishes together. There are 32 various combinations
that can be made from the 5 keys, which corresponds to 32 different SSIDs and 32 different
segments. The chart below shows all possible combinations.
Toggles 7 & 8 are for point to multi-point functionality. To use up to 4 cameras with one
recorder, configure the DIP switches as follows:
1) On the recorder/PC/Switch side, switches 7 and 8 should remain up.
2) On the camera side, select one of 4 configurations for switches 7 and 8:
a. Camera 1: 7 Up and 8 Up
b. Camera 2: 7 Up and 8 Down
c. Camera 3: 7 Down and 8 Up
d. Camera 4: 7 Down and 8 Down
3) You cannot duplicate the switch settings between Cameras for switches 7 & 8 or you will
experience interference, thus the max of 4 points.
4) Each dish has a reception angle of 30 degrees horizontal and 60 degrees vertical.
SPECIFICATIONS:
Chipset Atheros AR9344 600MHz
DRAM DDR2 64MByte
FLASH
8MByte
IC
SiGe5004L
Port 10/100Mbps LAN*2
Speed
11a:54M,48M,36M,24M,18M,12M,9M,6Mbps
HT20:7.2M,14.4M,21.7M,28.9M,43.3M,57.8M,65M,72.2M,14.4M,
28.9M,43.3M,57.8M,86.7M,115.6M,130M,144.4Mbps
HT40:15M,30M,45M,60M,90M,120M,135M,150M,30M,60M,90M,120M,
180M,240M,270M,300Mbps
Transmission
DSSS, up to 7000’ line of sight with no interference
Dimensions 7.9” Diameter x 2.5” H (5.2” High with mount attached)
Modulation OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Standard IEEE802.11n,IEEE802.11g,IEEE802.11b,IEEE802.3u,IEEE802.3af
Protocol CSMA/CA,TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3,NDIS4,NDIS5
Channel AP200M: 2.372 ~ 2.532GHz AP300M: 4.96 6.065GHz ～
Power dissipation
≤6W
Power POE 24V 1A
RF
@25±2dB
802.11a
6-24Mbps
27±2dB
36-48Mbps 26±2dB
54Mbps
25±2dB
802.11n
HT20
MCS 0-3 27±2dB
MCS 4 26±2dB
MCS 5 25.5±2dB
MCS 6 25±2dB
MCS 7 24.5±2dB
HT40
MCS 0-3 26±2dB
MCS 4 25.5±2dB
MCS 5 25±2dB
MCS 6 24.5±2dB
MCS 7 24±2dB
Sensitivity
802.11a 6Mbps ≤ -89 54Mbps ≤ -73 ；
802.11n
HT20
MCS 0 ≤ -86; MCS 7 ≤ -68
HT40
MCS 0 ≤ -83; MCS 7 ≤ -65
Antenna
Frequency 4900 6100MHz ～
Direction Horizontal/Vertical
Gain
18DBi
Management
WEP management
Yes
SNMP MIB Yes
Telnet Yes
Serial Yes
Security
MAC address control
Yes
Encryption WEP 64/128bits,WPA,WPA2,802.1x
Operating conditions
Working temperature -22F~149F
Storage Temperature -58F~176F
Humidity (non-condensed) ≤95% NA（ ）

Especificaciones del producto

Marca: Speco Technologies
Categoría: repetidor wifi
Modelo: AP200M

¿Necesitas ayuda?

Si necesitas ayuda con Speco Technologies AP200M haz una pregunta a continuación y otros usuarios te responderán


repetidor wifi Speco Technologies Manuales

Speco Technologies

Speco Technologies AP200M Manual de Usario

18 Agosto 2024

repetidor wifi Manuales

Últimos repetidor wifi Manuales

Hawking Technologies

Hawking Technologies HOW2R1 Manual de Usario

14 Octubre 2024
Planet

Planet WNAP-1110 Manual de Usario

10 Octubre 2024
Netgear

Netgear WN2000RPTv2 Manual de Usario

10 Octubre 2024
Netgear

Netgear A7000 Manual de Usario

3 Octubre 2024
Ubiquiti Networks

Ubiquiti Networks MIMO Multiplexer Manual de Usario

3 Octubre 2024
Planet

Planet LRP-104CET Manual de Usario

30 Septiembre 2024
Netgear

Netgear WN2500RP Manual de Usario

30 Septiembre 2024
Totolink

Totolink EX200U Manual de Usario

29 Septiembre 2024
Silvercrest

Silvercrest SWV 300 B2 Manual de Usario

29 Septiembre 2024
Totolink

Totolink EX300 Manual de Usario

28 Septiembre 2024