Square Jellyfish Micro Ball Head Manual de Usario
Square Jellyfish
Trípode
Micro Ball Head
Lee a continuación 📖 el manual en español para Square Jellyfish Micro Ball Head (2 páginas) en la categoría Trípode. Esta guía fue útil para 5 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/2
www.squarejellysh.com
Designed in USA. Made in China. Patent pending.
Thank you for purchasing the Square Jellysh Micro Ball Head. This product is
designed for use with pocket cameras to add camera angle exibility to a tripod.
You will need two things:
• A camera weighing up to 9 oz. with a tripod screw mount.
• A tripod with a 1/4 x 20 standard camera thread screw. Alternatively, the
Square Jellysh Pocket Tripod may be also be used.
Set up in two
simple steps:
• Gently
thumb-tighten
the screw of the
Micro Ball Head
onto the screw
mount of your
pocket camera.
• Gently
thumb-tighten
the base of the
Micro Ball
Head onto
thread screw
of your tripod.
Position your camera
Once set-up is complete, you
can then position your camera
in a broad range or angles. The
built-in tension of the Ball Head
holds your camera rmly in place.
If desired, a small screwdriver
can be used to adjust the tension
looser or tighter by slightly turning
the recessed set-screw at the
bottom of the Micro Ball Head.
Use common sense
• Do not place your camera where it can easily fall a distance that would cause
damage to your camera.
• This product contains small parts that may be a chocking hazard. Keep out
of reach of children.
Micro Ball Head shown with
conventional tripod
Micro Ball Head shown with
Square Jellysh Pocket Tripod
SQUARE JELLYFISH MICRO BALL HEAD USER’S MANUAL
Square JellyfiSh Micro ball head ProducT warranTy
www.squarejellysh.com
Designed in USA. Made in China. Patent pending.
warninG
The Micro Ball Head is designed for use with pocket
cameras to add camera angle exibility to a tripod.
Be careful when positioning your camera so that it
does not fall over. You must take care to make sure
that the camera remains balanced after it is aimed by
making sure the thumb screws are tight enough. This
device is designed to support lightweight, compact
cameras up to 9 oz., and not heavy cameras, SLRs,
or any camera with a lengthy lens or similar extension.
Always support the camera with one hand while you
are tightening it in place with the other hand. While still
supporting it, wiggle the camera a bit to make sure
that it will not tip over when you release it, because
this might damage your camera! Only you can make a
safe evaluation of whether your camera is secure and
balanced because of the innite number of settings
which you may choose.
liMiTed warranTy
The Micro Ball Head is warranted against defects in
materials and workmanship for a period of ONE (1)
YEAR from the date of the original retail purchase. If
a defect exists the manufacturer will, at its option and
to the extent permitted by law, (1) repair the product
at no charge using new or refurbished parts; or (2)
exchange the product with a functionally equivalent
product that is new or refurbished; or (3) refund
the original purchase price. This warranty excludes
damage resulting from abuse, accident, modications
or other causes that are not defects in the materials or
workmanship. To the extent permitted by applicable
law, the manufacturer is not liable for any direct,
indirect, incidental or consequential damage arising
out of the use of service of the product, including, but
not limited to damage which may be caused to any
camera, or to any other device the Micro Ball Head is
used to support. To the extent permitted by applicable
law the manufacturer of the Micro Ball Head disclaims
all implied warranties of merchantability and tness
for a particular purpose. If implied warranties cannot
be disclaimed, then such warranties are limited in
duration to the duration of this warranty. This warranty
gives you specic legal rights, and you may have other
rights which vary from state to state.
To obtain warranty service, contact Square
Jellysh using the information provided at
www.squarejellysh.com
To the extent permitted by applicable law proof
of purchase for all warranty repairs/replacement
is required.
Especificaciones del producto
| Marca: | Square Jellyfish |
| Categoría: | Trípode |
| Modelo: | Micro Ball Head |
¿Necesitas ayuda?
Si necesitas ayuda con Square Jellyfish Micro Ball Head haz una pregunta a continuación y otros usuarios te responderán
Trípode Square Jellyfish Manuales
18 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
16 Septiembre 2024
Trípode Manuales
- Trípode Sony
- Trípode Silvercrest
- Trípode Kodak
- Trípode Carson
- Trípode Easypix
- Trípode Hama
- Trípode Velleman
- Trípode AVerMedia
- Trípode Celestron
- Trípode DJI
- Trípode Vello
- Trípode Rollei
- Trípode Magnus
- Trípode Zhiyun
- Trípode Miller
- Trípode Benro
- Trípode Vortex
- Trípode Sachtler
- Trípode Sevenoak
- Trípode Laserliner
- Trípode Celly
- Trípode Eurolite
- Trípode Proaim
- Trípode Revo
- Trípode Konig & Meyer
- Trípode Manfrotto
- Trípode Velbon
- Trípode ARRI
- Trípode Ultimate Support
- Trípode Levenhuk
- Trípode JOBY
- Trípode Oben
- Trípode Dorr
- Trípode Glide Gear
- Trípode Libec
- Trípode Kogan
- Trípode MOZA
- Trípode Flycam
- Trípode Gravity
- Trípode Sirui
- Trípode Vinten
- Trípode Neewer
- Trípode Ravelli
- Trípode Fidlock
- Trípode Vanguard
- Trípode SmallRig
- Trípode FeiYu-Tech
- Trípode FeiyuTech
- Trípode Sky-Watcher
- Trípode Hohem
- Trípode MOVE'N SEE
- Trípode On Air
- Trípode Kaiser Fototechnik
- Trípode Slidekamera
- Trípode IOptron
- Trípode FLOWCINE
- Trípode SteadiCam
- Trípode Fat Gecko
- Trípode 3 Legged Thing
- Trípode FLM
- Trípode Peak Design
- Trípode Easyrig
- Trípode Robus
- Trípode Studio Assets
- Trípode Stalco
- Trípode Tiltall
- Trípode E-Image
Últimos Trípode Manuales
26 Octubre 2024
25 Octubre 2024
17 Octubre 2024
8 Octubre 2024
3 Octubre 2024
2 Octubre 2024
2 Octubre 2024
1 Octubre 2024
24 Septiembre 2024
22 Septiembre 2024