Stanley STHR202 Manual de Usario
Stanley
Taladros de percusión
STHR202
Lee a continuación 📖 el manual en español para Stanley STHR202 (12 páginas) en la categoría Taladros de percusión. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/12
STHR202 English 3
简体中文 8
EF
C D
BA
* The picture above may differ slightly to actual unit.
3
9
10
9
11
2
3
1
4
5
6
48
7
4
13
14
12
3
ENGLISH
Intended use
Your Stanley SDS plus rotary hammer is intended to drill holes
in concrete, bricks, wood, and steel.
Safety instructions
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
The term “ ”power tool in the warnings refers to your mains-
operated (corded) power tool or battery-operated (cordless)
power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Rotary hammer STHR202
Power input W 620
Voltage V 220
Frequency Hz 50
No-load speed /min 0-1250
Impact rate BPM 0-3900
Impact energy J 1.34
Modes 2
Max drilling capacity mm
- Concrete 20
- Steel 13
- Wood 25
Weight kg 2.6
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed
or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric
shock.
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged
or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock. NOTE:
The term “residual current device (RCD)” may be replaced
by the term “ground fault circuit interrupter (GFCI)” or “earth
leakage circuit breaker (ELCB)”.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught
in moving parts.
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
STHR202
Rotary hammer
Technical data
Especificaciones del producto
| Marca: | Stanley |
| Categoría: | Taladros de percusión |
| Modelo: | STHR202 |
¿Necesitas ayuda?
Si necesitas ayuda con Stanley STHR202 haz una pregunta a continuación y otros usuarios te responderán
Taladros de percusión Stanley Manuales
15 Octubre 2024
Taladros de percusión Manuales
- Taladros de percusión AEG
- Taladros de percusión DeWalt
- Taladros de percusión Makita
- Taladros de percusión Tryton
- Taladros de percusión Hitachi
- Taladros de percusión Black And Decker
- Taladros de percusión Metabo
- Taladros de percusión Meec Tools
- Taladros de percusión Milwaukee
Últimos Taladros de percusión Manuales
17 Octubre 2024
15 Octubre 2024
12 Octubre 2024
11 Octubre 2024
11 Octubre 2024
10 Octubre 2024
9 Octubre 2024
22 Julio 2024
19 Julio 2024
19 Julio 2024