Star Micronics SM-S201 Manual de Usario
Star Micronics
Impresora de etiquetas
SM-S201
Lee a continuación 📖 el manual en español para Star Micronics SM-S201 (23 páginas) en la categoría Impresora de etiquetas. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios
Página 1/23
Mobile Printer
SM-S200 SERIES
Models: SM-S201
SM-S202
Hardware Manual
Federal Communications Commission
Radio Frequency Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
CAUTION: Changes or modications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modications not expressly approved by the manufacturer could void the user’s authority to operated the equipment under
FCC rules.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio
frequency (RF) Exposure Guidelines in Supplement C to OET65. This equipment has very low levels of RF energy that it is
deemed to comply without testing of specic absorption ratio (SAR).
The above statement applies only to equipments marketed in U.S.A.
Trademark acknowledgments
SM-S200: Star Micronics Co., Ltd.
Notice
• All rights reserved. Reproduction of any part of this manual in any form whatsoever, without
STAR’s express permission is forbidden.
• The contents of this manual are subject to change without notice.
• All efforts have been made to ensure the accuracy of the contents of this manual at the time of
going to press. However, should any errors be detected, STAR would greatly appreciate being
informed of them.
• The above notwithstanding, STAR can assume no responsibility for any errors in this manual.
© Copyright 2010 Star Micronics Co., Ltd.
Please follow the precautions below to enjoy and maintain the full performance of the printer.
■ Using the Printer
● Some semiconductor devices are easily damaged by static electricity. You should turn the
printer “OFF”, before you connect or removed the cable on the rear side, in order to guard
the printer against the static electricity. If the printer is damaged by the static electricity,
you should turn the printer “OFF”.
● Be careful not to drop or bump the printer on a hard surface.
● Do not install the printer in direct sunlight or such areas.
Suitable environment for the use of the printer is as follows:
Operating temperature :0 °C to 50 °C
Relative humidity : 30 % to 80 % (No condensation)
● Do not install the printer near devices that generate strong electromagnetic elds such as a
copy machine.
● Do not open the paper cover during printing .
● Do not remove or reinstall the communication cable during printing or transmission.
● Do not touch the connectors of the communication during printing.
● Switch the POWER OFF when not in use.
● Do not use alcohol or other solvent.
● The battery charger and the battery pack may become warm when in use. This is normal and
is not a malfunction.
● When the battery pack is used at low temperature, the length of time the printer can be used
may be shortened.
■ Thermal Paper Handling
● Store the thermal paper in a cool, dry and dark place.
● Do not rub the paper with hard object.
● Do not leave the paper with hard object.
● Do not allow plastic lm, erasers, or adhesive tape to touch the paper for long periods.
● Do not stack the thermal paper with diazo copies immediately after copying or wet-type
copies.
● Do not use chemical glue.
● Always use the clean thermal paper.
Operating precautions
Especificaciones del producto
| Marca: | Star Micronics |
| Categoría: | Impresora de etiquetas |
| Modelo: | SM-S201 |
¿Necesitas ayuda?
Si necesitas ayuda con Star Micronics SM-S201 haz una pregunta a continuación y otros usuarios te responderán
Impresora de etiquetas Star Micronics Manuales
12 Septiembre 2024
28 Agosto 2024
24 Agosto 2024
Impresora de etiquetas Manuales
- Impresora de etiquetas Casio
- Impresora de etiquetas Honeywell
- Impresora de etiquetas Toshiba
- Impresora de etiquetas Brother
- Impresora de etiquetas Renkforce
- Impresora de etiquetas Citizen
- Impresora de etiquetas Seiko
- Impresora de etiquetas Argox
- Impresora de etiquetas Dymo
- Impresora de etiquetas Bixolon
- Impresora de etiquetas Zebra
- Impresora de etiquetas Leitz
- Impresora de etiquetas GoDEX
- Impresora de etiquetas POSline
- Impresora de etiquetas Brady
- Impresora de etiquetas Datamax-O'neil
- Impresora de etiquetas Primera
- Impresora de etiquetas TSC
- Impresora de etiquetas SII
- Impresora de etiquetas Start International
- Impresora de etiquetas Qian
- Impresora de etiquetas Custom
Últimos Impresora de etiquetas Manuales
27 Octubre 2024
27 Octubre 2024
18 Octubre 2024
16 Octubre 2024
16 Octubre 2024
15 Octubre 2024
13 Octubre 2024
11 Octubre 2024
10 Octubre 2024
8 Octubre 2024