StarTech.com PEX10GSFP Manual de Usario

StarTech.com Tarjeta/adaptador de red PEX10GSFP

Lee a continuación 📖 el manual en español para StarTech.com PEX10GSFP (2 páginas) en la categoría Tarjeta/adaptador de red. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Quick-Start Guide

To view manuals, FAQs, videos, drivers, downloads, technical drawings, and more, visit www.startech.com/support.

Manual Revision: March 10, 2022 11:40 AM

Product Diagram (PEX10GSFP)

Component Function

1SFP+ Slot • Connect a 10G SFP+ Transceiver Module to the

PCI Express Card.

2Link/Activity LED

• Solid Green: Network Device A link to a has

been established.

• Flashing Green: Indicates network activity.

3PCI Express Connector

(x4)

• Used to connect the to the PCI Express Card

Host Computer.

• Gen 3 connection.

Package Contents

• Network Card x 1

• Low-Prole Bracket x 1

• Quick-Start Guide x 1

Requirements

For the latest requirements, please visit www.startech.com/PEX10GSFP

• PCI Express enabled computer with an available PCI Express p1-x4 slot

• 10G SFP+ Transceiver Module

1 Port PCI Express 10GbE SFP+ Network Adapter Card

Hardware Installation

Installing the Low Prole Bracket

By default the is attached to the . Depending Full Prole Bracket PCI Express Card

on your system conguration you may need to remove the and Full Prole Bracket

replace it with the (included).Low Prole Bracket

1. Using a , remove the two securing Small Phillips Head Screwdriver Bracket Screws

the to the .Full Prole Bracket PCI Express Card

2. Align the on the with the on theScrew Holes PCI Express Card Screw Holes Low

Prole Bracket PCI Express Card Screw . Making sure the is sitting on-top of the

Holes Low Prole Bracket on the .

3. Insert the through the and into the Bracket Screws PCI Express Card Screw Holes

on the . Low Prole Bracket

4. Using the , tighten the , being Small Phillips Head Screwdriver Bracket Screws

careful not to over-tighten.

Installing the PCI Express Card

Static Electricity PCI Express Cardscan severely damage . Ensure that you are

adequately before you open your or touch the Grounded Computer Case PCI

Express Card Anti-Static Strap Anti-Static Mat . You should wear an or use an when

installing any computer component. If an isn’t available, discharge Anti-Static Strap

any built-up static electricity by touching a large for several Grounded Metal Surface

seconds. Only handle the by its edges and don’t touch the gold PCI Express Card

connectors.

1. Turn o the and any connected to the Host Computer Peripherals Devices

computer (e.g. printers, external hard drives, etc.).

2. Unplug the from on the back of the and disconnect all Power Cable Host Computer

Peripheral Devices.

3. Remove the from the (refer to the documentation that Cover Host Computer Case

came with the for further details).Host Computer

4. Locate an open and remove the metal cover plate on the rear of PCI Express p1-x4 Slot

the (See documentation for your computer system for details).Computer Case

Note: This card will work in of additional lanes (e.g. x8, or x16 PCI Express Slots

slots).

5. Gently insert the into an open and fasten the PCI Express Card PCI Express Slot

Bracket Computer Case to the rear of the .

6. Place the back onto the .Cover Computer Case

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation. Changes or modications not expressly approved by StarTech.com could void

the user’s authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du Canada.

CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) This device may not cause interference, and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation

est autorisée aux deux conditions suivantes:

(1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d’en compromettre le fonctionnement.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-

party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only

and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which

this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered

trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the

property of their respective holders.

Warranty Information

This product is backed by a two-year warranty.

For further information on product warranty terms and conditions, please refer to .www.startech.com/warranty

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their ocers, directors, employees or agents)

for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of prots, loss of

business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product.

Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations

or exclusions contained in this statement may not apply to you.

Safety Measures

• If product has an exposed circuit board, do not touch the product under power.

Mesures de sécurité

• Si l’un des circuits imprimés du produit est visible, ne pas touchez le produit lorsqu’il est sous tension.

安全対策

•  製品に露出した状態の回路基盤が含まれる場合、電源が入っている状態で製品に触らないでください。

Misure di sicurezza

• Se il prodotto ha un circuito stampato visibile, non toccare il prodotto quando è acceso.

Säkerhetsåtgärder

• Rör aldrig vid enheter med oskyddade kretskort när strömmen är påslagen.

FR: startech.com/fr

DE: startech.com/de

ES: startech.com/es

NL: startech.com/nl

IT: startech.com/it

JP: startech.com/jp

StarTech.com Ltd.

45 Artisans Crescent

London, Ontario

N5V 5E9

Canada

StarTech.com Ltd.

Unit B, Pinnacle 15

Gowerton Road

Brackmills,

Northampton

NN4 7BW

United Kingdom

StarTech.com LLP

4490 South Hamilton

Road

Groveport, Ohio

43125

U.S.A.

StarTech.com Ltd.

Siriusdreef 17-27

2132 WT Hoofddorp

The Netherlands

7. Insert the of your choice, compatible with your 10G SFP+ Transceiver Module

network, into the on the .SFP+ Slot PCI Express Card

8. Insert the into the socket on the power supply and reconnect all other Power Cable

connectors removed in .Step 1

Note: The 10G ber card is compatible with transceiver modules only.10G SFP+

Driver Installation

When the is installed the drivers should install automatically. If the PCI Express Card

drivers do not automatically install, follow the next steps.

1. Navigate to www.startech.com/PEX10GSFP

2. Click the tab.Drivers/Downloads

3. Under , download the for your operating system.Driver(s) Driver

4. Extract the contents of the package. Follow the on-screen instruction of the Driver

Installer Package Driver to nish installing the .

Connecting to a Network

1. Insert a compatible , into the on the 10G SFP+ Transceiver Module SFP+ Slot PCI

Express Card.

2. Connect a or to the Fiber Network Cable Cat5e/6 Cable 10G SFP + Transceiver Module

and the other end to a or on a 10G Fiber Port RJ45 Port Network Device.

Especificaciones del producto

Marca:	StarTech.com
Categoría:	Tarjeta/adaptador de red
Modelo:	PEX10GSFP

¿Necesitas ayuda?

Si necesitas ayuda con StarTech.com PEX10GSFP haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

Tarjeta/adaptador de red StarTech.com Manuales

StarTech.com ST1000SPEXD4T Manual de Usario

22 Octubre 2024

StarTech.com ST1000SPEX2T Manual de Usario

3 Octubre 2024

StarTech.com ST1000SPEX2LT Manual de Usario

3 Octubre 2024

StarTech.com AF221CE-POE-INJECTOR Manual de Usario

1 Octubre 2024

StarTech.com USB3LINK Manual de Usario

26 Septiembre 2024

StarTech.com PCMACLINK2 Manual de Usario

26 Septiembre 2024

StarTech.com PEX1000SFP Manual de Usario

26 Septiembre 2024

StarTech.com ST2GPEX Manual de Usario

26 Septiembre 2024

StarTech.com USB56KEM2 Manual de Usario

26 Septiembre 2024

StarTech.com PUSBADAP Manual de Usario

26 Septiembre 2024

Tarjeta/adaptador de red Manuales

Últimos Tarjeta/adaptador de red Manuales

Cambium Networks CG52A Manual de Usario

26 Octubre 2024

Devolo MicroLink dLAN duo Manual de Usario

16 Octubre 2024

Edimax HP-5001K Manual de Usario

16 Octubre 2024

LevelOne FNC-0109TX Manual de Usario

14 Octubre 2024

Edimax EW-7822ULC Manual de Usario

9 Octubre 2024

ZyXEL AP Configurator Manual de Usario

6 Octubre 2024

Linksys AE1000 Manual de Usario

6 Octubre 2024

Trendnet TEW-624UB Manual de Usario

5 Octubre 2024

Nec NP06LM Manual de Usario

4 Octubre 2024

Alecto HPD-142 Manual de Usario

4 Octubre 2024