Techno Line WS 9251 Manual de Usario

Techno Line Estación meteorológica WS 9251

Lee a continuación 📖 el manual en español para Techno Line WS 9251 (6 páginas) en la categoría Estación meteorológica. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/6
Please read the instructions carefully and keep the manual well for future reference.
1. Remove the battery door of the main unit and transmitter.
2. Install 2 new AA size batteries for both main unit and transmitter, according to the polarity mark on
the battery compartment.
3. Replace the battery door.
4. After the batteries are installed, all LCD segment will be shown.
5. Press the “RESET” key of main unit first, and press the “RESET” key of transmitter.
6. It will automatically receive 433 MHz signal from transmitter for channel test in 8 seconds.
7. After 5 minutes channel test, it will turn to RC signal reception automatically.
8. Radio Controlled function, the current time & date automatically synchronized with the time signal
transmitted from Germany(DCF77).
1. The unit can operate up to 3 remote transmitters.
2. Position the unit and transmitter within the effect transmission range: 50 meters in usual ive
circumstances.
3. In some cases, you may not receive the signal immediately, you can reset the unit and transmitter
again as described above.
1. LCD display
- Display of the time, alarm time, outdoor & indoor temperature and weather forecast.
2. SNOOZE / LIGHT key
- Press it to turn on backlight for 5 seconds.
- When the alarm is sounding, press it to stop the current alarm and activate snooze.
3. ALARM SET key
- Press it to display alarm time for 5 seconds. During alarm time displayed, press it to turn on/ off alarm
function.
- Press and hold it for 3 seconds to enter alarm setting mode.
- In alarm setting mode, press it to step the setting item, and press it to save and exit the setting.
4. CH/+ key
- In normal mode, press it to select channel 1 to channel 3.
- Press and hold it for 3 seconds to turn to channel auto-change mode. Press it again to return to
normal mode.
- In setting mode, press it to adjust the value of the flashing digit upwards. And press it without
releasing to speed up the setting.
5. MEM/- key
- In normal mode, press it to check the max./min. indoor and outdoor temperature record for 5 seconds.
- Press and hold it for 3 seconds to delete the max./min. temperature record.
- In setting mode, press it to adjust the value of the flashing digit downwards. And press it without
releasing to speed up the setting.
6. DISPLAY SET key
- In normal mode, press and hold it for 3 seconds to enter time setting mode.
- In time setting mode, press it to step the setting item, and press and hold it for 3 seconds to save and
exit the setting.
7. °C/°F slide switch
- Select temperature unit between °C/°F.
8. SENSOR key
- Press it to start 433 MHz channel test for main unit & transmitter.
- During the channel test, press and hold it for 3 seconds to manual turn off.
9. RCC key
- Press it to manual receive RC signal.
- During the RC reception, press and hold it for 3 seconds to turn off synchronisation.
10. RESET key
- In case of mal-function, press it by using a metal wire to reset all the values.
11. Battery door
1. LED indicator
- Flashes when the remote unit transmitting a reading.
2. CHANNEL slide switch
- Assign the transmitter to Channel 1, 2 or 3.
3. RESET key
- Press it to reset the transmitter.
4. Wall-mounting holder
- Use it to support the transmitter on the wall.
5. Battery compartment
The signal indicator flashing means time signals are being received. If the RC weather station receives
signal successfully, a sync-time symbol “ ” appears on the LCD. The unit has already received the
time signal. Otherwise, the signal strength symbol will disappear from the LCD display.
You may press “RCC” key to receive the time signal manually. The receive mode will be off
automatically after 6-16 minutes. Receive mode consumes more battery power that may reduce
battery lifetime.
The weather station has been programmed to automatically switch when daylight saving time is in
effect. Your clock will display “DST” on the LCD during the summer.
If the weather station does not receive the time signal successfully, you can set the time manually. As
soon as the transmitter is received again, the weather station will automatically synchronize with the
received time.
1. In normal mode, press and hold “DISPLAY SET” key for 3 seconds until the Hour format digit
flashing.
2. Press “+” / “ ” key to select 12/24 hour format.-
3. Press “DISPLAY SET” key again to step the setting item to Hour with the Hour digit flashing.
4. Press “+” / “ ” key to adjust the value of the- flashing digit.
5. Do the above operation in this sequence: 12/24 Hr > Hour > Minute > Second > Time difference.
6. Press and hold “DISPLAY SET” key for 3 seconds to save and exit the setting.
If your local time is different from the RC received time, you can set the desired time difference. The
available time difference is from -23 hours to +23 hours. After setting the desired time difference, the
weather station will show the time that RC received time plus/minus the time difference.
1. In normal mode, press and hold “ALARM SET” key for 3 seconds until the Hour digit flashing.
2. Press “+” / “ ” key to adjust the- value of the flashing digit.
3. Press “ALARM SET” key again to step the setting value to Minute with the Minute digit flashing.
4. Press “+” / “ ” key to adjust the value of the- flashing digit.
5. Press “ALARM SET” key to save and exit the setting.
1. In alarm mode, the “AL” icon will display on the LCD.
2. The alarm function will turn on automatically once you set the alarm time.
1. Set the desired alarm time as described in the above section.
2. Or press “ALARM SET” key to display the alarm time, press it again to turn on alarm function with
the alarm icon “ ” displayed on the LCD.
3. When clock reach the alarm time, alarm sound will start. Where, it can be stopped by following
operation:
a). Auto-stop after two minutes alarming if without any operation and it will re-alarm by the next day.
b). By pressing “SNOOZE” key to enter snooze that the alarm will sound again after 5 minutes.
c). By pressing “ALARM SET” key to turn off the alarm function.
1. The snooze could be used continuously in 24 hours.
2. During the snooze, the alarm icon will keep flashing.

Especificaciones del producto

Marca: Techno Line
Categoría: Estación meteorológica
Modelo: WS 9251

¿Necesitas ayuda?

Si necesitas ayuda con Techno Line WS 9251 haz una pregunta a continuación y otros usuarios te responderán


Estación meteorológica Techno Line Manuales

Techno Line

Techno Line WS 6448 Manual de Usario

16 Septiembre 2024
Techno Line

Techno Line WS 9245-IT Manual de Usario

15 Septiembre 2024
Techno Line

Techno Line WS 7208 Manual de Usario

14 Septiembre 2024
Techno Line

Techno Line WS 6762 Manual de Usario

14 Septiembre 2024
Techno Line

Techno Line MA12024 Manual de Usario

7 Septiembre 2024
Techno Line

Techno Line WS 9611 IT Manual de Usario

3 Septiembre 2024
Techno Line

Techno Line MA 10001 Manual de Usario

2 Septiembre 2024
Techno Line

Techno Line WS6825 Manual de Usario

2 Septiembre 2024
Techno Line

Techno Line WS 9273-IT Manual de Usario

2 Septiembre 2024
Techno Line

Techno Line WS 6730 Manual de Usario

2 Septiembre 2024

Estación meteorológica Manuales

Últimos Estación meteorológica Manuales

Ascot

Ascot GT-WS-07s Manual de Usario

20 Octubre 2024
Ventus

Ventus K0382 Manual de Usario

18 Octubre 2024
Hyundai

Hyundai WSP 3080 Manual de Usario

15 Octubre 2024
La Crosse Technology

La Crosse Technology V61 Manual de Usario

8 Octubre 2024
Cresta

Cresta WX580M Manual de Usario

6 Octubre 2024
Sencor

Sencor SWS 65 Manual de Usario

5 Octubre 2024
Irox

Irox JKR-1 Manual de Usario

5 Octubre 2024
TFA

TFA 30.5002 Manual de Usario

5 Octubre 2024
TFA

TFA WeatherHub 30.3306.02 Manual de Usario

4 Octubre 2024
Jung

Jung WS10R Manual de Usario

4 Octubre 2024