Tenda EX3 Manual de Usario

Tenda No categorizado EX3

Lee a continuación 📖 el manual en español para Tenda EX3 (3 páginas) en la categoría No categorizado. Esta guía fue útil para 2 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

2. Connect the mobile phone to the WiFi network of the node. The SSID and password can

be found on the bottom label of the device.

Tenda WiFi

3. Run the Tenda WiFi App and follow the onscreen instructions to connect the device to the

internet. After the device is connected to the internet, its LED indicator lights solid green.

2. Start a browser on the client and enter tendawifi.com in the address bar to access the web UI, and

follow the onscreen instructions to connect the device to the internet.

Method 2: Setup through web UI

1. Connect the client to the node.

Method 1: Connect the wireless client such as a mobile phone to the WiFi network of the node.

The SSID and password can be found on the bottom label of the device.

Method 2: Use an Ethernet cable to connect the computer to the LAN port of the node.

Tips

If you cannot log in to the web UI, refer to Q1 in .FAQ

NOVA_XXXX_XX

Settings Wi-Fi

Wi-Fi

CHOOSE A NET WORK…

Done.

• To access the internet with:

- Wired devices: Connect to the LAN port of your node.

- Wireless devices: Connect to your WiFi network using the WiFi name and password you set.

• If you want to manage the network remotely, tap on the App home page and use your account

to log in.

Done.

To access the internet with:

- Wired devices: Connect to the LAN port of your node.

- Wireless devices: Connect to your WiFi network using the WiFi name and password you set.

1. Power off your modem.

2. Use the included Ethernet cable to connect the WAN/LAN port to your modem or the Ethernet

jack.

3. Power on your modem.

4. Power on the node, and wait until the LED indicator blinks green.

Tips

If you do not use a modem for internet access, please skip steps and 1 3.

I Connect the node

Scenario1: Set up as your first nova node

1. Plac .

mpletes startup when its LED indicator

blinks green slowly.

3. Press the button of the node for about 1 to 3 seconds. The LED indicator blinks green MESH

fast. Within 2 minutes, press the MESH button of the node of the existing network for 1 to

3 seconds to negotiate with this node.

Tips

• Please ensure that the node has never been used. If not, reset it first.

• Currently, the node can be networked with Tenda's Wi-Fi 6 routers that support the

EasyMesh protocol.

I Add the node to an existing network

Scenario2: Set up as an add-on nova node

Method 1: Setup through Tenda WiFi App

1. Download the Tenda WiFi App onto your mobile device by scanning the code or by QR

searching for Tenda WiFi Google Play in or App Store. Then install the Tenda WiFi App.

II Connect the node to the internet

Original node Add-on node

Dual-band Whole Home Mesh Wi-Fi 6 System

MX3/EX3

Quick Installation Guide

Package contents Appearance

• Mesh3X x 1

• Power adapter x 1

• Ethernet cable x 1

• Quick installation guide x 1

Please read th is guide befo re you start with the quick setup upon the first u se. You can see the produ ct name and

model on the product label.

MX3 i s used for illu stration here unles s otherwise spec ified. The actual pro duct prevails .

This guide instructs how to install and connect the device. For more information such asthe des cription of sym bols

displaye d on relevant materials, please visit w ww.tendacn.com or scan the Pr od uct Do cument s QR code in th is guide.

Reset button

MESH button MES H PWRLANWAN/LAN

RST

MESH PWRLANWAN LAN

RST

MESH PWRLAWAN/LAN

RST

Gigabit WAN/LAN

multiplexing port,

WAN port by default

Gigabit LAN port

Power jack

Power outlet

Ethernet cable

LED indicator

NOVA_XXXX_XX

Power outlet

Ethernet jack

Internet

Modem (such as

optical modem)

Gigabit port

Ethernet cable

Tips

Do not hold down the MESH button for 8 seconds if unnecessary.

MESH

RST

MESH button.

− As a networking button: Press this button on this device for about 1 to 3 seconds.

The LED indicator blinks green fast, which indicates the device is searching for

another device to form a network. Within 2 minutes, press the MESH button of

another device for 1 to 3 seconds to negotiate with this device.

− As a de-networking button: Press this button for about 8 seconds and release it

when the LED indicator blinks red fast. The node is restored to factory settings,

and also removed from the network and no longer automatically joins in again.

Reset button.

When the device completes startup, hold down this button using a needle-like

item (such as a pin) for about 8 seconds, and then release it when the LED

indicator blinks red fast. The device is reset successfully.

Button Description

When the LED indicator of the node lights solid green, the networking is successful and the

node becomes a secondary node in the network.

1.Refer to the following relocation tips to locate the node to a proper position:

• Ensure that the distance between any two nodes is less than 10 meters.

• Keep your nodes away from electronics with strong interference, such as microwave ovens,

induction cookers, and refrigerators.

• Place the nodes in a high position with few obstacles.

2.Power on the node again till the LED indicator blinks green slowly.

Solid green Networking succeeds. Excellent connection quality.

Tips

If the LED indicator of node keeps blinking green slowly for more than 3 minutes, relocate

the node and move it closer to the primary node.

3. Observe the LED indicator of the node until the LED indicator lights one of the following colors:

Solid yellow Networking succeeds. Fair connection quality.

Solid red Networking succeeds. Poor connection quality.

4. If the node's LED indicator lights solid red, relocate it by repeating the preceding steps to get an

optimal connection quality.

Done.

To access the internet with:

- Wired devices: Connect to the LAN ports of your nodes.

- Wireless devices: Connect to your WiFi network using the WiFi name and password of your

existing nova WiFi network.

II Relocate the node

Q1: I cannot log in to the web UI by visiting tendawifi.com. What should I do?

A1: Try the following solutions:

• If you are using a wireless device, such as a smartphone:

− Ensure that it is connected to the WiFi network of the node.

− Ensure that the cellular network (mobile data) of the client is disabled.

• If you are using a wired device, such as a computer:

− Ensure that tendawifi.com is entered correctly in the address bar, rather than the search bar

of the web browser.

− Ensure that the computer is connected to the LAN port of the node properly using an Ethernet

cable.

− Ensure that the computer is set to obtain an IP address automatically and obtain DNS

server address automatically.

If the problem persists, please reset the node by referring to and try again. Q2

Q3: The device failed to be detected by the Tenda WiFi app upon my first time using the device.

What should I do?

A3: Try the following solutions:

1. Ensure that your mobile phone is connected to the default WiFi network of the device.

2. Ensure that the network permission of Tenda WiFi app is enabled, you can tap Settings >

Tenda WiFi to enable it.

If the problem persists, please reset the node and try again.

Q2: How to restore my device to factory settings?

A2: When your device is working properly, hold down the RST button of your device using a

needle-like item (such as a pin) for about 8 seconds, and release it when the LED indicator blinks

red fast. When the LED indicator lights solid green, your device is reset successfully.

FAQ LED indicator status

Solid green Connected to the internet.

Solid yellow Networking succeeds. Fair connection quality.

Solid red Networking succeeds. Poor connection quality.

Blinking green slowly Waiting to connect to other nodes.

Blinking green fast Networking by MESH button.

Blinking red slowly Failed to connect to the internet.

Description

After the device is powered on for about 40 seconds, the system completes startup. The status of the

LED indicator is shown in the following table.

LED indicator status

Q4: When I use the node as a single router, I cannot access the internet after the

configuration. What should I do?

A4: Try the following solutions:

• Check whether the WAN port of the node is connected to a modem or Ethernet jack properly.

• Log in to the web UI of the node and navigate to the Internet Settings page. Follow the

instructions on the page to solve the problem.

If the problem persists, try the following solutions:

• For WiFi-enabled devices:

− Check whether your WiFi-enabled devices are connected to the WiFi network of the node.

− Visit tendawifi.com to log in to the web UI and change your WiFi name and WiFi password

on the WiFi Settings page. Then try again.

• For wired devices:

− Check whether your wired devices are connected to a LAN port properly.

− Check whether wired devices are set to obtain an IP address automatically and obtain

DNS server address automatically.

This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may

be required to take adequate measures.

Operations in the 5.15-5.25GHz band are restricted to indoor use only.

This equipment should be installed and operated with a minimum distance 20cm between the device and your body.

The mains plug is used as disconnect device, the disconnect device shall remain readily operable.

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this

equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

Declaration of Conformity

Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the device is in compliance with Directive 2014/53/EU.

The full text of the EU declaration of conformity is available at the following internet address:

https://www.tendacn.com/download/list-9.html

Operating Frequency:

2.4 GHz: EU/2412–2472 MHz

5 GHz: EU/5150–5250 MHz

EIRP Power (Max.):

2.4 GHz: <20 dBm

5 GHz: <23 dBm

Software Version: V16.03.31. (Mesh3X, MX3, EX3)

Caution:

Adapter Model: BN073-A12012E/BN073-A12012B/BN073-A12012U/BN036-A12012D

Input: 100 - 240V AC, 50/60Hz, 0.4A

Output: 12V DC, 1.0A

Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO., LTD.

: DC Voltage

CE Mark Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

− Reorient or relocate the receiving antenna.

− Increase the separation between the equipment and receiver.

− Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

− Consult the dealer or an experienced radio/TV technician for help.

The device is for indoor usage only.

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired operation.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with

Part 15 of the FCC RF Rules.

This equipment should be installed and operated with minimum distance 20cm between the device and your body.

Caution:

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority

to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Operating frequency: 2412-2462 MHz, 5150-5250 MHz, 5725-5850 MHz

NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this

equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.

FCC Statement

Get support and services

Scan the Product Documents QR code to get related documents, such as the datasheet and user guide.

* The product model can be found on the label of the device.

Wall Mounting

This device can be installed on the wall with two screws and two expansion bolts. The recommended wall mounting tools

are as follows:

[Expansion bolt] Outer diameter: 6.0mm; Length: 26.4mm

[Screws] PA3*14mm; Head diameter: 5.2mm

Product Documents

(such as datasheet and user guide)

LED indicator

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this

product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its

impact on the environment.

User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical

or electronic equipment.

Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other brand and product names

mentioned herein are trademarks or registered trademarks of their respective holders. Specifications are subject to

change without notice.

Safety Precautions

V1.0 Keep for future reference.

Before performing an operation, read the operation instructions and precautions to be taken, and follow them to prevent

accidents. The warning and danger items in other documents do not cover all the safety precautions that must be followed.

They are only supplementary information, and the installation and maintenance personnel need to understand the basic

safety precautions to be taken.

- For desktop mounting, the device must be horizontally mounted for safe use.

- For wall mounting, the device is only suitable for mounting at heights ≤ 2 m.

- Do not use the device in a place where wireless devices are not allowed.

- Please use the included power adapter.

- The mains plug is used as the disconnect device, and shall remain readily operable.

- The power socket shall be installed near the device and easily accessible.

- Operating environment: Temperature: 0 ; Humidity: (10% - 90%) RH, non-condensing; Storage environment: ℃ ℃ - 40

Temperature: -40℃ - 70℃; Humidity: (5% - 90%) RH, non-condensing.

- Keep the device away from water, fire, high electric field, high magnetic field, and inflammable and explosive items.

- Unplug this device and disconnect all cables during lightning storms or when the device is unused for long periods.

- Do not use the power adapter if its plug or cord is damaged.

- If such phenomena as smoke, abnormal sound or smell appear when you use the device, immediately stop using it and

disconnect its power supply, unplug all connected cables, and contact the after-sales service personnel.

- Disassembling or modifying the device or its accessories without authorization voids the warranty, and might cause

safety hazards.

UK(NI)

For EU/EFTA, this product can be used in the following countries:

Shenzhen Tenda Technology Co., Ltd.

Floor 6-8, Tower E3, No.1001, Zhongshanyuan Road, Nanshan District, Shenzhen, China. 518052

Website: www.tendacn.com

E-mail: support.nova@tenda.com.cn

support.de@tenda.cn

support.fr@tenda.cn

support.es@tenda.cn

support.it@tenda.cn

support.uk@tenda.cn

Technical Support

Especificaciones del producto

Marca:	Tenda
Categoría:	No categorizado
Modelo:	EX3

¿Necesitas ayuda?

Si necesitas ayuda con Tenda EX3 haz una pregunta a continuación y otros usuarios te responderán

Tu nombre*

Tu correo electrónico*

Escribe tu pregunta aquí

No categorizado Tenda Manuales

Tenda TES7008 Manual de Usario

20 Septiembre 2024

Tenda IT7-LCS Manual de Usario

19 Septiembre 2024

Tenda RP7 Manual de Usario

14 Septiembre 2024

Tenda RH7-WCA Manual de Usario

7 Septiembre 2024

Tenda CH7-WCA Manual de Usario

7 Septiembre 2024

Tenda N3L-16H Manual de Usario

5 Septiembre 2024

Tenda EX3 Manual de Usario

30 Agosto 2024

Tenda MX21 Pro Manual de Usario

28 Agosto 2024

Tenda TEG1016G Manual de Usario

12 Agosto 2024

Tenda IT7-LRS Manual de Usario

12 Agosto 2024

No categorizado Manuales

Últimos No categorizado Manuales

POLARIS RZR S 1000 EPS (2018) Manual de Usario

27 Octubre 2024

Workzone 20V Li-Ion Reciprocating Saw PT160501 Manual de Usario

27 Octubre 2024

Philips 43PUL7672 Manual de Usario

27 Octubre 2024

Manhattan 461504 Manual de Usario

27 Octubre 2024

Sungrow SG125HV Manual de Usario

27 Octubre 2024

Schneider CCT724319 Manual de Usario

27 Octubre 2024

Technoline WS 250 Manual de Usario

27 Octubre 2024

Livarno IAN 354423 Manual de Usario

27 Octubre 2024

Kupper 12152 Manual de Usario

27 Octubre 2024

JennAir CARBON24L Manual de Usario

27 Octubre 2024