The T.bone free solo PT Manual de Usario

The T.bone micrófono free solo PT

Lee a continuación 📖 el manual en español para The T.bone free solo PT (56 páginas) en la categoría micrófono. Esta guía fue útil para 4 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF
Página 1/56
free solo PT
UHF wireless system
user manual
Musikhaus Thomann
Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: +49 (0) 9546 9223-0
E-mail: info@thomann.de
Internet: www.thomann.de
15.07.2021, ID: 296201, 296204, 296206, ... (V7)
Table of contents
1 General information 5.................................................................................................................................
1.1 Further information........................................................................................................................... 6
1.2 Notational conventions.................................................................................................................... 7
1.3 Symbols and signal words............................................................................................................... 8
2 Safety instructions 9.....................................................................................................................................
3 Features 12.......................................................................................................................................................
4 Installation and starting up 14................................................................................................................
4.1 General Information........................................................................................................................ 14
4.2 Receiver............................................................................................................................................... 15
4.3 Transmitter......................................................................................................................................... 17
5 Connections and operating elements 19...........................................................................................
5.1 Receiver............................................................................................................................................... 19
5.2 Transmitter......................................................................................................................................... 27
6 Operating 32....................................................................................................................................................
6.1 Receiver............................................................................................................................................... 32
Table of contents
free solo PT
3
6.2 Transmitter......................................................................................................................................... 36
7 Technical 40specications.......................................................................................................................
7.1 Transmitter......................................................................................................................................... 40
7.2 Receiver............................................................................................................................................... 43
8 Plug and connection assignment 46....................................................................................................
9 Troubleshooting 49......................................................................................................................................
10 Protecting the environment 52..............................................................................................................
Table of contents
UHF wireless system
4
1 General information
This user manual contains important information on the safe operation of the device. Read and
follow all safety notes and all instructions. Save this manual for future reference. Make sure
that it is available to all persons using this device. If you sell the device to another user, be sure
that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐
fore reserve the right to make changes without notice. Please refer to the latest version of the
user manual which is ready for download under .www.thomann.de
General information
free solo PT
5
1.1 Further information
On our website ( you will lots of further information and details on thewww.thomann.de) nd
following points:
Download This manual is also available as PDF for you to download.le
Keyword search Use the search function in the electronic version to the topics ofnd
interest for you quickly.
Online guides Our online guides provide detailed information on technical basics
and terms.
Personal consultation For personal consultation please contact our technical hotline.
Service If you have any problems with the device the customer service will
gladly assist you.
General information
UHF wireless system
6
1.2 Notational conventions
This manual uses the following notational conventions:
The letterings for connectors and controls are marked by square brackets and italics.
Examples: control, button.[VOLUME] [Mono]
The individual steps of an instruction are numbered consecutively. The result of a step is
indented and highlighted by an arrow.
Example:
1. Switch on the device.
2. Press .[Auto]
ðAutomatic operation is started.
3. Switch the device.o
Letterings
Instructions
General information
free solo PT
7
1.3 Symbols and signal words
In this section you will an overview of the meaning of symbols and signal words that arend
used in this manual.
Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Warning signs Type of danger
Warning – danger zone.
General information
UHF wireless system
8
2 Safety instructions
This device is intended to be used for the wireless transmission of audio signals from micro‐
phones or instruments to or active speakers. Use the device only as described in thisampliers
user manual. Any other use or use under other operating conditions is considered to be
improper and may result in personal injury or property damage. No liability will be assumed for
damages resulting from improper use.
This device may be used only by persons with physical, sensorial, and intellectualsucient
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking
hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke! Never let children unattended use electrical devices.
Intended use
Safety instructions
free solo PT
9
NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid
direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions in the chapterspecied
‘Technical of this user manual. Avoid heavy temperature and do not switch the device on immediatelyspecications’ uctuations
after it was exposed to temperature (for example after transport at low outside temperatures). Dust and dirt inside canuctuations
damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by
qualied service personnel at regular intervals to prevent overheating and other malfunction.
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the external power supply, ensure that the input voltage (AC
outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do
so could result in damage to the device and possibly the user. Unplug the external power supply before electrical storms occur and
when the device is unused for long periods of time to reduce the risk of electric shock or re.
NOTICE!
Risk of due to incorrect polarityre
Incorrectly inserted batteries may destroy the device or the batteries. Ensure that proper polarity is observed when inserting bat‐
teries.
Safety instructions
UHF wireless system
10
NOTICE!
Possible damage by leaking batteries
Leaking batteries can cause permanent damage to the device. Take batteries out of the device if it is not going to be used for a
longer period.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your parquet, linoleum, laminate
or PVC and after some time cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the butoor oor,
use felt-pad protectors or a carpet.oor
Safety instructions
free solo PT
11
3 Features
The UHF wireless system is particularly suitable for professional audio transmission, for
example, at events, on rock stages and in concert halls, theatres, musicals or night clubs.
Your UHF wireless system free solo PT consists of the following components:
n9.5" diversity receiver
– Two antennas for optimum reception quality
– Automatic frequency scanning
– Infrared interface for sending the frequency selection from the receiver to the trans‐
mitter
– Very high sensitivity at very high signal-to-noise ratio
– Adjustable Squelch
– Outputs: XLR, 1/4" jack socket
– Mounting brackets for mounting in a 19" rack
– Power supply: 12 V (DC), a suitable power supply is included
nTransmitter: Battery powered bodypack transmitter
Depending on the environmental conditions, it is possible to operate six, at 823 MHz four par‐
allel systems and to mount them in one rack.
Features
UHF wireless system
12
The system operates with pre-programmed frequency groups. The following table shows the
number of available pre-programmed groups and the number of pre-programmed frequen‐
cies in each group.
Type Pre-programmed fre‐
quency groups
Available channels per
group
the t.bone free solo PT 600 MHz (item no. 296201) 14 15
the t.bone free solo PT 823 MHz (item no. 296204) 8 8
the t.bone free solo PT 863 MHz (item no. 296206) 1 16
the t.bone free solo PT 660 MHz (item no. 380970) 14 16
Features
free solo PT
13
4 Installation and starting up
4.1 General Information
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the product against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
Create all connections while the device is Use the shortest possible high-quality cables foro.
all connections. Take care when running the cables to prevent tripping hazards.
Installation and starting up
UHF wireless system
14
nThis device utilizes frequencies that are not harmonized within the European Union (EU)
and therefore may only be used in certain EU member states. In all European countries, the
frequencies used for the transmission of audio signals are strictly regulated. Before you
start, make sure the frequencies are allowed in the respective country and check whether
the operation must be reported to the appropriate authority.
For more information, please visit: .http://www.thomann.de
nMake sure that transmitter and receiver are both tuned to the same channel.
nNever set multiple transmitters to the same channel.
nMake sure that there are no metal objects between the transmitter and receiver.
nAvoid interference from other radio or in-ear systems.
4.2 Receiver
The unit has been designed for rack mounting in a standard 19" rack; it occupies one rack unit.
The material required for assembly is included.xing
Notes on wireless transmission
Rack mounting
Installation and starting up
free solo PT
15
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the
external power supply, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual cur‐
rent circuit breaker. Failure to do so could result in damage to the device and pos‐
sibly the user.
Unplug the external power supply before electrical storms occur and when the
device is unused for long periods of time to reduce the risk of electric shock or
re.
First, connect the power adapter to the receiver and then plug the power adapter into the
power outlet.
Connecting the power supply
Installation and starting up
UHF wireless system
16
Attach the included antennas to the rear panel of the transmitter. To improve the transmission
quality and to adapt to the spatial conditions they are rotatable and swivelling.
In case the space provided on the device for direct assembly of the antennas is not sucient,
for example because the space on the rack is narrow, you can use the optionally available
coaxial cable to assemble the antennas separately from the device. For larger combinations
with up to four receivers, an antenna distributor is optionally available.
Connect one of the audio outputs of the receiver to your mixer or your Ensure thatamplier.
only one of the two outputs is ever used at a time, because faults might occur otherwise.
4.3 Transmitter
Open the lid of the battery compartment by sliding it in the direction of the arrow, and insert
the batteries. Pay attention to the correct location of the poles. Close the battery compartment
and switch the transmitter on. The "LOW BATT" LED lights up.briey
Attaching the antennas
Connecting audio and starting
up
Inserting batteries into the
transmitter
Installation and starting up
free solo PT
17
nEnsure that the transmitter is switched o.
nConnect the microphone or instrument cable to the input on the transmitter (mini-XLR
panel connector).
nTurn on the transmitter and check the transmission by using the microphone or instru‐
ment. If necessary, adjust the of the transmitter and the levels on youramplication
mixing console or your amplier.
Connecting the microphone or
instrument to the transmitter
Installation and starting up
UHF wireless system
18
5 Connections and operating elements
5.1 Receiver
POWER
TRUE DIVERSITY RECEIVER
free solo
SET
AUTOADL
+3 40
0
- 5
- 10
- 15
- 20
- 25
- 30
AF
35
30
25
20
15
10
RF SQ
AUTOIR
A B
GP
FREQUENCY MHz
CH
18.18
888 888
.
DATA SYNC
#
ö$ ) (%
. - & '
iR
Front panel
Connections and operating elements
free solo PT
19
1[POWER]
Press the switch for several seconds to switch the device on or o.
All previous settings are retained even when you switch the device and disconnect it from the mains.o
2 Infrared receiver
3[ADL]
Starts the synchronization of the settings with the transmitter.
4 Display
5[SET]
Opens the menu.
6
Increases the displayed value by one.
7
Decreases the displayed value by one.
Connections and operating elements
UHF wireless system
20
8[AUTO]
Starts an automatic search to a free channel.nd
12, 13 Suitable UHF antennas
The receiver evaluates the radio signal coming from both antennas and selects the signal with the higher quality for
further processing.
Connections and operating elements
free solo PT
21
BALANCED
OUTPUT
UNBALANCED
OUTPUT ANTENNA-B ANTENNA-A
D.C 12-18V
500mA
* + , - .
FREQ.
863~865MHz
/
Rear panel
Connections and operating elements
UHF wireless system
22
9[DC 12-18V]
Socket for connecting the supplied AC power supply. If you are using a power supply, observe the correctdierent
voltage, the polarity of the plug and the power consumption.
10 [BALANCED OUTPUT]
XLR panel plug as balanced audio signal output for direct connection to a mixer, a power amp or recording device.
11 [UNBALANCED OUTPUT]
1/4" phone socket as unbalanced audio signal output for direct connection to a mixer, a power amp or recording
device.
12, 13 , [ANTENNA-B] [ANTENNA-A]
Suitable UHF antennas
The receiver evaluates the radio signal coming from both antennas and selects the signal with the higher quality for
further processing.
14 Indicating the frequency range in which the device operates. The indication here must match the information on the
transmitter.
Connections and operating elements
free solo PT
23
+3 40
0
- 5
- 10
- 15
- 20
- 25
- 30
AF
35
30
25
20
15
10
RF SQ
AUTOIR
A B
GP
FREQUENCY MHz
CH
18.18
888 888
.
9:; 8 7 6 5
0 1 2 3 4
Display
Connections and operating elements
UHF wireless system
24
15 [GP]
Indicates the selected frequency group.
16 [CH]
Indicates the selected channel.
17
Indicates that the unit is locked to prevent unintentional operation.
18
Indicates that the receiver does not receive a signal, e.g. because the transmitter is disabled, the connection is inter‐
rupted or the channel is just changing.
19 [A/B]
Shows which of the two antennas is currently being used for signal transmission.
20 [SQ]
Shows the set squelch level for the radio signal. Setting the squelch too high will lower the dynamics of the system.
21 [RF]
Shows the level of the radio signal received.
Connections and operating elements
free solo PT
25
22 Shows the battery status of the transmitter from which the device just received a signal.
23 [AUTO]
Shows that an automatic search is running to a free channel.nd
24 [IR]
Indicates that an infrared signal is being received.
25 [FREQUENCY]
Indicates the frequency that is assigned to the set combination of frequency group and channel.
26 [AF]
Level display for the audio signal
Connections and operating elements
UHF wireless system
26
5.2 Transmitter
IR SET
BAT T
LOW
ON MUT E
GP CH
GAIN
0
dB
FREQ UEN CY MH z
838 000
.
B
D
H
C
J
B
AI
E
F
G
B
K
L
Connections and operating elements
free solo PT
27
31 Display
32 Antenna
33 [MUTE]
Shows that the device has been muted.
34 / [BATT LOW] [ON]
Blinks when the battery is too low.
35 [SET]
Opens the menu.
36 , keys
Increases or decreases the currently displayed value.
37 Battery holder for two round cell batteries (AA, LR06), 1.5 V or comparable rechargeable batteries.
38 [IR]
Infrared sensor
Connections and operating elements
UHF wireless system
28
39 INPUT
Mini-XLR chassis plug for connecting a microphone or instrument.
40 Main switch
Press the switch for several seconds to switch the device on or Press the switch once to mute the input.o. briey
When the transmitter is muted, the symbol does not appear on the receiver display.
41 Indicating the frequency range in which the device operates. The here must match the specication specication
printed on the back of the receiver.
42 Retaining clamp
Connections and operating elements
free solo PT
29
51 / / [FREQUENCY] [GP] [CH]
Depending on selected menu item:
nIndicates the frequency that is assigned to the set combination of frequency
group and channel.
nDisplays the set frequency group and the set channel.
52
Indicates that the unit is locked to prevent unintentional operation.
53 [GAIN]
Shows the level of the radio signal sent.
54 Battery level indicator. Replace the batteries when only one blinking bar remains
displayed. Reduces the voltage of the batteries even further if the transmitter is
automatically switched The battery status is also shown on the receiver.o.
GP CH
GAIN
0
dB
FREQUENCY MHz
838 000
.
Connections and operating elements
UHF wireless system
30
55
Shows that the transmitter has been muted. This is the case if the transmitter and
receiver are working on frequencies, if the receiver is not getting a usabledierent
signal or if you have muted the transmitter by pressing the main switch.briey
56 Shows the output power.
Connections and operating elements
free solo PT
31
6 Operating
6.1 Receiver
1. Press .[SET]
ðThe display blinks.[GP]
2. Use the arrow keys to select the frequency group.
Press to the selection.[SET] conrm
ðThe display blinks.[CH]
3. Use the arrow keys to select a channel within the set frequency group.
If you have selected frequency group , you can use the arrow keys to set the fre‐‘U’
quency directly in 25-kHz increments. First set the value before the decimal point, and
press . Then set the value after the decimal point.[SET]
Press to the selection.[SET] conrm
Selecting frequency
Operating
UHF wireless system
32
ðThe display shows that the receiver is being adjusted to the new frequency. After a
few seconds, the display shows the normal sate again.
1. Open the transmitter to expose the infra red sensor.
2. Press . The display blinks.[ADL] [IR]
3. Hold the infrared sensor of the transmitter near the infrared interface of the receiver
within ten seconds.
4. When synchronization has been successfully completed, the display stops blinking.[IR]
ðAfter three seconds, the display shows the default state again.
Synchronizing transmitter and
receiver
Operating
free solo PT
33
In case of model versions for the 1.8 GHz range, you can set the output level directly with the
arrow buttons.
In case of other model versions, proceed as follows:
1. Hold down until the area blinks on the display.[SET] [AF]
2. Use the arrow buttons to set the desired value. The current value is shown on the left
side of the display.
3. Press to the selection.[SET] conrm
ðAfter three seconds, the display shows the default state again.
1. Hold down until the area blinks on the display.[SET] [SQ]
2. Use the arrow buttons to set the desired value. The current value is shown on the right
side of the display.
3. Press to the selection.[SET] conrm
ðAfter three seconds, the display shows the default state again.
Setting the output level
Setting squelch
Operating
UHF wireless system
34
1. Press .[AUTO]
ðThe display blinks; the display shows the number of free channels available.[AUTO]
2. Use the arrow keys to select one of the free channels.
Press to the selection.[SET] conrm
ðAfter three seconds, the display shows the default state again.
3. If the system does not a free channel within seconds, it automatically returns tond ve
the default state.
Automatic search for a free
channel
Operating
free solo PT
35
1. Hold down until the symbol appears.[SET]
ðAll keys except for the main switch are locked.
2. To unlock the keypad, press , until the symbol is no longer visible.[SET]
ðThe keys have their original function again.
6.2 Transmitter
The keys for operating the device are located under the on the front side.ap
Locking or unlocking the
keypad
Operating
UHF wireless system
36
If you don't wish to synchronize the transmitter with the receiver using the infra red interface,
you can set the transmitting frequency manually in the frequency group (usercongurable
bank).
1. Keep pressing until the value in the blinks on the display.[SET] [GP] eld
2. Use the arrow keys to select the frequency group.
Press to the selection.[SET] conrm
ðThe number in the blinks.[CH] eld
3. Use the arrow keys to select a channel within the set frequency group.
If you have selected frequency group "U", you can use the arrow keys to set the fre‐
quency directly. First set the value before the decimal point, and press . Then set the[SET]
value after the decimal point.
Press to the selection.[SET] conrm
ðAfter a few seconds, the display shows the default state again.
Select frequency
Operating
free solo PT
37
1. Keep pressing until the number in the blinks on the display.[SET] [GAIN] eld
2. Use the arrow keys to change the transmitter gain in increments of 3 dB (-6 dB, -3 dB,
0 dB).
Press to the selection. Press the main switch to close the menu without[SET] conrm
making any changes.
1. Keep pressing until the symbol blinks on the display.[SET]
2. Use the arrow keys to change the transmitter power (5 mW, 10 mW, 20 mW).
Press to the selection. Press the main switch to close the menu without[SET] conrm
making any changes.
Setting gain
Setting transmitter power
Operating
UHF wireless system
38
1. Press .
ðThe display shows the frequency group and channel being used.
2. Press or wait seconds to return to normal state.[SET] ve
Hold down until the symbol appears.
ðAll keys except for the main switch are locked.
To unlock the keypad, press , until the symbol is no longer displayed.
ðThe keys have their original function again.
Displaying frequency group and
channel
Locking the keypad
Unlocking the keypad
Operating
free solo PT
39
7 Technical specications
7.1 Transmitter
Carrier frequency UHF band (600 MHz…1.8 GHz)
Frequency band the t.bone free solo PT 600 MHz (item no. 296201): 596 MHz…620 MHz
the t.bone free solo PT 823 MHz (item no. 296204): 823 MHz…832 MHz
the t.bone free solo PT 863 MHz (item no. 296206): 863 MHz…865 MHz
the t.bone free solo PT 660 MHz (item no. 380970): 675 MHz…679 MHz
Bandwidth the t.bone free solo PT 600 MHz (item no. 296201): 24 MHz
the t.bone free solo PT 823 MHz (item no. 296204): 9 MHz
the t.bone free solo PT 863 MHz (item no. 296206): 2 MHz
the t.bone free solo PT 660 MHz (item no. 380970): 24 MHz
Switching band width 25 kHz
Technical specications
UHF wireless system
40
Modulation type Frequency modulation (FM)
Maximum transmission power the t.bone free solo PT 600 MHz (item no. 296201): 20 mW
the t.bone free solo PT 823 MHz (item no. 296204): 20 mW
the t.bone free solo PT 863 MHz (item no. 296206): 10 mW
the t.bone free solo PT 660 MHz (item no. 380970): 20 mW
Spurious response rejection ratio > 55 dBc
Peak deviation ± 55 kHz
NF frequency response 60 Hz 18 kHz…
Total harmonic distortion (THD) < 0.5 %
Signal-to-noise ratio > 102 dB (A)
Power supply 2 AA cells (LR6, 1.5 V) or corresponding rechargeable batteries
Range of the infrared connection for the syn‐
chronization between transmitter and receiver
80 mm
Operating time > 8 h (with alkaline cells)
Technical specications
free solo PT
41
Dimensions (W × D × H, without antenna) 64 mm × 23 mm × 98 mm
Weight 90 g
Ambient conditions Temperature range 0 °C…40 °C
Relative humidity 20 %…80 % (non-condensing)
Technical specications
UHF wireless system
42
7.2 Receiver
Input connections Power supply Input socket for external power adapter
Output connections Audio signal XLR chassis plug, balanced
1/4" phone socket (unbalanced)
Sensitivity –102 dBm
NF frequency response 50 Hz 15 kHz ( 3 dB)… ±
Total harmonic distortion (THD) < 0.8 %
Signal-to-noise ratio > 105 dB (A)
Power supply External power adapter, 100 - 240 V 50/60 Hz
Operating voltage 12 V / 1000 mA, centre positive
Dimensions (W × H × D, without antennas) 212 mm × 44 mm × 160 mm
Weight 900 g
Technical specications
free solo PT
43
Ambient conditions Temperature range 0 °C…40 °C
Relative humidity 20 %…80 % (non-condensing)
Carrier frequency, frequency band, number of channels, bandwidth, switching bandwidth and
modulation type correspond to those of the transmitter.
Technical specications
UHF wireless system
44
Guitar channels 1
Transmission technology Analog
Transmitter type Bodypack transmitter
Receiver type Stationary
Detachable antenna BNC
Charging system No
Built-in battery No
Suitable antennas converter Optionally available (item no. 177448)
Accessories Guitar cable, rack mount and plastic case included
Further information
Technical specications
free solo PT
45
8 Plug and connection assignment
This chapter will help you select the right cables and plugs to connect your valuable equip‐
ment in such a way that a perfect sound experience is ensured.
Please note these advices, because especially in ‘Sound & Light’ caution is indicated: Even if a
plug into the socket, an incorrect connection may result in a destroyed power amp, a shortts
circuit or ‘just’ in poor transmission quality!
Unbalanced transmission is mainly used in semi-professional environment and in use.hi
Instrument cables with two conductors (one core plus shielding) are typical representatives of
the unbalanced transmission. One conductor is ground and shielding while the signal is trans‐
mitted through the core.
Unbalanced transmission is susceptible to electromagnetic interference, especially at low
levels, such as microphone signals and when using long cables.
In a professional environment, therefore, the balanced transmission is preferred, because this
enables an undisturbed transmission of signals over long distances. In addition to the conduc‐
tors ‘Ground’ and ‘Signal’, in a balanced transmission a second core is added. This also transfers
the signal, but phase-shifted by 180°.
Introduction
Balanced and unbalanced trans‐
mission
Plug and connection assignment
UHF wireless system
46
Since the interference both cores equally, by subtracting the phase-shifted signals, theaects
interfering signal is completely neutralized. The result is a pure signal without any noise inter‐
ference.
1 Signal
2 Ground, shielding
1 Signal (in phase, +)
2 Signal (out of phase, –)
3 Ground
1/4" TS phone plug (mono,
unbalanced)
1/4" TRS phone plug (mono, bal‐
anced)
Plug and connection assignment
free solo PT
47
1 Ground, shielding
2 Signal (in phase, +)
3 Signal (out of phase, –)
4 Shielding on plug housing (option)
A mini-XLR panel connector serves as a signal input on the transmitter. The and thegure
table show the mini-XLR pin assignment.
1 Ground
2 Positive signal (+)
3 Negative signal (–)
XLR plug (balanced)
Mini-XLR connections for signal
input on the transmitter
Plug and connection assignment
UHF wireless system
48
9 Troubleshooting
In the following we list a few common problems that may occur during operation. We give you
some suggestions for easy troubleshooting:
Troubleshooting
free solo PT
49
Symptom Remedy
No sound 1. Check the power supply of transmitter and receiver.
2. Make sure that transmitter and receiver are operating in the same frequency
range. The frequency range can be found on the devices.
3. Are transmitter and receiver set to the same channel?
4. Test the connection between the receiver and the connected audio device
(amplier, mixer). Is the connected audio device turned on and does the signal
level at the output of the receiver match the input requirements of the audio
device?
5. See if the audio transmission works when you move the transmitter closer to
the receiver.
6. Make sure that no metal objects near the transmitter or receiver obstruct the
transmission.
Transmission is interrupted. 1. Modify the orientation of the antennas.
Troubleshooting
UHF wireless system
50
Symptom Remedy
2. If you use more than one wireless system at the same time, check the used
frequencies and channels.
3. Interference can also be caused by other radio or in-ear systems.
If the procedures recommended above do not succeed, please contact our Service Center. You
can the contact information at .nd www.thomann.de
Troubleshooting
free solo PT
51
10 Protecting the environment
For the transport and protective packaging, environmentally friendly materials have been
chosen that can be supplied to normal recycling.
Ensure that plastic bags, packaging, etc. are properly disposed of.
Do not just dispose these materials with your normal household waste, but make sure that
they are fed to a recovery. Please follow the notes and markings on the packaging.
Batteries must not be disposed of as domestic waste or thrown into Dispose of the bat‐re.
teries according to national or local regulations regarding hazardous waste. To protect the
environment, dispose of empty batteries at your retail store or at appropriate collection sites.
Disposal of the packaging mate‐
rial
Disposal of batteries
Protecting the environment
UHF wireless system
52
This product is subject to the European Waste Electrical and Electronic Equipment Directive
(WEEE) in its currently valid version. Do not dispose with your normal household waste.
Dispose this device through an approved waste disposal or through your local wasterm
facility. When discarding the device, comply with the rules and regulations that apply in your
country. If in doubt, consult your local waste disposal facility.
Disposal of your old device
Protecting the environment
free solo PT
53

Especificaciones del producto

Marca: The T.bone
Categoría: micrófono
Modelo: free solo PT

¿Necesitas ayuda?

Si necesitas ayuda con The T.bone free solo PT haz una pregunta a continuación y otros usuarios te responderán


micrófono The T.bone Manuales

The T.bone

The T.bone DC-4000 Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone freeU HT 600 Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone freeU HT 863 Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone MB-55 Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone freeU HT 823 Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone TWS One Vocal Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone RB100 Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone SC450 USB Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone Speech 100 C Manual de Usario

5 Septiembre 2024
The T.bone

The T.bone TWS One Guitar Manual de Usario

5 Septiembre 2024

micrófono Manuales

Últimos micrófono Manuales

Shure

Shure SBC210LM Manual de Usario

25 Octubre 2024
Akg

Akg GN50 M Manual de Usario

25 Octubre 2024
Countryman

Countryman B6 Manual de Usario

19 Octubre 2024
Pyle

Pyle PMKSHUSB04 Manual de Usario

19 Octubre 2024
Trust

Trust 21670 Manual de Usario

18 Octubre 2024
Neumann

Neumann U 87 Ai Manual de Usario

18 Octubre 2024
BOYA

BOYA BY-PM700 Manual de Usario

18 Octubre 2024
Audio-Technica

Audio-Technica BP892xCW Manual de Usario

17 Octubre 2024
Audio-Technica

Audio-Technica BP4073 Manual de Usario

15 Octubre 2024
Power Dynamics

Power Dynamics PD524 Manual de Usario

15 Octubre 2024