Ultimaker S5 Air Manager Manual de Usario

Ultimaker Impresora S5 Air Manager

Lee a continuación 📖 el manual en español para Ultimaker S5 Air Manager (21 páginas) en la categoría Impresora. Esta guía fue útil para 11 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/21

Ultimaker S5 Air Manager

Installation and user manual

EN 03/2020 v2.2

Ultimaker S5 Air Manager user manual 1

Table of contents

1. Safety and compliance

1.1 Safety messages 4

1.2 General safety information 4

1.3 Hazards 4

1.4 Health and safety 5

2. Introduction

2.1 Main components 7

2.2 Specications 7

3. Unboxing

3.1 Unboxing 9

3.2 What’s in the box 9

3.3 Hardware installation 10

3.4 Firmware installation 10

4. Operation

4.1 Operation recommendations 12

4.2 Printing with the Air Manager 12

4.3 Uninstalling the Air Manager 13

5. Maintenance

5.1 Clean the Air Manager 15

5.2 Replace the lter 15

6. Troubleshooting

6.1 Error codes 17

6.2 Air Manager not recognized 17

7. Warranty

7.1 General 19

7.2 Conditions 19

7.3 Notication 20

7.4 Exclusions 20

7.5 Applicable law and competent court 20

Ultimaker S5 Air Manager user manual 2

Disclaimer

Please read and understand the contents of this installation and user manual carefully. Failure to read the manual

may lead to personal injury, inferior results or damage to the Air Manager, the Ultimaker S5 or its peripherals.

Always make sure that anyone who uses this 3D printer knows and understands the contents of the manual to

make the most out of the Ultimaker S5 Air Manager.

The Ultimaker S5 Air Manager, together with the Ultimaker S5 Material Station and the Ultimaker S5 form the

Ultimaker S5 Pro Bundle. This user manual specically describes the intended workow and operation for the

Ultimaker S5 Air Manager. First time Ultimaker S5 users are advised to consult the Ultimaker S5 Pro Bundle manual.

The conditions or methods used for assembling, handling, storage, use or disposal of the device are beyond our

control and may be beyond our knowledge. For this and other reasons, we do not assume responsibility and

expressly disclaim liability for loss, injuries, damage, or expense arising out of or in any way connected with the

assembly, handling, storage, use or disposal of the product.

The information in this document was obtained from sources which we believe are reliable. However, the

information is provided without any warranty, express or implied, regarding its correctness.

Intended use

The Ultimaker S5 Air Manager is designed and built for use in combination with the Ultimaker S5. The Ultimaker

S5 Air Manager fully encloses the build chamber of the Ultimaker S5 and creates an inside-out airow through the

lter that removes up to 95% of all ultrane particles (UFPs). This results in a safer work environment when printing

with an extended range of materials - both Ultimaker and third-party materials. The exact number of ultrane

particles ltered can vary per material. The user remains responsible for taking (additional) safety measures if

necessary based on the information provided by the lament supplier.

Especificaciones del producto

Marca:	Ultimaker
Categoría:	Impresora
Modelo:	S5 Air Manager
Peso.:	2500 g
Ancho:	305 mm
Profundidad:	244 mm
Altura:	108 mm
Bluetooth:	Ja
Estándares wifi:	Wi-Fi 6 (802.11ax)
Versión Bluetooth:	5.1
red LAN:	Ja
Número de puertos Ethernet LAN (RJ-45):	1
Número de puertos USB 3.2 Gen 1 (3.1 Gen 1) Tipo A:	4
Zócalo del procesador:	Socket AM4
Fabricante del procesador:	AMD
Memoria interna máxima:	128 GB
Canales de salida de audio:	7.1 kanalen
placa base con chipset:	AMD X570
Número de puertos USB 3.2 Gen 2 (3.1 Gen 2) Tipo A:	8
Tipo de ranura de memoria:	DIMM
Salida S/PDIF:	Ja
Interfaces de unidad de almacenamiento compatibles:	M.2, PCI Express 3.0
Componente para:	PC
Número de conectores SATA III:	8
Procesadores compatibles:	AMD Ryzen 3, AMD Ryzen 5
Tipos de memoria soportados:	DDR4-SDRAM
Wifi.:	Ja
Código del Sistema Armonizado (SA):	84733020
Familia de chipsets de placa base:	AMD
Factor de forma de la placa base:	ATX
Número de ranuras de memoria:	4
Velocidades de reloj de memoria admitidas:	4000,4133,4266,4400,4600,4666,4800,4866 MHz
tipo de BIOS:	UEFI AMI
Tamaño de la memoria del BIOS:	256 Mbit
Soporte para procesamiento paralelo:	2-Way CrossFireX, 2-Way SLI, 3-Way CrossFireX
Conexión para refrigerador de CPU:	Ja
Conexiones USB 2.0:	6
Conexiones USB 3.2 Gen 1 (3.1 Gen 1):	1
Conector TPM:	Ja
Borrar perilla CMOS:	Ja
Conexiones para fuentes de alimentación EATX:	1
Conectores USB 3.2 (3.1 Gen 2):	1