V7 UPS1TW1500-1N Manual de Usario

V7 Unión Postal Universal UPS1TW1500-1N

Lee a continuación 📖 el manual en español para V7 UPS1TW1500-1N (2 páginas) en la categoría Unión Postal Universal. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
UPS 1500VA TOWER US
Installation & Operation
UPS
Product Overview
Fault Code Table
1. Inspection
The following items are inside the box: UPS Unit, User Manual
Remove the UPS from its package and inspect it for damage that may have occurred during
shipping. If any damage is discovered, re-pack the unit and return it to the place of purchase.
2. Connect to Utility Power
Connect AC power cord to utility power. Then, the UPS will start to charge inside battery. For best
result, charge the battery for 6 hours prior to initial use.
3. Plug in Equipment
Battery back-up Outlets (5)
Connect computer and monitor to the “Battery Backup” outlets. These outlets provide battery
backup, EMI ltering, line conditioning, and surge protection. Battery power is automatically
provided in case of power failure.
Surge-Protected Outlets (5)
Connect a printer, fax machine, or scanner to the “Surge-protected” outlets. These outlets do not
provide power during power failure.
CAUTION: NEVER connect a laser printer or scanner to the battery backup sockets of UPS. The
equipment may draw signicantly power to overload the UPS
4. Turn On/Othe UPS
To turn on the UPS unit, hold the power button until you hear a beep. To turn o the UPS unit,
hold the power button until it beeps. Then, display will shut o.
1. LCD display or LED indicators
(Please check LCD section for
the details)
2. Power Switch
3. Mute Button
4. Up/down button
5. AC Input
6. Circuit Breaker
7. Surge-protected outlets
8. Battery Backup Outlets
9. USB port (option)
10. Modem/phone/network surge
protection (option)
11. Coax surge protection (option)
Fault Condition SolutionsLCD
Output short circuited Disconnect short-circuited loads and
restart the UPS again
Inverter/Output failure Call for service immediately
Overcharge
1. Turn o the unit and wait for cooling.
2. Or remove excessive loads and wait
for cooling.
Note: If fault alarm occurs, please call for service immediately.
LED DISPLAY UPS1DT550-1N only
Operation Display
UPS Mode DescriptionLCD
UPS Power ON When UPS is powered on, all icons will
light up 1 second
Standby Mode
Site wiring fault in
standby mode Low Battery
AC Mode
When AVR is functioning,
icon will ash
every second.
Press button to switch displayed
information.
1. Output voltage
2. Output frequency
3. Input voltage
4. Input frequency
5. Output power in kW
6. Output power in kVA
7. Estimated backup time
Overload in AC mode
icon will ash
When overload occurs, alarm will beep
every 0.5 second.
Site wiring fault in AC
mode
Battery Mode
In battery mode, press
button to mute
alarm and icon will
be on.
Alarm will beep every 10 seconds and
LCD information will be displayed in the
following order when pressing
button.
1. Estimated backup time
2. Output voltage
3. Output frequency
4. Input voltage
5. Input frequency
6. Output power in kW
7. Output power in kVA
When battery level is low,
icon will ash
Alarm will beep every second. This alarm
can not be mute.
Overload in battery mode
icon will ash
When overload occurs, alarm will beep
every 0.5 second.
NOTE: The backlight will be always on when any fault or warning occurs.
5. Install software (Optional for advanced users)
For optimal computer system protection, install UPS monitoring software to fully congure the UPS
system. Please follow steps below to download and install monitoring software.
1. Go to the website http://www.V7-world.com/downloads
2. Select ViewPower software for your operating system to download the software.
3. Follow the on-screen instructions to install the software.
1
2
3
4
10
5 6
7 8
11
9
Safety Information
TroubleshootingSpecications
Problem Possible Cause Solutions
Nothing is displayed on
the panel
The UPS is not on Press the power switch again to turn on
the UPS
Battery voltage is too low Charge the battery at least 6 hours
Battery fault Replace the battery
The UPS always on
battery mode Power cord is loose Re-plug the power cord
The UPS continuously
beeps or displays battery
“REPLACE” icon
Battery is disconnected
Open the front battery cover by pushing
in then pulling down. Check to make
sure the battery is properly connected
Battery needs to be
replaced Replace the battery
Fault Code Check the fault code table for details
Backup time too short
Battery voltage is too low Charge the battery at least 6 hours
Overload
Remove unnecessary load. Before
reconnecting equipment, pleasee verify
that the load matches the UPS capability
in the specication
Battery defect Replace the battery
* If any abnormal situations occur that are not listed above, please call for service immediately
V1-20170328
Caution -risk of electric shock. The battery circuit is not isolated from the input voltage. Hazardous
voltages may occur between the battery terminals and the ground. Before touching, please verify that
no voltage is present!.
Remove the connection from ground if any part of the battery is determined to be grounded.
When changing batteries, install the same number and same type of batteries..
Do not attempt to dispose of batteries by burning them. This could cause battery explosion.
Do not open or destroy batteries. Escaping electrolyte can cause injury to the skin and eyes. It may be
toxic.
Please replace the fuse or circuit breaker only with the same type and amperage in order to avoid re
hazards.
Do not dismantle the UPS system,except the specialized technical personnel.
This unit intended for installation in a controlled environment (temperature controlled, indoor area free
of conductive contaminants). Avoid installing the UPS in locations where there is standing or running
water, or excessive humidity.
Do not plug the UPS input into its own output.
Do not attach a power strip or surge suppressor to the UPS.
Do not attach non-computer-related items, such as medical equipment, life-support equipment, micro-
wave ovens, or vacuum cleaners to UPS.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit dierent from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING: Changes or modications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Do not dispose of batteries in a re as they may explode.
Batteries may cause electric shock and have a high short-circuit current. Please take the precautionary
measures specied below and any other measures necessary when working with batteries:
1. Remove wristwatches, rings and other metal objects
2. Use only tools with insulated grips and handles.
3. Wear rubber gloves and boots.
4. Do not lay tools or metal parts on top of batteries.
5. Disconnect charging source and load prior to installing or maintaining the battery.
Internal battery voltage is 12VDC.Sealed, lead-acid, 6-cell battery.
Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and
the required precautions. Keep unauthorized personnel away from batteries.
Do not open or mutilate the battery or batteries. Release electrolyte is harmful to the skin and eyes. It
may be toxic.
Attention, hazardous through electric shock. Also with dis- connection of this unit from the mains,
hazardous voltage still may be accessible through supply from battery. The battery supply should be
therefore disconnected in the plus and minus pole at the connectors of the battery when mainte-
nance or service work inside the UPS is necessary.
To reduce the risk of overheating the UPS, do not cover the UPS’ cooling vents and avoid exposing
the unit to direct sunlight or installing the unit near heat emitting appliances such as space heater or
furnaces.
Unplug the UPS prior to cleaning and do not use liquid or spray detergent.
Model 1500
CAPACITY 1.5KVA/900W
Input Voltage 120 VAC
Input Voltage Range 90-140 VAC
Output Voltage Regulation ± 5 % (Bat. mode)
Transfer Time Typical 6 ms, max. 10 ms
Waveform Simulated Sine Wave
Battery Type & No 12V/9Ah x 2
Charging Time 6-8 hours recover to 90% capacity
Dimension (DxWxH) 16” x 4” x 11”
Net Weight (lbs) 26lbs (11.79 kg)
Humidity 0-90% RH @ 0-40°C non-condensing)
Noise Level Less than 45dB @ 1 meter (3 ft.)

Especificaciones del producto

Marca: V7
Categoría: Unión Postal Universal
Modelo: UPS1TW1500-1N

¿Necesitas ayuda?

Si necesitas ayuda con V7 UPS1TW1500-1N haz una pregunta a continuación y otros usuarios te responderán




Unión Postal Universal V7 Manuales

Unión Postal Universal Manuales

Últimos Unión Postal Universal Manuales