Valcom Page Zone Extender VIP-801 Manual de Usario

Valcom No categorizado Page Zone Extender VIP-801

Lee a continuación 📖 el manual en español para Valcom Page Zone Extender VIP-801 (3 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/3

1 947995

ISSUE 6

VIP-801

ENHANCED NETWORK AUDIO PORT

INTRODUCTION

The VIP-801 Enhanced Network Audio Port

enables voice access to a single zone of one-way

paging over an IP network, allowing page zones

to be extended anywhere network connectivity is

available. The VIP-801 can be programmed as a

SIP (Session Initiation Protocol) device for

connectivity to virtually any Voice over IP (VoIP)

telephone system.

SPECIFICATIONS

Features

 1 Audio Output or Input

 2 Form C Relays

 1 Contact Closure Input

 1 SIP identity for registering to a VoIP telephone

system

 RJ-45 jack for network connection

 Front panel activity LED

 Provides audio for up to 40 Valcom one-way

amplified speaker assemblies

 AUX audio input via RCA jack

 Contact closure or VOX operation of audio input

 Removable screw terminal connectors provided

for audio and relay interface

 AUX input music mutes during page

 Output control contact closure provided during

paging output

 Compatible with 25 or 70 Volt amplifiers

 2.5mm jack for optional DC power

 Power over Ethernet (PoE) 802.3af compatible

Dimensions/Weight

 1.38 H x 6.13" W x 5.25" D

(3.50cm H x 15.6cm W x 13.33cm D)

 Weight: 1.25 lbs. (0.57 kg)

Nominal Specifications

Input Impedance: 600 Ohms

Input Level: -10dBm nominal

Voice Switch Sensitivity: -21dBm

AUX Input Impedance: 8 to 600 Ohms

AUX Input Level: -10dBm nominal

Output Impedance: 50 Ohms

Output Level: - 10dBm nominal

Relay Current: 1 Amp @ 24VDC

Nominal Power Requirements

Via rear panel barrel connector:

Voltage: 24VDC

Current: 325mA

Via 802.3af PoE Ethernet Switch:

802.3af: Class 3

Environment

Temperature: 0 to +40° C

Humidity: 0 to 85% non-precipitating

Packing List

Qty Item

1 VIP-801

1 VSP Document

2 Mounting Brackets W/ Hardware

4 Rubber Pads

2 947995

CAUTION: To reduce the risk of electric shock,

Do not remove cover.

No user serviceable parts inside.

Refer servicing to qualified service pe rsonnel.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

This symbol indicates that dangerous

voltage constituting a risk of electric

shock is present with in this unit.

This symbol indicates that there are

important operating and maintenance

instructions in the literature accompanying

this unit.

INSTALLATION

FCC Information

This equipment has been tested and found to

comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable

protection against harmful interference when

the equipment is operated in a commercial

environment. This equipment generates, uses

and can radiate radio frequency energy and if

not installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a residential area

may cause harmful interference in which case

the user will be required to correct the

interference at his own expense.

Precautionary Designations

Mounting

The VIP-801 is designed for wall or table mounting.

Table: Provided with the VIP-801 are four rubber

pads. Peel the pads from their carrier backing

and place at the four corners of the bottom of the

unit.

Wall: Using the brackets and screws provided,

secure the VIP-801 to the wall.

Power Connections

The preferred method of powering a VIP-801 is via

a power over Ethernet switch meeting the 802.3af

specification.

If the rear panel barrel connector is used for power,

the preferred power supply is a Valcom VIP-324D.

Make all required signal connections before

applying power to the unit. If powering via 802.3af,

make sure all signal connections via the back panel

are made then connect the VIP-801 to the Ethernet

switch.

If power is supplied via the barrel connector, make

sure all signal connections are secure. Attach the

unit to the network via the front panel RJ-45

Ethernet connector. Apply power by plugging the

power supply into the VIP-801 via the barrel

connector on the rear of the VIP-801.

Network Connection

The VIP-801 has one RJ-45 network connector on

the front panel. Use a standard Ethernet patch

cable to connect the VIP-801 to an Ethernet switch.

Signal Connections

The VIP-801 has 4 signal connectors on the rear

panel:

 RCA jack for AUX audio input

 2 Pin screw terminal for audio output

 6 Pin screw terminal for relay connections

 4 Pin screw terminal for audio input and contact

closure input

AUX Input: Local audio may be input via the

rear panel RCA jack. Nominal input impedance

is 600 Ohms. Connect any compatible audio

source using an RCA patch cable. Audio

supplied through the rear panel RCA jack is

transformer coupled to Audio Out when Audio Out

is idle. This is typically used for background music.

Audio Out: Typically connects to Self Amplified

Speakers or into an amplifier. AUX Input audio

mutes when Audio Out is receiving page audio.

Audio Input/Contact Closure: The audio input

and contact closure share a four pin terminal

connection. Neither input is polarity sensitive.

The contact closure is on the right two terminals

labeled "CC". The audio input is on the left two

terminals labeled "AUDIO".

3 947995

K1 K2 INPUTSAUDIOAUX

OUTIN AUDIO CC

+24V DC

N.C.

N.O.

N.C.

N.O.

COM

STATUS

LINK

ACT

Relay Channels: Access to the two form C relays

is provided via a six pin screw terminal block. The

relays are labeled K1 and K2. Each relay is

brought out on three terminals. The common

contact is the middle terminal with the normally

closed contact on the right and the normally open

contact on the left. Relay contacts are rated for 1A

@ 24VDC.

Rear View

Status Indicator Lights

The VIP-801 has 3 status indication lights on the

front panel:

STATUS: Flashes during normal operation and

solid during system startup.

LINK: Indicates a 100 Mbit Ethernet connection

when illuminated. A non-illuminated LINK LED

indicates a 10 Mbit connection or no network

connection.

ACT: Indicator flashes to indicate network activity.

Front View

Setup

Information specific to your application will need

to be programmed into the VIP-801 using a

computer. The PC used for programming should

be connected to the same subnet as the VIP-801.

Setup will be done using the IP Solutions Setup

Tool. Download the latest version of the free IP

Solutions Setup Tool from the Valcom web site at

www.valcom.com/vipsetuptool.

TECHNICAL ASSISTANCE

When trouble is reported, verify power is being

supplied to the unit and there are no broken

connections. If a spare unit is available, substitute

a spare unit for the suspected defective unit.

Assistance in troubleshooting is available from the

factory. Call (540) 563-2000 and press 1 for

Technical Support or via email at

support@valcom.com.

When requesting assistance, you should include all

available information. General information and

troubleshooting procedures are available on the

Valcom website at www.valcom.com.

Valcom equipment is not field repairable. Valcom,

Inc. maintains service facilities in Roanoke, VA.

Should repairs be necessary, attach a tag to the

unit clearly stating your company name, address,

phone number, contact person and the nature of

the problem. Send the unit to:

Valcom, Inc.

Repair & Return Dept.

5614 Hollins Road

Roanoke, Va. 24019-5056

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products only to the original purchaser, for its own use, to be free from defects in materials and workmanship under conditions of

normal use and service for a period of one year from the date of shipment. This Limited Warranty obligation shall be limited to the replacement, repair or refund

of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim;

2. the defect is not the result of damage, misuse or negligence after the original shipment;

3. the product has not been altered in any way or repaired by others and that factory sealed units are unopened (a service charge plus parts

and labor will be applied to units defaced or physically damaged);

4. freight charges for the return of products to Valcom are prepaid;

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs (major repairs will be subject to

additional charges for parts and labor).

This Limited Warranty is in lieu of and excludes all other warranties, expressed or implied and in no event shall Valcom, Inc. be liable for any

anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the purchase, operation,

maintenance, installation, removal or use of the product. The maximum liability of Valcom under this warranty is limited to the purchase price of the

specific Product covered by the warranty.

Disclaimer. Except for the Limited Warranty provided herein, the product is provided “as-is” without any warranty of any kind whatsoever including, without

limitation, any WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT.

This warranty specifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier should be notified

immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

5614 Hollins Road Roanoke, VA 24019-5056

Phone: (540) 563-2000 FAX: (540) 362-9800