Vantec UGT-CR961 Manual de Usario

Lee a continuación 📖 el manual en español para Vantec UGT-CR961 (4 páginas) en la categoría Lector de tarjetas de memoria. Esta guía fue útil para 8 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/4
Prepare your computer case for installation.
2. Locate an available 3.5” or 5.25” drive bay where you would like
to install the device.
3.
5.25” Drive Bay
3.5” Drive Bay
*Using Optional 3.5” to 5.25” Front Bay Converter Kit (HDA-525P) to install into a 5.25” Front Bay
Slide the front panel device into your case until the front panel
is flush with the front of your case.
1b. Secure the 5.25” front panel device to your computer case with
the provided screws.
2b. Proceed to connect the front panel device to your system’s
motherboard or expansion card.
3b.
Connect to
System 20 pin
USB 3.0 Header
Connect to
System Audio
port Header
Connect to
System SATA
port Header
Proceed to connect the front panel device to your system’s
motherboard or expansion card.
3a.
Secure the 3.5” front panel device to your computer case with
the provided screws.
2a.
Slide the front panel device into your case until the front panel
is flush with the front of your case.
1a.
3.5” Front Panel Installation
Connect to
System 20 pin
USB 3.0 Header
Connect to
System Audio
port Header
Connect to
System SATA
port Header
Installation Guide Guía de instalación Guide d'installation Installationsanleitung
Guida all’installazione 付け 安裝指南 安装指南
Verify the package contents.
1.
3.5” Front Panel Device Installation Guide
Installation Screws
Secure with the screws provided by the 3.5” to 5.25” front panel
converter bracket.
3.
Slide in the 3.5” front panel device into the front bay converter kit
until the front panel is flush.
2.
Prepare the 3.5” to 5.25” front panel converter kit.
If you would like to mount your 3.5” device into your 5.25” drive bay, you may do so by using Vantec’s HDA-525P 3.5“ to 5.25” bay converters. Follow the steps below to convert your device form factor to 5.25”.
1.
Converting Your 3.5” Front Panel Device to 5.25” Form Factor
Make sure all connection are connected well and place the cover
back on to your case.
5. Drivers will be automatically detected and installed. Your device
will be ready for use.
6.
Copyright © 2012 Vantec Thermal Technologies. All Right Reserved. | All Registered Trademarks Belong To Their Respective Companies.
v1.01
Information in this document is subject to change without notice.
Reproduction of these materials in any manner whatsoever without written permission is strictly forbidden.
Printed in China
Printed on Recycled Paper.
Diagram shown is the USB 3.0 20-Pin found on supported motherboards or expansion cards. Please refer to your motherboard
manufacturer’s documentation for the location of these ports.
*
Connecting Your Front Panel Device
4.
SATA
SATA header on system
Note: Missing pin
and notch on the
connector matches
notch on the head
USB 3.0(20-pin*) header on system
Audio header
on system
Note: Missing pin
Connect to
System 20 pin
USB 3.0 Header
Connect to
System Audio
port Header
Connect to
System SATA
port Header
Supports all standard memory cards.

Especificaciones del producto

Marca: Vantec
Categoría: Lector de tarjetas de memoria
Modelo: UGT-CR961

¿Necesitas ayuda?

Si necesitas ayuda con Vantec UGT-CR961 haz una pregunta a continuación y otros usuarios te responderán




Lector de tarjetas de memoria Vantec Manuales

Lector de tarjetas de memoria Manuales

Últimos Lector de tarjetas de memoria Manuales