Ventev TW-COLOMOUNT-2 Manual de Usario

Ventev No categorizado TW-COLOMOUNT-2

Lee a continuación 📖 el manual en español para Ventev TW-COLOMOUNT-2 (2 páginas) en la categoría No categorizado. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/2
Mounting Instructions
Note: The Co-Locating Mount can be mounted on any at surface including, but not limited to, walls, ceilings, and I-beams. Mounting hardware
is not included with this product. User should identify the mounting surface and then purchase the appropriate mounting hardware.
Caution: Ensure the mounting surface will support the fully assembled units weight including the mount itself, the access point, and the antenna.
Figure 2
2. Detach the circular Surface Mounting Plate from the Access Point Mounting Plate by
unscrewing the Chase Nipple nut. Set aside the Chase Nipple nut for later use. Retain the
Chase Nipple within the Surface Mounting Plate.
Figure 3
3. Set aside the combined Access Point Mounting Plate/Antenna Mounting Tray for later use.
Figure 4
4. Place the Surface Mounting Plate over the desired mounting location, with the four Surface
Mounting Stand-Os touching the mounting surface.
5. Pull the RJ-45 cable through the Chase Nipple and allow it to hang loose.
6. Insert four screws or bolts into the four Surface Mounting Holes. Tighten the screws/bolts
until the Surface Mounting Plate is secure against the mounting surface.
Figure 2
Figure 4
Figure 3
Surface
Mounting
Stand-os
Dry Wall Mounting:
- 4x Wall Anchors
- 4x Dry Wall Screws that t the holes shown in Figure 2.
Wood Wall Mounting:
- 4x Wood Screws that t the holes shown in Figure 2.
- 4x Locking Washers
Metal Surface Mounting
- 4x Metal Screws that t the holes shown in Figure 2.
- 4x Flat Washers
- 4x Locking Washers
Recommended Hardware:
Locking Screws
Antenna
Mounting
Tray
Cable
Management Clips
Swing Arm
Locking Tab
Thumb
Screws
TToward Antenna
Coverage Area
TToward Mounting
Surface
Access Point
Mounting Plate
Surface Mounting
Plate
4x Surface
Mounting Holes
Chase Nipple
Chase
Nipple Nut
Chase
Nipple
Threads
Surface
Mounting
Plate
Figure 1
1. Major parts of the Dual Axis Co-Locating Mount. Refer to it as required for the remaining steps.
Figure 5
7. Position the combined Access Point Mounting Plate/Antenna Mounting Tray so that
the threaded Chase Nipple inserts into the Access Point Mounting Plates hole. Thread
the Chase Nipple nut onto the Chase Nipple and nger tighten. The mated assembly
should look like Figure 5.
Figure 6
8. Locate the four Access Point Mounting Slots (circled) in the Access Point Mounting Plate.
9. Insert the access point’s rubber mounting feet into the Access Point Mounting Slots.
Slide the mounting feet inside the Mounting Slots until the access point locks into place
with an audible snap.
10. Recommended step for securing the access point: Secure the access point to the Access
Point Mounting Plate through the locking tab. The most common method is to thread a
zip-tie through the Mounting Plates locking tab and the access points adjacent locking
tab and tighten the zip-tie.
11. Insert the RJ-45 cable into Access Point’s RJ-45 port.
Figure 7
12. Remove the nuts and washers from Antenna mounting bolts located at rear of the antenna.
Push the antennas mounting bolts through the holes in the Antenna Mounting Tray.
13. Re-attach antenna washers and nuts and tighten them to hold antenna securely against
Mounting Tray.
14. Run antenna cables through cable management clips and attach cable connectors to the
Access Point.
15. Optional steps for positioning antenna:
a. The Chase Nipple nut is still only nger tight. Rotate the combined Access Point
Mounting Plate/Antenna Mounting Tray until it is in the desired position. Tighten the
Chase Nipple Nut so further rotation is impossible.
b. Loosen the Antenna Mounting Trays thumb screws and locking screws. Rotate
the Antenna Mounting Tray to achieve the desired antenna position. Tighten all screws.
Chase
Nipple Nut
Chase Nipple
Threads
Figure 5
Figure 6
Figure 7

Especificaciones del producto

Marca: Ventev
Categoría: No categorizado
Modelo: TW-COLOMOUNT-2

¿Necesitas ayuda?

Si necesitas ayuda con Ventev TW-COLOMOUNT-2 haz una pregunta a continuación y otros usuarios te responderán




No categorizado Ventev Manuales

No categorizado Manuales

Últimos No categorizado Manuales