Vimar 01488 Manual de Usario

Vimar Monitor 01488

Lee a continuación 📖 el manual en español para Vimar 01488 (2 páginas) en la categoría Monitor. Esta guía fue útil para 3 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Descargar PDF

Página 1/2

Viale Vicenza 14

36063 Marostica VI - Italy

www.vimar.com

01488 01 1906

01488

Home automation control device with four push buttons and 240 V~ 50/60Hz

phase-cut dimmer, for incandescent lamps 40-200 W, electronic transformers

40-300 VA 240 V~, 20-150 VA 120 V~, CFL lamps 10-200 W 240 V~, 5-100 W 120

V~, LED lamps 3-200 W 240 V~, 3-100 W 120 V~, visible in darkness with RGB

LEDs with intensity adjustment, to be completed with interchangeable half-but-

ton caps comprising 1 or 2 modules (Eikon) or 2 modules (Arkè or Plana).

The device controls the load directly. It should be used as a double or single push button

depending on the chosen button; the push buttons can also be configured independently

from the dimmer actuation part and can be pressed either at the top or bottom. For the

Eikon and Arkè series, all the button covers, whether from the catalogue or customised,

have symbols which can be backlit with customisable RGB colours.

IMPORTANT: Lamps controllable from a single output must all be the same. All con-

trollable loads must be declared DIMMABLE by the manufacturer. Check the type of

compatible dimming on the lamp packaging: LE (Leading Edge) or TE (Trailing Edge).

Where not specified, the lamp works in both modes, at the discretion of the installer;

choose the type of dimming that ensures the best lamp operation.

FEATURES.

• TP BUS Rated supply voltage: 29 V

• Mains rated supply voltage: 240 V~, 50 Hz/60 Hz

• Absorption from TP bus: 15 mA

• Combinable buttons: double or 1 single

• Terminals: L, dimmer output, TP bus

• Output protected against overload or overcurrent

• Max device-load distance 100 m

• Operating temperature -5 °C +45 °C (indoor)

• IP20 protection degree

• Device 01488 should be configured with the Automation Gateway 01410-01411 and

App VIEW Pro.

• Not compatible with By-me control panels 21509 and EasyTool Professional.

CONTROLLABLE LOADS.

• Controllable loads with load adaptor 01873 connected in parallel:

• Controllable RGB loads with load adaptor 01873 connected in parallel:

Plug&Play.

CAUTION: The plug&play mode requires the system to include only plug&play devic-

es and not devices configured in the By-me Plus system.

For operation in Plug&Play mode, only install the 1-module fixed half-button caps on

the device.

In the absence of a configuration, the device is pre-configured as follows:

- briefly press to B turn on the load;

- press for a prolonged time to make the (increase);B upwards adjustment

- briefly press to C turn off the load;

- press for a prolonged time to make the (decrease);C downwards adjustment

- press to send a “ ” scenario over the bus;F Lights OFF

- press to send a “E Lights OFF and roller shutters DOWN” scenario over the bus.

When push buttons are pressed, the LEDs are on for 3 s.

Important: in plug&play mode the output does not manage the RGB load

SETTING THE COLOUR OF THE LEDS.

PLUG&PLAY mode.

• Procedure activation: simultaneously press push buttons E and F for a prolonged time;

the LEDs will all illuminate in the colour currently set.

• E F Colour selection: briefly press push button or to view the next colour.

• Saving the colour and exiting the procedure: press push button or for a prolonged F E

time.

• Exiting the procedure without saving the colour: automatic after a timeout of 5 s.

B y-me Plus SYSTEM.

• The colour is set from the App using the respective menus.

L ED indications

• The flashing of any of the LEDs of push buttons B and C is an indication of an alarm.

• If both the B and C LEDs are flashing, the electrical power supply output is absent.

• Flashing LED C indicates the device’s thermal protection has been triggered.

Check the connections of the corresponding load; also make sure it is not excessive

or unsuitable.

• To silence the alarm, briefly press push button B or C (ON/OFF of the corresponding

dimmer).

If the flashing continues, wait for the protection to cool down and then repeat the

command.

OPERATION.

Home automation device acting as a dimmer actuator.

• Possible functions of the buttons:

- ON/OFF switch

- roller shutter control

- dimmer control

- scenario activation

• Possible functions of the dimmer:

- lights on, lights off and light control

- “flash start” mode for CFL lamps

- “ramp” operation

- off delay and “warning” function

- phase control: LE/TE

• Possible functions of the dimmer with dedicated RGB loads:

- lights on, lights off and light control

- absolute colour change

- fading show operation

CONFIGURATION.

For the configuration operations, see the By-me Plus system manual.

We recommend you configure the device with the load turned off.

Configuration must be done with the device without the button to be able to press the

configuration push button A.

• Functional units: 7 (4 push buttons, 2 rocker buttons and 1 dimmer actuator)

• Functional unit selection during configuration:

- press push button and wait 3 s to select the dimmer functional unit;A

- press push button again followed by the desired button ( ) to select the A B C E F, , ,

related push button or rocker button functional unit.

Configuration begins with the turning on of the red LED and ends with it being turned off.D

INSTALLATION RULES.

• Installation must be carried out by qualified persons in compliance with the current

regulations regarding the installation of electrical equipment in the country where the

products are installed.

• The lamps connected to it must all be the same. White LEDs and RGB LEDs cannot be

controlled simultaneously using the same device.

• Not suitable for controlling motors (e.g. fans, ventilators).

• Never exceed the rated power.

• If installing 2 dimmers in a single box, the controllable loads by each dimmer must be

reduced so that their total does not exceed the maximum power that can be controlled

by a single device.

• Overloads, electric arcs and short-circuits cause irreparable damage to the dimmer.

Before installation check the circuit carefully and eliminate any of the above causes.

• The dimmer does not have a mechanical 1-way switch in the main circuit and so is not

galvanically separated. The circuit load should be considered always powered.

REGULATORY COMPLIANCE.

LV Directive. EMC directive.

Standards EN 60669-2-5, EN 50491.

REACH (EU) Regulation no. 1907/2006 – Art.33. The product may contain traces of lead.

Dimming with leading edge LE

phase control

Dimming with trailing edge TE

phase control

Controllable loads LE TE

40 - 200 W 40 - 200 W

10 - 100 W 10 - 200 W (max 5 lamps) (max 10 lamps)

5 - 100 W 10 - 200 W (max 5 lamps) (max 10 lamps)

40 - 200 VA

(max 3

type transformers)

40 - 200 VA

(max 5

type transformers)

Controllable loads LE TE

Power supply units

01874-01875

max 10 power supply units Not applicable

Lamps 02662

max 10 lamps Not applicable

RGB lamps 02663

max 10 lamps

Viale Vicenza 14

36063 Marostica VI - Italy

www.vimar.com

01488 01 1906

FRONT AND REAR VIEW

Key:

A: Configuration button

B. Push button 1

C. Push button 2

D. LED

E: Push button 3

F: Push button 4

DTP bus

CONNECTIONS

Connection with 01873

Connection with 01873 and lamp 02663

-Bus

BUS

–+

6 mm

-Bus

BUS

–+

6 mm

Connection with load

L, dimmer output

BUS

–+

6 mm

-Bus

BUS

–+

6 mm

WEEE - User information

The crossed bin symbol on the appliance or on its packaging indicates that the product at the end of its life must be collected separately from other waste. The user must therefore hand the equipment at the end of its

life cycle over to the appropriate municipal centres for the differentiated collection of electrical and electronic waste. As an alternative to independent management, you can deliver the equipment you want to dispose of

free of charge to the distributor when purchasing a new appliance of an equivalent type. You can also deliver electronic products to be disposed of that are smaller than 25 cm for free, with no obligation to purchase, to

electronics distributors with a sales area of at least 400 m2. Proper sorted waste collection for subsequent recycling, processing and environmentally conscious disposal of the old equipment helps to prevent any possible

negative impact on the environment and human health while promoting the practice of reusing and/or recycling materials used in manufacture.

Especificaciones del producto

Marca:	Vimar
Categoría:	Monitor
Modelo:	01488
Color del producto:	Black, Blue
Pantalla incorporada:	Ja
Peso.:	621.4 g
Ancho:	120.14 mm
Profundidad:	120.14 mm
Altura:	146.04 mm
Bluetooth:	Ja
Incluye adaptador de CA:	Ja
Función de repetición:	Ja
Altavoces incorporados:	Ja
Energía promedio:	- W
tipo de sintonizador:	Digitaal
Voltaje de entrada:	100-240 V
Función de reloj:	Ja
Bandas de frecuencia soportadas:	FM
Número de canales preestablecidos:	6
Radio:	Klok
Compatibilidad con acoplamiento de Apple:	Niet ondersteund