Vitek VTC-C594DN Manual de Usario

Vitek No categorizado VTC-C594DN

Lee a continuación 📖 el manual en español para Vitek VTC-C594DN (8 páginas) en la categoría No categorizado. Esta guía fue útil para 6 personas y fue valorada con 4.5 estrellas en promedio por 2 usuarios

Página 1/8
VTC-C594DN
1/3" Hi-Res Day/Night Color CCD Camera
INSTRUCTION MANUAL
1. General
This color video camera employs a 1/3” SONY solid-state, charge coupled
imaging device, and is equipped with a newly developed DSP (Digital Signal
Processor) for video signal processing to provide high color fidelity and a
sharp, stable picture.
2. Features
1. Accepts IR illumination for surveillance in total darkness. Delivers color
images in daylight and automatically switches to black-white images at
night.
2. 420 lines of horizontal resolution and high quality video utilizing digital
processing
3. 0.015lux
(@ F0.75)
Minimum illumination and signal - -to noise ratio of 48 dB
is achieved by employing a highly sensitive image sensor with micro lenses
and low noise circuit design.
4. High quality picture –A digital signal processor performs digital horizontal
and vertical aperture enhancement to produce a high quality picture.
5. A newly developed intelligent wide range Auto Tracing White Balance (ATW)
that automatically adjusts the tone according to the color temperature of the
light source.
6. Smart digital control
Auto BLC, the combination of Histogram
equalizer and
Central windows weighting BLC functions ensure for use against any
unusual lighting conditions.
7. Advanced Auto Exposure System for both fixed iris and auto iris lenses
controls the amount of light to ensure optimum video signal.
8. Internal or Line-lock external sync.
Warning:
To prevent fire or electric shock hazard, do not expose
the appliance to rain or moisture
To prevent electric shock, do not remove screws or covers.
There are no user serviceable parts inside.
Contact a qualified service person if necessary.
M
N
B
C
E
A
D
H
F
G
I
L
VTC-C594DN
J
K
3. Name of Parts and Functions
A.
C (CS) mount ada pter
B.
Flange focal distance adjustment -If back focus adjustment is necessary, unscrew
the flange back lock screw; optimize the focus by turning this ring.
C. Mounting screw hole
Standard photographic pan-head screw size (1/4” – 20)
D. Flange focal lock screw
E.
Auto iris lens connector (MINI JACK)
See 3.1 (Auto-iris connector)
F.
Video/DC Auto-Iris Lens Selector.
VIDEO---For VIDEO Drive Lens
DC------- For DC or D/D Direct Drive Lens
G. DC lever Adjuster (VR)
For DC D/D auto iris lens drive level adjustment for obtaining correct exposure to
light.
H. Video output terminal (BNC)
This connector is used to connect to the VIDEO IN connector of a monitor or
processor.
I.
Auto Exposure Mode SW
AES Low Mode SW
Auto Backlight
ON/OFF SW
Auto Iris Mode SW
Auto iris +Shutter Mode SW
AE Convergence (Av. / Pk )
AGC Max / Super SW
GAMMA (.45 / 1) SW
FL=FLICKERLESS, CCD- -I=CCD IRIS, AI SHUT = AUTO IRIS + SHUTTER
SPEED, Av =
AVERAGE,
Pk = PEAK, AGC=30dB, SUPER=36dB.
DC VIDEO
Manual Exposure SW
Manual Shutter speed select SW
Manual Gain SW for ME Mode
AE
FLOFF
BLC
CCD-I
NORM
Av
NAGC
?
=.45
ME
FL
BLCOFF
AUTO IRIS
AI SHUT
Pk
SUPERAGC
? = 1
0 1
J.
SW2
White Balance mode SW
Add. detail see AWB section
VBS in 75OHM ON/OFF SW
(For Gen-lock model)
K. MWB adjust button
Line-lock Phase
Adjustment
L.
AWB push to lock button
Detail pls. See
AWB
section
M. Power pilot LED
N. AC24V / DC12V Block Terminal
1.1 Auto Iris Lens Connector
Use the accompanying auto iris lens control connector plug.
For auto iris lens with built-in EE amp. (VIDEO Type)
Set the lens selector switch to ”Video” position.
Connector cable leads
1.Red---- power
2.NC
3.White-- video
4.Black--
shielded
For auto iris lens without EE amp. (DC Type)
This is the external view of camera
Set the lens selector switch to “DC” position.
Connector cable leads
1.
Damping coil ( -)
2. Damping coil (+)
3. Driving coil (+)
4.
Driving coil ( -)
Connect the leads as shown above; refer to the instructions of the lens.
1.2
Power Terminal
1.2.1
AC24V/DC12V model
This terminal accepts both AC 24V and DC 12V
non-polarity
1.2.2
Line-Lock Phase Adjustment
The vertical phase of the camera video signal can be matched to the phase of the
AC power line.
Using a dual-trace oscilloscope to observe the video output signal
(V- -rate) of the camera and adjust the Line lock Phase control buttons
to line up the phase of both signals
Caution:
The adjustment must be
made by qualified servicing
person or system installer.
PHASE
Phase adjusting Buttons for Line-lock
model.
1
2
3
4
DC12V
G
NC
~DC2
PTL
WB1
WB2
WB3
NC

Especificaciones del producto

Marca: Vitek
Categoría: No categorizado
Modelo: VTC-C594DN

¿Necesitas ayuda?

Si necesitas ayuda con Vitek VTC-C594DN haz una pregunta a continuación y otros usuarios te responderán




No categorizado Vitek Manuales

No categorizado Manuales

Últimos No categorizado Manuales